• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.513-520
• /
• 2017

The application possibility of an alternative new method with low energy consumption was studied for the eco-friendly fabrication of foamed glasses from waste glasses. As a result, fabricating temperature can be reduced under $300^{\circ}C$ without using various expensive inorganic oxidants. The foamed glass can be fabricated at a proper mixing ratio of the waste glass powder, water glass, little surfactant and bubble stabilizer by induction heating method. In the experimental range, the assured optimal condition is 4 min heating on the induction machine with a steel-container ($100mm{\times}100mm{\times}20mm$) and followed by evaporating and drying process for 11 min with 110 g of glass powder, 80 g of water glass, 3 g of surfactant and 0.2 g of bubble stabilizer. When the foamed glass was fabricated at the optimal condition, the density of the glass was $0.85g/cm^3$ and the heat conduction was $0.052W/h{\cdot}K$. In addition, the compressive strength of the glass was above $50kg/cm^2$.

• Korean Chemical Engineering Research
• /
• v.55 no.1
• /
• pp.1-6
• /
• 2017

More addition of calcium carbonate in printing paper allows savings of the wood fibers and the drying energy. Pre-flocculation of GCC (ground calcium carbonate) using functional polymers was known as the best available technology to make high loaded paper until now, and it allowed less reduction of the paper essential properties such as tensile strength and smoothness at higher GCC content. However, pre-flocculated GCC became unstable in size under the continued agitation in the mill. Therefore, pre-flocculation method was modified in such a way that the in-situ calcium carbonate was formed between the GCC particles of the pre-flocculated GCC, and the resultant became more stable in size, which we named as HCC (hybrid calcium carbonate). HCC turned out to make high tensile strength and smoothness as much as the pre-flocculated GCC and gave much better size stability against stirring. Furthermore, HCC gave high bulk that pre-flocculation could not make.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.1
• /
• pp.1-7
• /
• 2011

Nanocomposites of reduced graphene oxide and manganese (II,III) oxide can be synthesized by the freeze-drying process of the mixed colloidal suspension of graphene oxide and manganese oxide, and the subsequent heat-treatment. The calcined reduced graphene oxide-manganese (II,III) oxide nanocomposites are X-ray amorphous, suggesting the formation of homogeneous and disordered mixture without any phase separation. The reduction of graphene oxide to reduced graphene oxide upon the heat-treatment is evidenced by Fourier-transformed infrared spectroscopy. Field emission-scanning electronic microscopy and energy dispersive spectrometry clearly demonstrate the formation of porous structure by the house-of-cards type stacking of reduced graphene oxide nanosheets and the homogeneous distribution of manganese ions in the nanocomposites. According to Mn K-edge X-ray absorption spectroscopy, manganese ions in the calcined nanocomposites are stabilized in octahedral symmetry with mixed Mn oxidation state of Mn(II)/Mn(III). The present reduced graphene oxide-manganese oxide nanocomposites show characteristic pseudocapacitance behavior superior to the pristine manganese oxide, suggesting their applicability as electrode material for supercapacitors.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.739-744
• /
• 2011

Activated carbon SCR(CSCR) catalyst that is used to remove $NO_x$ in exhaust gas including boron discharged from the production process of liquid crystal display(LCD) shows deactivation when boron is deposited to block the pores within the catalyst or to cover its active sites. The spent carbon catalyst is regenerated by washing with various surfactants, drying and calcination. For comparison of the physical and chemical properties before and after the regeneration with the variables, type of surfactants and calcination condition, element analysis by ICP, $N_{2}$ adsorption were conducted. $DeNO_{x}$ in SCR with $NH_3$ was carried out in a fixed bed reactor at $120^{\circ}C$. The activated carbon catalyst regenerated through washing with a non-ionic surfactant in $H_{2}O$ at $90^{\circ}C$ and calcination under $N_{2}$ gas at $550^{\circ}C$ shows similar level of surface area and $NO_x$ removal efficiency with those of fresh catalyst.

• Korean Journal of Food Science and Technology
• /
• v.11 no.3
• /
• pp.192-199
• /
• 1979

With cells of Streptomyces spp K-45 isolated from soil, the immobilization of glucose isomerase by a series of treatments ; heat, carefully manipulated drying, extrusion with a thickening agent, and glutaraldehyde-induced crosslinking, was presented. This was aimed to obtain a mechanically stable form of whole cell containing glucose isomerase. The resulted pellet form had a good mechanical strength, compared with a commercial product, and showed 26 % of the activity recovery. The specific activity was 48.1 units per g of the dry material. The immobilized glucose isomerase generally showed properties similar to those of the soluble enzyme ; optimal pH at $7.5{\sim}9.0$, optimal temperature at $80{\sim}85^{\circ}C$, activation energy of 10.9 kcal/mole, and $K_m$ for glucose of 10.9M. The immobilized enzyme was very thermostable and pH stable.

• Korean Journal of Microbiology
• /
• v.5 no.2
• /
• pp.79-85
• /
• 1967

Kim, Jong Hyup., (Div. of Biology, Atomic Energy Research Institute,Korea.;) Studies on the Cellulor Metabolism in Microorganisms as influenced by Gamma-irradiation(III): On the Changes of Free Amino acid Pool and content of Protein in Yeast clls irradiated by .gamma.-ray. 1. The strain of Saccharomyces cerevisiae had been cultured synchronously in aerobic condition and irradiatel by gamma-ray from the source of cobalt-60. Drying in vacuum oven at $90^{\circ}C$ C over 12 hours, then changes of protein content (Kjeldahl) and free amino acid pool have been assayed with use of spectrophotometer. Results obtained were compared with those of unirradiated normal cells. 2. It is proved that amount of protein content in the irradiated cells increases to seven percent more than those of normal cells in the same weight of dried samples. It seems like carbohydrate breakown had been stimulated by irradiation and that relative contents of protein shows higher values than those of normal in the same weight of samples. 3. The amount of free amino acid pool in the irradiated cells shows less value about ten percent than those of normal cells, and rate of decreasing is also weak than those of standard reagent solution of amino acid. We may assume that free amino acid pool would be protected against radiation damage in living cells and more stable than in vitro. 4. The component of free amino acid pool have been assayed on second dimensional paper chromatogram, and the identified amino acids are as follows; aspartic acid, serine, glutamic acid, cystine, lysine, glycine, threonine, histidine, arginine, tyrosine, phenylalanine, valine and leucine. 5. Distributional presence of free amino acids are identical to that of normal cells except arginine, it is cosumable that radiation effect is univerlsal to all amino acid. However it is obvious that there are differences in radiolabilities of amino acids in irradiated cells.

• Journal of the Korean Ceramic Society
• /
• v.56 no.3
• /
• pp.211-232
• /
• 2019

Porous ceramics are promising materials for a number of functional and structural applications that include thermal insulation, filters, bio-scaffolds for tissue engineering, and preforms for composite fabrication. These applications take advantage of the special characteristics of porous ceramics, such as low thermal mass, low thermal conductivity, high surface area, controlled permeability, and low density. In this review, we emphasize the direct foaming method, a simple and versatile approach that allows the fabrication of porous ceramics with tailored microstructure, along with distinctive properties. The wet foam stability is achieved under the controlled addition of amphiphiles to the colloidal suspension, which induce in situ hydrophobization, allowing the wet foam to resist coarsening and Ostwald ripening upon drying and sintering. Different components, like contact angle, adsorption free energy, air content, bubble size, and Laplace pressure, play vital roles in the stabilization of the particle stabilized wet foam to the porous ceramics. The mechanical behavior of the load-displacements curves of sintered samples was investigated using Herzian indentations testes. From the collected results, we found that microporous structures with pore sizes from 30 ㎛ to 570 ㎛ and the porosity within the range from 70% to 85%.

• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.115-120
• /
• 2015

$K_2CO_3$-based dry regenerable sorbents were prepared by spray-drying techniques to improve mass produced $K_2CO_3-Al_2O_3$ sorbents (KEP-CO2P, hereafter), and then tested for their $CO_2$ sorption capacity by a $2,000Nm^3/h$ (0.5 MWe) $CO_2$ capture pilot plant built for Unit 3 of the Hadong thermal power station in 2010. Each of the sample sorbents contained 35 wt.% $K_2CO_3$ as the active materials with various support materials such as $TiO_2$, MgO, Zeolite 13X, $Al_2O_3$, $SiO_2$ and hydrotalcite (HTC). Their physical properties and reactivity were tested to evaluate their applicability to a fluidized-bed or fast transport-bed $CO_2$ capture process. The $CO_2$ sorption capacity and percentage utilization of $K_2CO_3$-MgO based sorbent, Sorb-KM2, was $8.6g-CO_2/100g$-sorbents and 90%, respectively, along with good mechanical strength for fluidized-bed application. Sorbs-KM2 and KT were almost completely regenerated at $140^{\circ}C$. No degradation of Sorb-KM by $SO_2$ added as a pollutant in flue gas was observed during a cycle test.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.1-7
• /
• 2012

The increase of OCC solid content after wet pressing will save drying energy greatly. We applied spacers, which used to increase draining rate and bulk in fiber furnishes, to increase the OCC solid contents. MDF fibers (fibers for making medium density fiberboard) and diatomaceous earth were used as spacers, and added 10% by weight to the OCC fiber furnish. Application of high wet pressing pressure to the mixed furnish of spacers and refined OCC did not deteriorate bulk and drainage rate, but their solid contents were increased to 0.5-1.5% without loss of compressive strength when compared to those of unrefined OCC, which is the furnish normally used for mill commercial practice. It is believed that the spacers caused the rate of solid content increase faster in the mixed furnish with OCC at high wet pressing pressure area than the unrefined OCC furnish did. Little amount of starch addition (0.5%) to the spacers helped to keep the strength properties.

• Korean Journal of Food Science and Technology
• /
• v.12 no.2
• /
• pp.82-87
• /
• 1980

The red color bleaching phenomena of red pepper powder by the exposure to sun light were studied on the various factors such as drying methods of pepper and the storage conditions of pepper powder, relative humidities, particle sizes, and the amounts and qualities of light. The surface color of red pepper was rapidly bleached by the successive daily exposures until the color retention value (capsanthin remained/original capsanthin content) reached to 0.5, while that of dark storge showed a negligible change. The color changes were related with the cumulative solar energy at various water activities $(a_w)$. As decreasing $a_w$ below 0.5, the bleaching reaction was highly accelerated, and thereafter was slowly progressed. Sun lights transmitted by red-, yellow- and blue-gelatin filters, respectivly, bleached in different degrees and at the shorter wavelength light, the more color bleaching occurred. From this fact a red colored package film could be effectivly used for the color preservation purpose in the red pepper storage.