• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.50-57
• /
• 2004

This study attempted to evaluate the water repellency and drying effectiveness of linseed oil treated-solid wood at high temperature by immersion. The moisture content of green wood (Pinus densiflora) sample (above 90%) was reduced about 10% after 6 hours treatment at 150℃. When the treated samples were cut into cross section along the length, it was observed that the linseed oil penetrated into up to 20% of the sample cross section area in all locations. However, a strength loss of the specimen was not detected. The pre-drilling before linseed oil treatment was effective in reducing the defects such as checks and splits, and improved the linseed oil penetration into all samples from the surfaces. The result of water absorption test of treated-wood showed that the water repellent efficacy of treated-wood was greater than that of the control. The anti-fungal activity of treated samples using five sap stains and thee decay fungi was not detected in broad-spectrum toxic mechanism. However, decay test using white rot fungi (Tyromyces palustris) and brown rot fungi (Trametes versicolor) showed that the treated sample has a decay resistance to these two fungi.

• Macromolecular Research
• /
• v.9 no.5
• /
• pp.267-276
• /
• 2001

In order to endow with new bioactive functionality from demineralized bone particle (DBP) as natural source to poly(L-lactide) (PLA) synthetic biodegradable polymer, porous DBP/PLA as natural/synthetic composite scaffolds were prepared and compared by means of the emulsion freeze drying and solvent casting/salt leaching methods for the possibility of the application of tissue engineered bone and cartilage. For the emulsion freeze drying method, it was observed that the pore size decreased in the order of 79$\mu\textrm{m}$ (PLA control) > 47$\mu\textrm{m}$ (20% of DBP) > 23 $\mu\textrm{m}$ (40% of DBP) > 15$\mu\textrm{m}$ (80% of DBP). Porosities as well as specific pore areas decreased with increasing the amount of DBR. It can be explained that DBP acts like emulsifier resulting in stabilizing water droplet in emulsion. For the solvent casting/salt leaching method, a uniform distribution of well interconnected pores from the surface to core region were observed the pore size of 80 ∼70 $\mu\textrm{m}$ independent with DBP amount. Porosities as well as specific pore areas also were almost same. For pore size distribution by the mercury intrusion porosimeter analysis between the two methods, the pore size distribution of the emulsion freeze drying method was broader than that of the solvent casting/salt leaching method due to the mechanism of emulsion formation. Scaffolds of PLA alone, DBP/PLA of 40 and 80%, and DBP powder were implanted on the back of athymic nude mouse to observe the effect of DBP on the induction of cells proliferation by hematoxylin and eosin staining for 8 weeks. It was observed that the effect of DBP/PLA scaffolds on bone induction are stronger than PLA scaffolds, even though the bone induction effect of DBP/PLA scaffold might be lowered than only DBP powder, that is to say, in the order of DBP only > DBP/PLA scaffolds of 40 and 80% DBP > PLA scaffolds only for osteoinduction activity. In conclusion, it seems that DBP plays an important role for bone induction in DBP/PLA scaffolds for the application of tissue engineering area.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.1
• /
• pp.35-39
• /
• 2016

The flexible and superhydrophobic properties of silica aerogels are extremely important material for thermal insulation and oil spill cleanup applications for their long-term use. Flexible silica aerogels were synthesized by using a two-step sol-gel process with precursors, methyltrimethoxysilane (MTMS) followed by supercritical drying. Silica aerogels were prepared at different molar ratio of methanol to MTMS (M). It was observed that the silica aerogels prepared at M=28 were monolithic but inelastic in nature, however, for M=35, the obtained aerogels were monolithic, elastic in nature with less shrinkage. The microstructural studies were carried out using scanning electron microscopy and surface area measurements. The hydrophobicity was confirmed by Fourier transform Infrared spectroscopy and water contact angle measurements. The detailed insight mechanism for flexible nature of silica aerogels and hydrophobic behavior were studied.

• Current Photovoltaic Research
• /
• v.2 no.1
• /
• pp.36-39
• /
• 2014

Formation mechanism of residual carbon layer, frequently observed in the $CuInSe_2$ (CIS) thin film prepared by direct solution coating routes, was investigated in order to find a way to eliminate it. As a model system, a methanol solution with dissolved Cu and In salts, whose viscosity was adjusted by adding ethylcellulose (EC), was chosen. It was found that a double layer, a top metal ion-derived film and bottom EC-derived layer, formed during an air drying step presumably due to different solubility between metal salts and EC in methanol. Consequently, the top metal ion-derived film acts as a barrier layer inhibiting further thermal decomposition of underlying EC, resulting a formation of bottom carbon residue layer.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.7 s.250
• /
• pp.779-786
• /
• 2006

Woven sisal textile reinforced composites were manufactured to evaluate fracture toughness, and tensile test. All specimens were immersed in water five times. All specimens are immersed in pure water during 9 days at room temperature, and dried in 1 day at $50^{\circ}C$. Two kinds of polymer matrices such as epoxy and vinyl-ester were used. Fractured surface were investigated to study the failure mechanism and fiber/matrix interfacial adhesion. It is shows that it can be enhanced to improve their mechanical performance to reveal the relationship between fracture toughness and water absorption fatigue according to different polymer matrices. Water uptake of the epoxy composites was found to increase with cycle times. Mechanical properties are dramatically affected by the water absorption cycles. Water-absorbed samples observed poor mechanical properties such as lower values of maximum strength and extreme elongation. The $K_{IC}$ values demonstrate a decrease in inclination with increasing cyclic times of wetting and drying fur the epoxy and vinyl-ester.

• Korean Journal of Environmental Agriculture
• /
• v.19 no.5
• /
• pp.442-449
• /
• 2000

The bioremediation is an economic technology to remove the organopollutants from soil. It is often found that the remediation could not remove the compounds below the levels determined by vigorous extractions as required by regulatory agencies. The reason for the reduced bioavailability with increasing time of aging has been accredited to the sequestration of the compounds in remote sites within or between soil particles. Then, the aging could be defined as the time-dependent sequestration. Partitioning and entrapment have been suggested as mechanism for aging. The rate and extent of the sequestration varies among dissimilar soils. The bioavailability of aged pollutants in soil could be measured by bioassays, mild solvent extraction, and soild-phase extractions. The sequestration could be affected by many factors including various soil properties, wetting and drying cycle, and the presence of cosolutes and NAPLs etc. The bioavailability and sequestration should be considered to determine the environmentally acceptable endpoint.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.3
• /
• pp.52-59
• /
• 2004

The greater Increase of the demand for environmental friendly materials especially for packaging industry leads to the larger interest in the reusable and recycable materials such as pulp mold. Although the pulp mold has great characteristics for packaging, some deficiency compared with other packaging material like EPS(Expandable Polystyrene) need to be overcome, for example, the relative higher cost. In this report, since the water drainage rate at the forming zone of a wet pulp mold process could have a great influence on the economical efficiency not only by increasing machine speed but also reducing the drying energy, the optimum ways for increasing drainage were investigated The mechanism of vacuum drainage In pulp mold forming was successfully evaluated by using RDA(Retention and Darinage Analyzer). Since the conditions of stock were greatly affected by the pulping time of low consistency pulper, the optimum pupling time was investigated with considerations of all stock preparation processes. The change of stock temperature and the addition of polyelectrolyte could improve the vacuum drainage rate. It was founded that the wire mesh types of mold former had a little influence on the retention because of the relatively mild vacuum drainage. However, the bigger size of dewatering hole showed better drainage rate and could reduce the plugging and con lamination of mold.

• Fisheries and Aquatic Sciences
• /
• v.8 no.1
• /
• pp.10-16
• /
• 2005

Conditions for sufficient and rapid distribution of a cryoprotectant (sorbitol solution) into intact fish muscle (Oncorhynchus mykiss) were studied as changing in the residual Ca2+ ATPase activity during freeze/thaw cycling. Chunks of the fish muscle were immersed in 4 concentrations of sorbitol solutions ($20\%$, $30\%$, $45\%$, and $60\%$) by a shaker mechanism at 5$^${circ}C. Whole immersion samples (W) showed a higher value of the residual Ca2+ ATPase activity than those in the untreated controls (C), except in the treated controls (TC), while less effect of immersion concentration could be found. Comparing the extent of penetration of sorbitol into the surface layer to inner layer of immersed fish chunks, outer portion samples achieved excellent cryoprotection with $100\%$ of the residual ATPase activity values or more. For the inner portion samples, $30\%$ and $45\%$ sorbitol solution treatments indicated a higher ATPase activity than $60\%$ treatment. At high concentrations, mass transfer rates during osmotic dehydration might berapid and it causes faster surface drying by dewatering at surface solute layer. Periodically immersed and relaxed samples, W (5-3-1), led to good cryoprotection effect: W (5-3-1) indicated high residual Ca2+ ATPase activity values and the residual ATPase activity values excess $100\%$ in immersion of $30\%$ and $45\%$ sorbitol solutions.

• Journal of the Korean Ceramic Society
• /
• v.40 no.8
• /
• pp.791-797
• /
• 2003

The special binding mechanism developed provides higher density, lower porosity and higher strengths compared with conventional castables. $\rho$-alumina was employed as a binder materials and nano-sized clay colloidal was added to enhance the drying strength preparing for the alumina vibrated castable. Lower water requirement for casting results in a denser product. The mechanical properties with dimensional stability and corrosion resistance behaviors have been improved by controlling the matrix compositions of the castable. The modulus of rupture and compressive strength after heat treatment at 150$0^{\circ}C$ are 92.34 kgf/$\textrm{cm}^2$ and 370 kgf/$\textrm{cm}^2$ respectively. The activation energy of mullite formation is 11.47 kcal/mol.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.11b
• /
• pp.50-55
• /
• 1999

Sizing development of AKD-sized paper by beta-ketoester formation has been debated until recent years because of absence of its obvious and direct spectroscopic evidence. In this study, reaction between AKD and cellulose was investigated to disclose the possibility of beta-ketoester formation between two components under no catalyzed neutral condition. In absence of water, AKD reacted with cellulose to form beta-ketoester linkage under no catalyzed neutral condition, while, in presence of water, most of AKD was hydrolyzed to a dialkyl ketone or beta-ketoacid. Therefore, the main mechanism of AKD sizing would not be the formation of beta-ketoester between AKD and cellulose in the papermaking process. It could be suggested that the sizing development of AKD-sized paper is obtained by next two mechanisms: 1) formation of a thin-layer of AKD on the fiber surface through melting and spreading of AKD emulsion particles by heat, and 2) the formation of ketone by the hydrolysis of AKD during drying and storage of AKD-sized papers.