• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.306-312
• /
• 1998

This paper describes syntheses of thickener for di-urea grease using constant velocity joint. The thickeners of di-urea grease were synthesized by reaction of diisocyanate with various alkylamines, hexylamine, octylamine, stearylamine and cyclohexylamine at high temperatxire. The synthesized thickener were analyzed by FT-IR spectroscopy and two kinds of Mass spectroscopy (EI & FAB). Dropping point and Consistency of synthesized di-urea grease were determined.

• Journal of Environmental Impact Assessment
• /
• v.22 no.6
• /
• pp.569-579
• /
• 2013

To identify the characteristics of the dropping habits and to provide improved methods for sign survey of Siberian flying squirrels Pteromys volans, an investigation was carried out in Jirisan National Park from April 2012 to May 2013. The latrines of study area were checked once a month and the characteristics of dropping behavior were camera trapped. The feces of Siberian flying squirrel were found on the point which tree forked, mostly from November to May. The squirrel actively presents in forked tree mainly on the September to April. The Siberian flying squirrel is found to be a typical nocturnal animal as it actively move between 6p.m. to 7a.m.. The study found that squirrel does feeding and dropping in the winter time on forked tree. On the point which tree forked could be a good place for the squirrel to hide from their predator when there is no leaf on the tree. Conducting the sign survey is advisable from November to May, as well as with the careful approach to the animals. As Siberian flying squirrel is an endangered species, adjusting the survey period is mandatory, especially when doing environmental impact assessment and a research on its dwelling areas.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.269-275
• /
• 2006

Rolling bearings are classified one of the most important machine elements. The various function of bearings are greatly influenced by grease, and higher performance of rolling bearing greases is required to improve bearing lubrication. Three urea/ether oil greases with different composition were synthesized to compare the performance of these greases. The typical grease physical properties were investigated, and life test of these greases was conducted by FE-9 grease life tester. The grease with higher content of the thickener showed higher performance. After these preliminary test, twelve greases were synthesized and evaluated the performance of dropping point and OIT value. And optimized conditions for grease synthesis were selected by SSRED (Six Sigma Robust Engineering Design) using dropping point and OIT value respectively. The optimized grease using OIT value showed longer grease life than that using dropping point. Two greases were synthesized following the optimum synthesis conditions by means of OIT value. Then grease life and other properties of these greases were investigated. These two greasaes showed longer grease life than typical urea/ether oil grease.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.129-138
• /
• 2003

Rolling bearings are classified one of the most important machine elements. The various function of bearings are greatly influenced by grease, and higher performance of rolling bearing greases is required in improve bearing lubrication. Three urea/ether oil greases with identical composition were synthesized to compare the performance of these greases according to the thickener content of grease. The typical grease physical properties were investigated. And life test of these greases was conducted by FE-9 grease life tester. The characteristics of the greases before and after life test were investigated using FT-IR, microscope, OIT and TAN meter. Large differences in the grease performance depending on the content of the thickener were observed. The grease with higher content of the hickener showed higher performance such as long life time and low TAN value. After preliminary test, twelve greases were synthesized and evaluated the performance of dropping point and OIT, then optimized two greases were selected by SSRED (Six Sigma Robust Engineering Design) using dropping point and OIT data. Characteristics of the optimized two greases were on the same level with estimated value. The optimized grease by means of OIT value showed longer grease life in comparison with optimized grease by dropping point. However two greases showed higher performance than typical urea/ether oil.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.338-340
• /
• 2014

The purpose of this research is to support decision making of emergency rescue system with GIS which selects landing point of emergency rescue for emergency situation on mountains and dropping point when landing is impossible. The area of research was limited to Pocheon-si, Gyeonggi-do. The results were divided into two values; landing point of helicopter on mountains and dropping point. Digital map, forest type map and forest soil map were utilized as fundamental data. Factors of landing point were slope, topographical characteristics, vegetation characteristics and area of helicopter landing point by helicopter data. And, for dropping point, slope and vegetation characteristics were divided as factors and GIS intersect function was utilized for the analysis. But, this research was conducted by excluding factor values of wind direction, wind velocity, etc. In the future, it's necessary to improve effectiveness of the analysis more by making a connection with Meteorological Agency DB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2A
• /
• pp.187-194
• /
• 2004

We propose priority-based reservation code multiple access (P-RCMA) which can enhance voice traffic quality of the previous RCMA. The proposed protocol maintains two power levels and consider traffic characteristics in contending shared available codes to transmit packets. P-RCMA gives priority to the voice request packets rather than data packets by capture effect at the receiver part of base station. We show numerical results from EPA (equilibrium point analysis) analysis and simulation study in terms of voice packet dropping probability and average data packet transmission delay.

• Explosives and Blasting
• /
• v.33 no.2
• /
• pp.25-39
• /
• 2015

The common underwater rock removal methods involve underwater blasting and crane's chisel dropping impact method. From an environmental point of view, these methods cause ground vibrations and underwater noise. At the site for this study, a method of dropping heavyweight chisel is selected to remove the underwater bedrock near the ferry rack in the course of improving the cargo handling ability of the loading dock. A prediction formula for the vibration was obtained based on the measurement and evaluation of the vibrations caused by the chisel dropping impacts during the test droppings. The prediction formula was successfully applied to the main construction for securing the stability of the structure.

• Journal of Environmental Health Sciences
• /
• v.38 no.2
• /
• pp.118-127
• /
• 2012

Objectives: This study was undertaken to assess the sanitary conditions in the kitchens of food court/cafeterias and determine seasonal variations. Methods: We measured environmental factors (air temperature, relative humidity, illumination intensity, noise level), and dropping airborne microbes (bacteria and fungi) in the kitchens of eight food court/cafeterias in four seasons (January, April, July, and October). Air temperature and relative humidity were measured with in/out thermo-hygrometers at 1.2-1.5 m above floor level. Illuminance measurement was performed through the multiple point method of Korean Standards (KS). Noise level was measured by the standard methods for the examination of environmental pollution (noise and vibration) of Korea. The estimation of dropping airborne bacteria and fungi was performed through use of Koch's method. Results: The highest kitchen air temperature was in July, and the lowest in January. The average temperature surpassed $21^{\circ}C$ throughout the seasons, suggesting a higher temperature than required for the safe handling of food. Humidity in all the kitchens was measured in the range of 50-60%. Half of the kitchens showed illumination intensities below 300 Lux in April. It was found that the sound pressure level of noise in almost all of the kitchens was higher than 85 dB (A). The highest levels of dropping airborne bacteria and fungi were noted in July. The numbers of airborne bacteria were higher than those of fungi. The levels of dropping airborne bacteria and fungi were affected by air temperature, relative humidity, season, and place. Conclusions: This study indicates that the kitchen environments were unqualified to supply safe food. The hygiene level of the kitchens should be improved.

• Journal of Korean Institute of Industrial Engineers
• /
• v.19 no.4
• /
• pp.3-11
• /
• 1993

We propose a new dual simplex method using a primal interior point. The dropping variable is chosen by utilizing the primal feasible interior point. For a given dual feasible basis, its corresponding primal infeasible basic vector and the interior point are used for obtaining a decreasing primal feasible point The computation time of moving on interior point in our method takes much less than that od Karmarker-type interior methods. Since any polynomial time interior methods can be applied to our method we conjectured that a slight modification of our method can give a polynomial time complexity.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.6
• /
• pp.41-49
• /
• 2004

In general, open trenches or in-filled trenches have been used to isolate transmitting of vibration. Recently alternative methods, in which various materials are used for wall barriers have been proposed and performed in several sites. Although the effects of these methods are verified, resonable and qualitative evaluation methods have not yet been conducted. It may be because many factors, such as the characteristics of vibration sources, ground condition, and parameters of wall barrier are coupled complicatedly. In this study, a series of centrifugal modelings were conducted in order to examine the evaluation method of a vibration wall barrier when point load transmits to the surface. The experiments were performed with different stiffness of wall barriers and different depths of installations. Using the results obtained from tests, effects of those variables on the efficiency of vibration barrier were analyzed. Through this investigation we observed vibration transmission of under ground, and verified the applicability of ball dropping system which was developed in this study.