• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.387-394
• /
• 2016

This paper presents a fully digital delay locked loop (DLL) that can acquire lock in four clock cycles with a resolution of a 1/4 NAND-delay. The proposed DLL with a multi-dither-free phase detector acquires the initial lock in four clock cycles with 1/2 NAND-delay. Then, it utilizes a multi-dither-free phase detector, a region accumulator, and phase blenders, to improve the resolution to a 1/4 NAND-delay. The region accumulator which continuously steers the control registers and the phase blender, adaptively controls the tracking bandwidth depending on the amount of jitter, and effectively suppresses the dithering jitter. Fabricated in a 65 nm CMOS process, the proposed DLL occupies $0.0432mm^2$, and consumes 3.7 mW from a 1.2-V supply at 2 GHz.

• Journal of Power Electronics
• /
• v.14 no.5
• /
• pp.815-826
• /
• 2014

An improved bridgeless interleaved boost power factor correction (PFC) rectifier to improve power efficiency and component utilization is proposed in this study. With combined conventional bridgeless PFC circuit and interleaved technology, the proposed rectifier consists of two interleaved and magnetic inter-coupling boost bridgeless converter cells. Each cell operates alternatively in the critical conduction mode, which can achieve the soft-switching characteristics of the switches and increase power capacity. Auxiliary blocking diodes are employed to eliminate undesired circulating loops and reduce current-sensing noise, which are among the serious drawbacks of a dual-boost PFC rectifier. Magnetic component utilization is improved by symmetrically coupling two inductors on a unique core, which can achieve independence from each other based on the auxiliary diodes. Through the interleaved approach, each switch can operate in the whole line cycle. A simple control scheme is employed in the circuit by using a conventional interleaved controller. The operation principle and theoretical analysis of the converter are presented. A 600 W experimental prototype is built to verify the theoretical analysis and feasibility of the proposed rectifier. System efficiency reaches 97.3% with low total harmonic distortion at full load.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.5
• /
• pp.543-551
• /
• 2007

The performance characteristics of water-chilling heat pump using $CO_2$ with respect to variation of inlet temperature and mass flow rate of secondary fluid was investigated experimentally. An experimental apparatus is consisted of a compressor, a gas cooler, an expansion valve, an evaporator and a liquid receiver. All heat exchangers used in the test rig are counter-flow-type heat exchangers with concentric dual tubes, which ate made of copper. The gas cooler and the evaporator consist of 6 and 4 straight sections respectively arranged in parallel, each has 2.4 m length. The experimental results were summarized as the followings : As inlet temperature of secondary fluid in the gas cooler increases from $10^{\circ}C$ to $40^{\circ}C$, the compressor work, heating capacity and heating COP were varied to 37.8%, -13%, -35.9%, respectively. The heating capacity, compressor work, heating COP were turned into 23.3%, 6.42%, 13.1%, respectively when ass flow rate of secondary fluid in the evaporator increases from 70 g/s to 150 g/s. The above tendency is similar with performance variation with respect to temperature variation of secondary fluid in the conventional vapor compression cycle.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.27-32
• /
• 2008

The present study has been conducted economic analysis of heat storage type ground source heat pump system(HSGSHP) and normal ground source heat pump (GSHP) which are installed at the same building in the shared an apartment house. Cost items, such as initial cost, annual energy cost and maintenance cost of each system are considered to analyze life cycle cost (LCC) and simple payback period (SPP) with initial cost different are compared. The initial cost is a rule to the Government basic unit cost of production. LCC applied present value method is used to assess economical profit of both of them. Variables used to LCC analysis are prices escalation rate and interest rate mean values of during latest 10 years. The LCC result shows that HSGSHP (1,050,910,000won) is more profitable than GSHP by 68.9% initial cost. And SPP appeared 3.0 year overcome the different initial cost by different annual energy cost.

• Proceedings of the Korean Information Science Society Conference
• /
• 2003.10a
• /
• pp.196-198
• /
• 2003

Virtually every digital signal processors(DSPs) support on-chip multi- memory banks that allow the processor to access multiple words of data from memory in a single instruction cycle. Also, all existing fixed-point DSPs have irregular architecture of heterogeneous register which contains multiple register files that are distributed and dedicated to different sets of instructions. Although there have been several studies conducted to efficiently assign data to multi-memory banks, most of them assumed processors with relatively simple, homogeneous general-purpose resisters. Therefore, several vendor-provided compilers fer DSPs were unable to efficiently assign data to multiple data memory banks. thereby often failing to generate highly optimized code fer their machines. This paper presents an algorithm that helps the compiler to efficiently assign data to multi- memory banks. Our algorithm differs from previous work in that it assigns variables to memory banks in separate, decoupled code generation phases, instead of a single, tightly-coupled phase. The experimental results have revealed that our decoupled algorithm greatly simplifies our code generation process; thus our compiler runs extremely fast, yet generates target code that is comparable In quality to the code generated by a coupled approach

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.325-329
• /
• 1996

We report on p-type arsenic doping of metalorganic vapor phase epitaxially (MOVPE) grown HgCdTe on (100) GaAs. HgCdTe was grown at $370^{\circ}C$ in a horizontal reactor with using dimethy-cadmium, diisoprophyltelluride, and elemental Hg. We used tris-dimethylaminoarsenic (DMAAs) as the metalorganic for p-doping. 4micron thick CdTe and subsequently 10micron thick HgCdTe were grown on (100) GaAs substrate. Interdiffused multilayer process in which thin CdTe and HgTe layers are grown alternately and interdiffused to obtain homogeneous HgCdTe alloys was used. Arsenic was doped during CdTe growth cycle. After growth HgCdTe was annealed at $415^{\circ}C$ for 15 min and then annealed again at $220^{\circ}C$ for 3 hr, both with Hg-saturate condition. We could obtain p-doping from 2.5$\times$$10^{16}$ to 6.6$\times$$10^{17}$$cm^{-3}$, depending on the DMAAs partial pressure. With the dual Hg-annealing, activation of arsenic was aboutt 90%, which was confirmed by SIMS measurement. With only low temperature annealing at $220^{\circ}C$ for 3hr, activation efficiency was about 50%.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.2
• /
• pp.271-279
• /
• 2018

During the seven years from 2009 to 2016, PWR SNF (spent nuclear fuel) transportation and storage systems suitable for domestic conditions were developed by the government to cope with the saturation of wet storage capacity in NPPs. One of the developed systems is a multipurpose metal cask applicable for transportation/storage; the other is a concrete cask dedicated to storage. Efficient cask technologies were secured utilizing the characteristics and experience of relevant industrial, academic and research institutes. Technological independence was also achieved through several patent registrations of research outcomes. To prepare for a rapid increase of demand in the near future, technology transfer of secured patents and technologies to the domestic industry was carried out twice in the years of 2016 and 2017.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.326-329
• /
• 2008

DARPA's hypersonic propulsion program VULCAN is aimed for development of Mach 4+ capable engine by combining current production turbofan engine such as F119 with CVC (Constant Volume Combustion) engine. Final goal is a TBCC(Turbo-based Combined Cycle) engine by combining with dual mode ramjet/scramjet engine. CVC is a common designation of new concept of high efficiency engines, such as Pulse Detonation Engine (PDE) or Continuous Detonation Engine (CDE), which use the detonation as a combustion mechanism. Present paper introduces the internationally collaborative research activities carried out in Aerospace Combustion and Propulsion Laboratory of the department of Aerospace Engineering of the Pusan national University.

• Journal of the Korea Society for Simulation
• /
• v.24 no.3
• /
• pp.17-26
• /
• 2015

A cluster tool used in many kinds of semiconductor processes for improving the performance and the quality of wafers has a simple configuration, but its schedule is not easy because of its parallel processing module, a lack of intermediate buffers, and time constraints. While there have been many studies on its schedule, most of them have focused on full cycles in which identical work cycles are repeated under constant task times. In this research, we suggest strategies of start-up transient scheduling which satisfies time constraints and converges into a desirable steady schedule for full work cycle. The proposed schedules are expected robust under the stationary stochastic task times. Finally, we show that the strategies make schedules enters the desirable steady schedule and robust using the simulation.

• Journal of the Korean Society of Food Culture
• /
• v.36 no.3
• /
• pp.284-292
• /
• 2021

The food service industry has grown larger with changes in the economic and socio-cultural environment. In this saturated food service industry, generation X and MZ are the main consumer forces that demand attention. That is because a generation is the main psychographic factor that reflects personal values and lifestyle based on one's life cycle. From such a perspective, a generation in marketing has been used as a variable to predict a market by supplementing demographic factors. Accordingly, this study classified generations into generation X and generation MZ with the use of the 2019 consumer behavior survey for food by Korea Rural Economic Institute (KREI) and then investigated the factors influencing group and personal dining-out expenses. The analysis was carried out applying the Tobit model using SPSS and R. The positively influential variables on generation X's personal dining-out expenditure were male, single person, high income and simple lifestyle, whereas housewives, personal ethical consciousness, behavioral ethical consciousness, and safe dietary life were negatively influential variables. The positively influential variables on generation MZ's personal dining-out expenditures were male, dual-income, high education level, corporate and governmental ethical consciousness, while the number of family members and safe dietary life were negatively influential variables.