• Journal of the Korea Furniture Society
• /
• v.19 no.2
• /
• pp.116-123
• /
• 2008

Kiln schedule development was based on two schedule phases, the first being to determine the maximum safe kiln temperature during the check prone initial stage of drying, with the second stage determining how to accelerate drying once the danger of checking had passed. This was achieved by using 38 mm thick boards which were pre-screened for susceptibility to internal checking, and then drying matched sample boards over a range of kiln temperatures. Research has shown that below 50% MC there is no further risk of internal checking. However, difference in drying rate due to board width and the increased occurrence of wet patches in wide boards means that it is essential to modify the basic schedule according to the maximum board width. A condition of 52/40 $^{\circ}C$ was selected for the checking-free initial kiln drying step and a 5-step kiln-schedule dried the boards from 109% to 8% MC for 72.5 hours without internal checking.

• Journal of the Korea Furniture Society
• /
• v.10 no.2
• /
• pp.29-36
• /
• 1999

During a radio-frequency/vacuum plus press drying process of some hardwood veneers for decoration we investigated the effect of a grain and thickness of a veneer sheet on drying rates, variations of final moisture content within a bundle of veneer sheets, and formation of checking, end waving, and burning mark. About thirty three hundreds sheet of veneer could be dried in sixty five hours from green to in0-use moisture content, and a final moisture content was significantly effected by initial moisture content of veneer. There were nearly variations in a final moisture content among the veneer sheets in the same bundle. A checking was never found in a edge-sliced veneer, and very slight in a flat-sliced veneer of ash and red oak. There were no end waving and no burning mark in all veneer sheets.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.33-46
• /
• 2006

This study was carried out to investigate a radio-frequency/vacuum (RF/V) drying ability and physical properties of the green boards and the pre-kiln dried boards with 40 mm thickness, and the 70 mm-thick green board of Iroko (Milicia excelsa). The major results were summarized as follows; The drying time from initial moisture content (MC) of 110% to approximate 6% MC for a 40mm-thick green board was 192 hours, and about 200 hours for the 70 mm-thick green board, respectively and so the RF/V drying times were dramatically shortened compared to conventional kiln drying time. The case hardenings at the RF/V drying completion stage test were very negligible, thus represented almost no existence of the residual stress. The checks were very slightly formed on all of the boards during the RF/V drying test, but crook appeared quite severely. During the accelerating test, the water-resistant treated specimens had not experienced any signs of checking occurred, whereas the control boards had encountered very frequent occurrences of end checking and slight surface checking. There were no observations of warping and discoloring regardless of the treatment.

• Journal of the Korea Furniture Society
• /
• v.11 no.1
• /
• pp.61-68
• /
• 2000

This study was carried out to investigate the effect of grain and veneer thickness on drying rate, required energy consumption, and drying defects such as checking, end waving, and burning during a far-infrared radiation drying process of decorative veneers of hard maple and beech. Most of the veneer could be dried from green to in-use moisture content within 30 to 360 seconds. The drying rates were significantly affected by veneer thickness, but there was little difference between edge-and flat-sliced veneers. The formation of checking during drying test was none or very slight. The percentages of the veneers defected by checks were higher in the flat-sliced veneers than in the edge-sliced veneers. The maximum end wavinesses in the flat-sliced veneers were almost 1.6 to 3 times larger than that in the edge-sliced veneers. All veneers were fee from burned marks during drying test.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.4
• /
• pp.29-39
• /
• 1986

To investigate the effect of presurfacing, both 25mm rough and pre surfaced oak boards (Quercus grosseserrata BI.) were dried in the same dry kiln condition. Drying curves, drying strains and drying defects of rough and presurfaced boards were compared. The results obatained are as follows. 1. Average drying rate of rough and presurfaced boards from green to 10% M.C. was 0.276%/hr. and 0.284%/hr., respectively. 2. At the early stage of drying, in case of rough boards, maximum tensile strain of outer slices was $-24.2{\times}10^{-4}$mm/mm and maximum compressive strain of innermost slices was $13.0{\times}10^{-4}$mm/mm, and in case of pre surfaced boards, maximum tensile strain of outer slices was $-14.5{\times}10^{-4}$mm/mm and maximum compressive strain of innermost slices was $28.1{\times}10^{-4}$mm/mm. And in both cases, stress reversal occurred at about 40% M.C.. 3. Maximum surface checking appeared at about 40% M.C.. Of the 10 rough boards. 6 hoards contained surface checks, but presurfaced boards did not contained surface checks after drying. And the results of end checking were similar to those of surface checking. But, honeycomb was not found in both cases. 4. Board shrinkage. warp and casehardening of presurfaced boards were similar to those of rough boards. But, collapse of prsurfaced boards was less than that of rough boards.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.67-78
• /
• 1987

This study was designed to investigate the effect of board thickness and ring angle on the characteristics including internal check. ring failure, surface check, end check, collapse, thickness shrinkage and width shrinkage of press-drying. The exprimental materials of 6mm-. 9mm- and 12mm-thick board were taken from heartwood and sapwood of oak (Quercus acutissima Carr.) respectively. And boards were numbered according to position in the log(No. 1 to No. 4 for heartwood :md No. 9 for sapwood). Press-drying was at $145^{\circ}C$ platen temperature and 3.5kg/$Cm^2$ platen pressure. The results of this study were summarized as follows. 1. Drying rates for sapwood materials were greater than those for heartwood materials. And drying rates for thinner materials were greater than those for thicker materials. 2. The thinner boards were. the severer surface checking developed in the heartwood materials, and surface checking for heartwood materials had no tendency in board position for the same thickness. Sapwood materials were completely free from surface checking. 3. End checking for heartwood materials had no tendency in board position. The greater deviation of ring angle from perfectly edge-grained was, the severer and checking developed in the sapwood materials. But end checking did not occur in 6mm-thick sapwood materials. 4. The greater deviation of ring angle from perfectly edge-grained was, the severer end checking developed for heartwood and sapwood materials. As board thickness increased, maternal checking developed more severely for heartwood and sapweed materials. 5. For heartwood materials, ring failure, reduced with increasing deviation of ring angle from perfectly edge-grained except 12mm-thick material and showed no significant difference attributable to board thickness. Sapwood materials were completely free from ring failure. 6. For heartwood and sapwood materials, collapse was slight and showed no significant differences attributable to both board thickness and board position. 7. As deviation of ring angle from perfectly edge-grained increased, shrinkage of board thickness decreased for heartwood and sapwood materials. 8. Shrinkage of board width showed no significant differences attributable to both board thickness and board position for heartwood and sapweed materials.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.1
• /
• pp.45-54
• /
• 1986

A study was conducted to determine the physical properties related to drying characteristics, the seasonal air drying curves and the kiln drying schedule for taun lumber imported and utilized. This kiln drying schedule was found by oven drying and developed by pilot testing of green lumber and partially air dried lumber. The results of this study were as follows; 1. Average green specific gravity and standard deviation of heartwood lumber were 0.60${\pm}$0.03 and those of sapwood lumber were 0.64${\pm}$0.02. 2. Radial shrinkage from green to air dry and from green to oven dry were 3.05 percent and 5.96 percent respectively, and tangential shrinkage from green to air dry and to oven dry were 5.49 percent and 8.74 percent respectively. 3. Drying time for 25mm thick green lumber (50 percent moisture content) air dried to 30 percent moisture content were 14 days in springtime. 6 days in summertime, and 12 days in autumntime, whereas for 50mm thick lumber in 36 days in springtime, 18 days in summertime, 38 days in autumntime. 4. Kiln drying schedules developed by oven drying were T8-B3 for 25mm thick lumber and T5-B2 for 50mm thick lumber. 5. Kiln drying curves of green 25mm and 50mm thick lumber were similar to those of partially air dried lumber from the level of 30 percent average moisture content. Green 25mm thick lumber (55.7 percent moisture content) was dried to 9.3 percent moisture content in 101.5 hours and green 50mm thick lumber (65.6 percent moisture content) was dried to 11.5 percent moisture content in 526 hours. 6. End checking for green 25mm thick lumber occured in 49.6 percent moisture content and reached maximum amount in 27.6 percent moisture content and closed in 15.8 percent moisture content. 7. End checking for green 50mm thick lumber and partially air dried lumber developed and reached maximum amount earlier then for 25mm thick lumber. 8. Final moisture content of surface layer for 50mm thick lumber was one half of that of core, and moisture content equalized in the lumber after nine days of room conditioning. 9. Casehardening for 50mm thick lumber was slight and was conditioned after nine days of room stroage. 10. Drying defects, such as end checking and surface checking, were not observed and the quality of dry lumber was first.

• Journal of the Korean Wood Science and Technology
• /
• v.4 no.1
• /
• pp.48-53
• /
• 1976

This Study was carried out to investigate the course of air-drying and drying defects of red pine (Pinus densiflora S. et Z.) and Italian poplar (Populus eurameriana I-476) boards 1,2 and 3cm thick in the flat pile. The results are as follows. 1. Air-drying curves for red pine and Italian poplar boards were same as figure 1 and 2. These moisture contents were lower in July and August during seasoning periods. 2. Air drying time of red pine board required to dry 15 percent moisture content in one week for 1 cm board, five weeks for 2 cm board and six weeks for 3cm board respectively. In case of Italian poplar boards, in one week for 1 cm board, four weeks for 2 cm and five weeks for 3 cm board. The thickness of board influenced the time for air drying. 3. Drying defects such as checking, warping and staining happened badly in pine than in Italian poplar boards. Especially, checking was severe in thicker board and warping in thinner board.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.3
• /
• pp.28-32
• /
• 1995

The presteamed or prefrozen persimmon blocks of 10cm ${\times}$ 10cm ${\times}$ 15cm were air-dried at room temperature until about 30% moisture content, and then were dried in a MW oven. During drying their internal temperatures were monitored with thermo-couple probes. The presteamed and prefrozen blocks didn't show any improvement in drying rate and moisture gradient when compared with the controls. Checks appeared on the surfaces of most presteamed blocks during air-drying. It has been clearly revealed that the maximum weight, loss must, be less than 2g/min during MW drying to prevent internal checking and that MW drying reduced moisture gradients inside blocks. MW dried the persimmon blocks 440 times faster than conventional kiln.

• Journal of the Korea Furniture Society
• /
• v.14 no.2
• /
• pp.13-20
• /
• 2003

This research is to develop kiln-drying schedules for 2.7 mm thick boards of Neolitsea sericea and Dendropanax morbifera, which grow in the southern region of Korean Peninsula. These two species are lesser-known to woodcraft industry in this country. The proper USDA drying schedules for Neolitsea sericea and Dendropanax morbifera were found to be T10-C6 and T10-E6, respectively, by using the Quick Oven-drying Method. The boards dried in a kiln with the newly-developed schedules were revealed to be free from warping and checking.