• Journal of Korea Water Resources Association
• /
• v.48 no.5
• /
• pp.321-330
• /
• 2015

In recent, the impacts of urbanization on hydrology and water quality can be minimized with the use of Low Impact Development (LID) practices in urban areas. But, there are no ways to verify or to show the quantitative effectiveness with LID practices. This study designed and developed to perform experiments in natural or artificial representation of hydrological cycle, which is called rainfall-runoff simulator to be able to quantify factors in hydrological system. This simulator was applied to a pervious pavement block. The study conducted analysis of effectiveness for a pervious pavement block by comparing the results with a general pavement block. The result from the pervious pavement block showed remarkably reduction effect on surface runoff with increase of rainfall intensity and more duration time. Also, the simulator was possible to control no surface runoff by a rainfall intensity at 50 mm/hr for an hour. The research indicated possibility and effectiveness for LID practices. This might be widely available to apply to LID practices verification. Therefore, the study is possible to make use of practical standards on fundamental studies.

• Sleep Medicine and Psychophysiology
• /
• v.4 no.2
• /
• pp.164-171
• /
• 1997

Introduction : Periodic limb movement disorder (PLMD) is shown to common in patients with OSA and may become evident or worsened when treated with nasal continuous positive airway pressure (CPAP). Whether this is due to im proved sleep continuity. adverse nocturnal body positioning, uncovered by CPAP, or due to the CPAP stimulus is still debat-ed. We hypothesized that the increase in PLM activity following CPAP is associated with more supine-sleeping tendencies when being treated with CPAP. In the present work, we compared differences in the PLMD index (PLMI) and sleeping position of patients with sleep disordered breathing before and after CPAP treatment. Method : We studied 16 patients (mean age 46 yr, 9M, 7F) with OSA (11 patients) or UARS (5 patients) who either had PLMD on initial polysomnogram (baseline PSG) or on nasal CPAP trial (CPAP PSG). All periodic leg movements were scored on anterior tibialis EMG during sleep according to standard criteria (net duration; 0.5-5.0 seconds, intervals; 4-90 seconds. 4 consecutive movements). Paired t-tests compared PLMD index (PLMI), PLMD-related arousal index (PLMD-ArI), respiratory disturbance index (RDI), and supine sleeping position spent with baseline PSG and CPAP PSG. Results : Ten patients (63%) on baseline PSG and fifteen patients (94%) on CPAP PSG had documented PLMD ($PLMI{\ge}5$) respectively with significant increase on CPAP PSG(p<0.05). Ten patients showed the emergence (6/10 patients) or substantial worsening (4/10 patients) of PLMD during CPAP trial. Mean CPAP pressure was $7.6{\pm}1.8\;cmH_2O$. PLMI tended to increase from baseline PSG to CPAP PSG, and significantly increase when excluding 2 outlier (baseline PSG, $19.0{\pm}25.8/hr$ vs CPAP PSG, $29.9{\pm}12.5/hr$, p<0.1). PLMD-ArI showed no significant change, but a significant decrease was detected when excluding 2 outlier (p<0.1). There was no significant sleeping positional difference (supine vs non-supine) on baseline PSG, but significantly more supine position (supine vs non-supine, p<0.05) on CPAP PSG. There was no significant difference in PLMI during supine-sleeping and nonsupine-sleeping position on both of baseline PSG and CPAP PSG. There was also no significant difference in PLMI during supine-sleeping position between baseline PSG and CPAP PSG. With nasal CPAP, there was a highly significant reduction in the RDI (baseline PSG, $14.1{\pm}21.3/hr$ vs CPAP PSG, $2.7{\pm}3.9/hr$, p<0.05). Conclusion : This preliminary data confirms previous findings that CPAP is a very effective treatment for OSA, and that PLMD is developed or worsened with treatment by CPAP. This data also indicates that supine-sleeping position is more common when being treated with CPAP. However, there was no clear evidence that supine position is the causal factor of increased PLMD with CPAP. It is, however, suggested that the relative movement limitation induced by CPAP treatment could be a contributory factor of PLMD.

• Journal of IKEEE
• /
• v.19 no.2
• /
• pp.186-192
• /
• 2015

This paper proposes an automatic generation technology of test case based on API in source code for software's quality improvement. The proposed technology is comprised of four processes which are analyzing source code by using the Doxygen open source tool, defining API specification by using analyzed results, creating test design, generating a test case by adapting Pairwise test technology. Analyzing source code by using the Doxygen open source tool is the phase in which API information in source code such as the API name, input parameter and return parameter are extracted. Defined API specification by using analyzed results is the phase where API informations, which is needed to generate test case, are defined as a form of database by SQLite database on the basis of extracted API information. Creating test design is the phase in which the scenario is designed in order to be composed as database by defining threshold of input and return parameters and setting limitations based on the defined API. Generating a test case by adapting Pairwise test technique is the phase where real test cases are created and changed into database by adapting Pairwise technique on the base of test design information. To evaluate the efficiency of proposed technology, the research was conducted by begin compared to specification based test case creation. The result shows wider test coverage which means the more cases were created in the similar duration of time. The reduction of manpower and time for developing products is expected by changing the process of quality improving in software developing from man-powered handwork system into automatic test case generation based on API of source code.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.6
• /
• pp.127-135
• /
• 2010

As logistics facilities have a high ceiling height, simple structure, and the need for a quick return on investment, it is usually essential to advance the construction schedule of such facilities. Accordingly, PC structures, which require less labor, cost and schedule, can be more competitive than RC structures. However, most construction companies in Korea are familiar with RC structure design, have negative perceptions regarding PC structures, and do not sufficiently adopt new construction techniques. The structure that this research features has 110 columns that are 14 m high and are built to the same specification, and applying an RC design to the structure will lead to issues related to constructibility, economic viability, project duration and safety. Therefore, this study intends to feature PC design as an alternative to the RC warehouse design, and perform a comparative analysis of the reduction in labor, cost and construction schedule to highlight benefits. The research outcomes herein will provide inputs to subsequent studies on new construction strategies to advance the construction schedule, improve quality and constructibility, enhance safety and save costs.

• Journal of Environmental Health Sciences
• /
• v.36 no.5
• /
• pp.391-401
• /
• 2010

A reduction in risk of occupational exposure to chemical hazards within the workplace has been the focus of attention both through industry initiatives and legislation. The aims of this study were to develop an exposure matrix by industry and process, and to apply this matrix to control the risk of occupational exposure to Dichloromethane (DCM). The exposure matrix is a tool to convert information on industry and process into information on occupational risk. The exposure matrix comprised industries and processes involving DCM, based on an exposure database provided by KOSHA (the Korean Occupational Safety and Health Agency), which was gathered from a workplace hazards evaluation program in Korea. The risk assessment of the exposure matrix was performed using Hallmark risk assessment tool. The results of the risk assessment were indicated by a Danger Value (DV) calculated from the combination of hazard rating (HR), duration of use rating (DUR), and risk probability rating (RPR) of exposure to the chemical, and were divided into four control bands which were related to control measures. The applicability of the risk assessment of the exposure matrix was evaluated by a field study, and survey of the employees of the exposure matrix groups. Among 45 industries examined, this study found that greater attention should be paid to two industries: the manufacture of other optical instruments and photographic equipment, and the manufacture of printing ink, and to one process among 47 examined, the packing process in the manufacture of printing ink, because these were regarded as carrying the highest risk. This tool of a risk assessment for the exposure matrix can be applied as a general exposure information system for hazard control, risk quantification, setting the occupational exposure limit, and hazard surveillance. The exposure matrix includes workforce data, and it provides information on the numbers of exposed workers in Korea by agent, occupation, and level of exposure and risk.

• The Korean Journal of Pain
• /
• v.20 no.2
• /
• pp.116-122
• /
• 2007

Background: Lumbar zygapophysial joints are a common source of chronic lower back pain and radiofrequency thermocoagulation (RF) of the medial branches (MB) has been shown to be effective at providing substantial pain relief for chronic low back pain. Therefore, we carried out this study to determine the short term outcomes and prognostic factors of RF on the MB of patients with lumbar facet syndrome. Methods: We performed RF in fourteen patients who showed greater than 80% pain relief up to three times after a diagnostic MB block was conducted using 0.3 ml of 0.5% bupivacaine. Using 10 cm curved electrodes with 10-mm active tip, a 60 second, $80^{\circ}C$ lesion was made after electrical stimulation at 50 Hz for sensory and 2 Hz for motor nerve testing. The degree of pain relief was then assessed after 2 weeks, and again after 3 months using a visual analog scale (VAS) and a four point Likert scale. The outcome was regarded as 'success' if at least a 50% reduction in the VAS was observed. Possible prognostic factors between the two groups were also evaluated Results: The success rate was 71.4% (10/14) after three months of follow-up. However, there were transient complications, such as neuritis like syndrome, in 4 patients. In addition, short symptom duration and low minimal voltage (< 0.4 V) for sensory stimulation were shown to be the relevant prognostic factors for a successful outcome. Conclusions: RF may be an alternative to repeated MB block or intraarticular injection for palliation of lumbar facet syndrome. For better outcomes, early diagnosis and strict patient selection should be coupled with efforts to avoid anatomically incorrect RF.

• Clinics in Shoulder and Elbow
• /
• v.10 no.2
• /
• pp.220-226
• /
• 2007

Purpose: The distal clavicle has a biomechanical structure different from that of the proximal or middle 1/3 clavicle, and delayed union or nonunion occurs frequently in a distal clavicle fracture. The authors obtained favorable results from an open reduction and bone grafting of the distal clavicle nonunion. We report the results together with review of the relevant literature. Materials and Methods: The subjects were 8 patients(average age, 38.9) who had undergone surgery for distal clavicle nonunion from August 2003 to May 2006. Nonunion occurred after surgical treatment in 4 cases, and after conservative treatment in the other 4. In all cases, the patients complained of pain. Results: The mean follow-up duration was 14 months, and radiological union was observed in 8 weeks on average. In all cases, the range of shoulder joint motion was normal at the end of the follow-up observation. In the functional evaluation, 7 cases showed excellent results and 1 case showed good results. Conclusion: Surgical treatment is a safe and reliable treatment for distal clavicle fracture nonunion because it can achieve early rehabilitation and union.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.10C
• /
• pp.995-1006
• /
• 2003

It is well know that in the wireless communication systems the transmitted signals can suffer from multipath fading due to the wave propagation characteristics and the obstacles over the paths, resulting in serious reduction in the power of the received signals. However, it is possible to take advantage of the inherent diversity imposed in the multipath reception if the underlying channel can be properly estimated. One of the diversity reception methods in this case is Rake processing. In this paper we study the Rake receivers for the direct-sequence spread-spectrum communication systems utilizing PN (pseudo noise) sequences to achieve spread spectrum. A conventional Rake receiver can use the finite-duration impulse (FIR) filter followed by the PN sequence demodulator, where the FIR filter coefficients are the reverse-ordered complex conjugate values of the fading channel impulse response estimates. Here, we propose a new Rake processing method by replacing the aforementioned PN code sequence with a new set of optimum demodulator coefficients. More specifically, the concept of the new optimum Rake processing is first introduced and then the optimum demodulator coefficients are theoretically derived. The performance obtained using the new optimum Rake processing is also calculated. The analytical results are verified by computer simulation. As a result, it is shown that the new optimum Rake processing method improves the MSE performance more than 10 dB over the conventional one using the fixed PN sequence demodulator. It is also shown that the new optimum Rake processing method improves the MSE performance about 10 dB over the Adaptive Correlator that performs the combining of the multipath components and PN demodulation concurrently. And finally, the MSE performance of the optimum Rake demodulator is very close to the MSE performance of OPSK demodulator under the AWGN channel.

• Korean Journal of Food Science and Technology
• /
• v.34 no.4
• /
• pp.631-636
• /
• 2002

Lethality of high intensity light pulse on the pre-determined microbial populations has been investigated. Prior to the treatment, Lactobacillus plantarum, Lactobacillus brevis, Leuconostoc mesenteroides and Pediococcus pentosaceus were cultivated separately onto the surface of Lactobacilli MRS agar. Pre-determined microbial populations were applied to the test media and these sample were exposed to high intense light source with an exposure time ranging from 1 to $2500\;{\mu}s$. Results showed that at least 200 light pulses of $1\;{\mu}s$ duration were required to reduce L. Plantarum cells by 90% at 25 kV, the greater the number of light pulses, the larger the reduction in viable cell numbers. Viable cells of L. plantarum and the others were reduced by more than 5 and 6 log cycles at the upper exposure level of $750\;{\mu}s$, respectively. These study shows that pulsed light emissions can significantly reduce populations of lactic acid bacteria on exposed surface with exposure times. Killing efficiency for L. plantarum significantly increased with decreasing the distance between the lamp and the surface of samples.

• Biomaterials Research
• /
• v.22 no.4
• /
• pp.328-336
• /
• 2018

Background: Biogenic fabrication of silver nanoparticles from naturally occurring biomaterials provides an alternative, eco-friendly and cost-effective means of obtaining nanoparticles. It is a favourite pursuit of all scientists and has gained popularity because it prevents the environment from pollution. Our main objective to take up this project is to fabricate silver nanoparticles from lichen, Usnea longissima and explore their properties. In the present study, we report a benign method of biosynthesis of silver nanoparticles from aqueous-ethanolic extract of Usnea longissima and their characterization by ultraviolet-visible (UV-vis), Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (TEM) and scanning electron microscopy (SEM) analyses. Silver nanoparticles thus obtained were tested for antimicrobial activity against gram positive bacteria and gram negative bacteria. Results: Formation of silver nanoparticles was confirmed by the appearance of an absorption band at 400 nm in the UV-vis spectrum of the colloidal solution containing both the nanoparticles and U. longissima extract. Poly(ethylene glycol) coated silver nanoparticles showed additional absorption peaks at 424 and 450 nm. FTIR spectrum showed the involvement of amines, usnic acids, phenols, aldehydes and ketones in the reduction of silver ions to silver nanoparticles. Morphological studies showed three types of nanoparticles with an abundance of spherical shaped silver nanoparticles of 9.40-11.23 nm. Their average hydrodynamic diameter is 437.1 nm. Results of in vitro antibacterial activity of silver nanoparticles against Staphylococcus aureus, Streptococcus mutans, Streptococcus pyrogenes, Streptococcus viridans, Corynebacterium xerosis, Corynebacterium diphtheriae (gram positive bacteria) and Escherichia coli, Klebsiella pneuomoniae and Pseudomonas aeruginosa (gram negative bacteria) showed that it was effective against tested bacterial strains. However, S. mutans, C. diphtheriae and P. aeruginosa were resistant to silver nanoparticles. Conclusion: Lichens are rarely exploited for the fabrication of silver nanoparticles. In the present work the lichen acts as reducing as well as capping agent. They can therefore, be used to synthesize metal nanoparticles and their size may be controlled by monitoring the concentration of extract and metal ions. Since they are antibacterial they may be used for the treatment of bacterial infections in man and animal. They can also be used in purification of water, in soaps and medicine. Their sustained release may be achieved by coating them with a suitable polymer. Silver nanoparticles fabricated from edible U. longissima are free from toxic chemicals and therefore they can be safely used in medicine and medical devices. These silver nanoparticles were stable for weeks therefore they can be stored for longer duration of time without decomposition.