• 한국정밀공학회지
• /
• 제23권7호
• /
• pp.101-107
• /
• 2006

Cold gas dynamic spray or cold spray is a novel manufacturing method for coatings. Cold spray is a high rate and direct material deposition process that utilizes the kinetic energy of particles sprayed at high velocity (300-1,200m/s). In this research, a technique to repair the damaged mold by cold spray deposition and mechanical machining was proposed. An aluminum 6061 mold with three-dimensional surface was fabricated, intentionally damaged and material-added by cold spray, and its original geometry was re-obtained successfully by Computer Numerical Control (CNC) machining. To investigate deformation of material caused by cold spray, deposition was conducted on thin aluminum plates ($100mm{\times}100mm{\times}3mm$). The average deformation of the plates was $205{\sim}290{\mu}m$ by Coordinate Measurement Machine (CMM). In addition, the cross section of deposited layer was analyzed by scanning electron microscopy (SEM). To compare variation of hardness, Vickers hardness was measured by micro-hardness tester.

• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.30-37
• /
• 2012

Pneumatic Active Engine Mount(PAEM) with open-loop control system has been developed to reduce the transmission of the idle-shake vibration induced by engine effectively and economically. A solenoid valve installed between PAEM and vacuum tank is on-off switched by the Pulse Width Modulate(PWM) control signal to decrease the dynamic stiffness of the engine mount. This paper presents the methodology to identify the optimal values of control parameters of a PAEM, i.e, turn-on timing and duty ratio of PWM signal for 6 different idle driving conditions. A scanning algorithm was first applied to the vehicle test to obtain the approximate optimal control parameters minimizing the vibration at front seat rail and at steering wheel. Then the PAEM system identification was fulfilled to find accurate optimal control parameters by using multi-layer neural networks of Levenberg-Marquardt algorithm with vehicle test data.

• 센서학회지
• /
• 제18권6호
• /
• pp.461-466
• /
• 2009

This paper represents a piezoelectric ultrasonic linear actuator with flexural vibration mode. The actuator is composed of two piezo ceramics, the elastic body, and the connecting tip. It is driven by the frictional force between the connecting tip and the linear motion guide. Unimorph actuators have flexural vibration. Its middle point is fixed so that suitable to the flexural vibration of $3/2\lambda$. These vibrations contribute to elliptical motion by mixed mode between longitudinal and transverse mode. It was generated when the ultrasonic electrical signals with 90 degree phase difference are applied to two ceramics. A linear movement can be easily obtained using the elliptical motion. The ATILA, FEM simulator has been used to design actuator and verify the kinetic and dynamic analysis. We used the ceramics of $20\times10\times1$ mm size and confirmed the flexural vibration of the $3/2\lambda$ at the 79 kHz through the scanning of 3D-vibrometer. The maximum velocity of actuator was 221 mm/sec and the thrust force of actuator was 2.7 N in 200Vp-p of additional voltage.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제8권11호
• /
• pp.3810-3836
• /
• 2014

Geo-location white space spectrum databases (GL-WSDBs) are currently the preferred technique for enabling spectrum sharing between primary users and secondary users or white space devices (WSDs) in the very-high frequency (VHF) and ultra-high frequency (UHF) bands. This is true because technologies for making low-cost WSDs capable of autonomous sensing and detection of available white space (WS) spectrum are not yet feasible. This paper reviews the necessary enabling technical conditions to allow coexistence of primary and secondary systems in the VHF and UHF spectrum through a GL-WSDB approach. The practical implementation of South Africa's first GL-WSDB was performed. Results of WS channels available from five cities in South Africa calculated from the implemented GL-WSDB was compared with a commercially available GL-WSDB and was found to be 68% similar. Additionally, results from the implemented GL-WSDB were compared with measurements obtained from field spectrum scanning campaigns at two different locations in Cape Town, South Africa, and was found to be 64% similar.

• International Journal of Advanced Culture Technology
• /
• 제3권1호
• /
• pp.13-20
• /
• 2015

The self-cleaning properties of nano-zinc oxide on cotton fabrics have been investigated. The cotton fabric has been prepared by pad-dry method. The nano-zinc oxide was encapsulated in the polystyrene particle by mini-emulsion process prior used. The loading amount of zinc oxide particles into the mini-emulsion were various from 1% wt to 40%wt. The particles sizes of ZnO-encapsulated polystyrene mini-emulsion were determined using dynamic light scattering. It was showed that the particle size of the mini-emulsion was in the range of 124-205 nm. The topography and morphology of ZnO-encapsulated polystyrene which coated on cotton fabrics was observed using scanning electron microscopy. The crystal structure of ZnO-coated on cotton fabrics was explored by X-ray diffraction spectroscopy. The photocatalytic activities of zinc oxide were present through the self-cleaning properties. The presents of the zinc oxide on cotton fabrics significantly showed the improving of the self-cleaning properties under UV radiation.

• Animal cells and systems
• /
• 제12권2호
• /
• pp.101-108
• /
• 2008

Recently, Platypus koryoensis has been reported as a major pest of oak trees in Korea which can introduce the pathogenic fungus(Raffaelea sp.) by making galleries into the heartwood of the tree. As the beetle has developed its effective drilling mouthpart enough to make tunnels, we have analyzed the fine structural aspects of the mouthpart using the field emission scanning electron microscopy(FESEM) to reveal its mechano-dynamic characteristics. The mouthparts of this ambrosia beetle which consist of a labrum, a pair of mandibles, a pair of maxillae and the labium exhibit typical morphology of mycophagous coleopteran beetles and have those characteristics of chewing mouthparts that can excavate galleries in the hardwood. Both of maxillary and labial palpi have the functions of direct the food to the mouth and hold it while the mandibles chew the food. The distal ends of these palpi are flattened and have shovel-like setae. Females have larger maxillary palpi and a larger gular region than males in general.

• Macromolecular Research
• /
• 제15권7호
• /
• pp.623-632
• /
• 2007

Thermosensitive nanoparticles were prepared via the self-assembly of two different $poly({\varepsilon}-caprolactone)$-based block copolymers of poly(N-isopropylacrylamide)-b-$poly({\varepsilon}-caprolactone)$ (PNPCL) and poly(ethylene glycol)-b-$poly({\varepsilon}-caprolactone)$ (PEGCL). The self-aggregation and thermosensitive behaviors of the mixed nanoparticles were investigated using $^1H-NMR$, turbidimetry, differential scanning microcalorimetry (micro-DSC), dynamic light scattering (DLS), and fluorescence spectroscopy. The copolymer mixtures (mixed nanoparticles, M1-M5, with different PNPCL content) formed nano-sized self-aggregates in an aqueous environment via the intra- and/or intermolecular association of hydrophobic PCL chains. The microscopic investigation of the mixed nanoparticles showed that the critical aggregation concentration (cac), the partition equilibrium constants $(K_v)$ of pyrene, and the aggregation number of PCL chains per one hydrophobic microdomain varied in accordance with the compositions of the mixed nanoparticles. Furthermore, the PNPCL harboring mixed nanoparticles evidenced phase transition behavior, originated by coil to the globule transition of PNiPAAm block upon heating, thereby resulting in the turbidity change, endothermic heat exchange, and particle size reduction upon heating. The drug release tests showed that the formation of the thermosensitive hydrogel layer enhanced the sustained drug release patterns by functioning as an additional diffusion barrier.

• Corrosion Science and Technology
• /
• 제7권5호
• /
• pp.243-251
• /
• 2008

Magnesium alloys become popular research topic in last decade due to its light weight and relatively high strength-to-weight ratio in the energy aspiration age. Almost all structure materials are supposed to suspend stress. Magnesium is quite sensitive to corrosive environment, and also sensitive to environmental assisted cracking. However, so far we have the limited knowledge about the environmental sensitive cracking of magnesium alloys. The corrosion fatigue (CF) test was conducted. Many factors' effects, like grain size, texture, heat treatment, loading frequency, stress ratio, strain rate, chemical composition of environment, pH value, relative humidity were investigated. The results showed that all these factors had obvious influence on the crack initiation and propagation. Especially the dependence of CF life on pH value and frequency is quite different to the other traditional structural metallic materials. In order to interpret the results, the electrochemistry tests by polarization dynamic curve and electrochemical impedance spectroscopy were conducted with and without stress. The corrosion of magnesium alloys was also studied by in-situ observation in environmental scanning electron microscopy (ESEM). The corrosion rate changed with the wetting time during the initial corrosion process. The pre-charging of hydrogen caused crack initiated at $\beta$ phase, and with the increase of wetting time the crack propagated, implying that hydrogen produced by corrosion reaction participated in the process.

• 한국재료학회지
• /
• 제16권7호
• /
• pp.422-429
• /
• 2006

Studies were performed on preparation of organic-inorganic hybrid silica dye in a dispersing ink system. The silica was subjected to surface modification using 3-aminopropyltrimethoxysilane (APTMS) in order to promote the chemical reactivity of the raw silica. On the surfaces of the aminosilane-functionalised silica, red vinylsulfone-containing azo dye was adsorbed. The dye was found to have chemically reacted with the aminosilane-grafted silica surface, which was proven by FT-IR spectra. Studies on morphology and microstructure were performed employing scanning electron microscopy. The SEM micrographs and particle size distributions showed that a homogeneous pigment can be obtained employing silica as a core. Particle size distribution was also examined using the technique of dynamic light scattering. The ensuing pigment was subjected to various physicochemical evaluation such as inkjet property, storage stability, color change as inkjet ink using printer, spectrophotometric, microscopic techniques. Studies on hybrid dyes from the silica surface demonstrated that, in general, stable pigments for inkjet dispersion ink were obtained.

• Macromolecular Research
• /
• 제12권5호
• /
• pp.478-483
• /
• 2004

Two different diene monomers [dicyclopentadiene (DCPD) and 5-ethylidene-2-norbornene (ENB)] as self-healing agents for polymeric composites were microencapsuled by in situ polymerization of urea and formaldehyde. We obtained plots of the storage modulus (G') and tan $\delta$ as a function of cure time by using dynamic mechanical analysis to investigate the cure behavior of the unreacted self-healing agent mixture in the presence of a catalyst. Glass transition temperatures (T$\_$g/) and exothermic reactions of samples cured for 5 and 120 min in the presence of different amounts of the catalyst were analyzed by differential scanning calorimetry. Of the two dienes, ENB may have advantages as a self-healing agent because, when cured under same conditions as DCPD, it reacts much faster in the presence of a much lower amount of catalyst, has no melting point, and produces a resin that has a higher value of T$\_$g/. Microcapsules containing the healing agent were successfully formed from both of the diene monomers and were characterized by thermogravimetric analysis. Optical microscopy and a particle size analyzer were employed to observe the morphology and size distribution, respectively, of the microcapsules. The microcapsules exhibited similar thermal properties as well as particle shapes and sizes.