• 제어로봇시스템학회논문지
• /
• 제3권4호
• /
• pp.415-421
• /
• 1997

A car driving trainer for beginners developed under PC-based environment is described in this paper. For this trainer, a hardware is implemented as a practice car, and a trainer program is designed by computer image generation method to display 3-dimensional images on a CRT monitor. The trainer program consists of 3 main parts, that is, a speed estimate part, a wheel trace calculation part and a driving image generation part. Furthermore, a map editor is also installed for taking any test drive. After comparing this driving trainer to specify it was verified that the developed car driving trainer showed has good performances, such as lower cost, higher resolution and better image display speed.

• 한국군사과학기술학회지
• /
• 제15권6호
• /
• pp.721-728
• /
• 2012

The tracked SUGVs(Small Unmanned Ground Vehicles) are frequently operated in the narrow slope such as stairs and trails. But due to the nature of the tracked vehicle which is steered using friction between the track and the ground and the limited field of view of driving cameras mounted on the lower position, it is not easy for SUGVs to trace narrow slopes. To properly trace inclined narrows, it is very important for SUGVs to keep it's heading direction to the slope. As a matter of factor, no roll value control of a SUGV can makes it's heading being located in the direction of the slope in general terrains. But, the problem is that we cannot directly control roll motion for SUGV. Instead we can control yaw motion. In this paper, a new slope driving method that enables the vehicle trace the narrow slopes with IMU sensor usually mounted in the SUGV is suggested which including an estimation technique of the desired yaw angle corresponding to zero roll angle. In addition, a fuzzy steering controller robust to changes in driving speed and the stair geometry is designed to simulate narrow slope driving with the suggested method. It is shown that the suggested method is quite effective through the simulation.

• 융복합기술연구소 논문집
• /
• 제6권1호
• /
• pp.13-16
• /
• 2016

The purpose of this study is analysing the characteristics of vehicle fuel economy and greenhouse gase emissions according to driving pattern of drivers. Current fuel economy has not established on official test methods. The difference between actual fuel efficiency and specification fuel efficiency bring up consumer complaints and misunderstandings about fuel economy. Against this background, The country is progressing the study on influence of the fuel efficiency according to variety test conditions. This study analyze the driving pattern of the different drivers and influence of the fuel efficiency according to driving pattern of different drivers.

• 로봇학회논문지
• /
• 제18권1호
• /
• pp.93-98
• /
• 2023

In this paper, the development of an autonomous electric vehicle for logistics with a robotic arm is introduced. The manual driving electric vehicle was converted into an electric vehicle platform capable of autonomous driving. For autonomous driving, an encoder is installed on the driving wheels, and an electronic power steering system is applied for automatic steering. The electric vehicle is equipped with a lidar sensor, a depth camera, and an ultrasonic sensor to recognize the surrounding environment, create a map, and recognize the vehicle location. The odometry was calculated using the bicycle motion model, and the map was created using the SLAM algorithm. To estimate the location of the platform based on the generated map, AMCL algorithm using Lidar was applied. A user interface was developed to create and modify a waypoint in order to move a predetermined place according to the logistics process. An A-star-based global path was generated to move to the destination, and a DWA-based local path was generated to trace the global path. The autonomous electric vehicle developed in this paper was tested and its utility was verified in a warehouse.

• 대한원격탐사학회지
• /
• 제25권1호
• /
• pp.61-69
• /
• 2009

본 논문은 제주 택시 텔레매틱스 사업에서 수집된 차량의 운행 이력 데이터를 효과적으로 가시화 하기 위해 Google Earth를 이용하여 데이터를 표현하는 시스템의 설계와 구현기법에 대해 기술한다. 이 시스템은 전체 차량의 운행상황을 확인하거나 특정 차량의 궤적을 추출하거나 특정 영 역을 통과한 차량을 검색하는 등의 기능으로 다양한 택시 텔레매틱스 운행 이력 데이터의 분석이 가능하다.

• 한국산학기술학회논문지
• /
• 제14권1호
• /
• pp.57-62
• /
• 2013

카트 차체에는 현가장치와 차동장치가 존재하지 않으므로 카트주행 중 발생하는 프레임의 변형은 탄성변형으로 인한 주행성능과 프레임의 피로수명에 영향을 미친다. 선회주행 시 비틀림 변형에 의한 카트의 거동은 이 두 가지 변형에 결정적 원인을 제공한다. 이러한 곡선구간에서 카트의 동적 거동을 분석하기 위하여 GPS를 이용하여 차량의 궤적을 추적하고 카트 프레임 강에 작용하는 비틀림 응력을 측정하였다. 레저와 레이싱 카트 프레임의 기계적 성질을 파악하기 위해 재질 분석과 인장시험을 실시하여 각 프레임의 재료 특성을 분석하였다. 비틀림 응력집중과 프레임 비틀림은 프레임 해석을 통해 조사되었다. 또한 주행 분석 장치를 이용하여 레저와 레이싱 카트를 각 조건별로 실차실험을 수행하였고, 이를 통해 곡선구간에서 카트의 주행거동을 분석하였다. 선회주행 시 차량에 원심력에 의한 하중이동의 현상이 발생했으며, 이로 인해 카트 프레임 강에 비틀림 응력이 발생하였다.

• 제어로봇시스템학회논문지
• /
• 제15권7호
• /
• pp.734-741
• /
• 2009

A new localization algorithm is proposed for a fast moving mobile robot, which utilizes only one beacon and the global features of the differential-driving mobile robot. It takes a relatively long time to localize a mobile robot with active beacon sensors since the distance to the beacon is measured by the traveling time of the ultrasonic signal. When the mobile robot is moving slowly the measurement time does not yield a high error. At a higher mobile robot speed, however, the localization error becomes too large to locate the mobile robot. Therefore, in high-speed mobile robot operations, instead of using two or more active beacons for localization, only one active beacon and the global features of the mobile robot are used to localize the mobile robot in this research. The two global features are the radius and center of the rotational motion for the differential-driving mobile robot which generally describe motion of the mobile robot and are used for the trace prediction of the mobile robot. In high speed operations the localizer finds an intersection point of this predicted trace and a circle which is centered at the beacon and has the radius of the distance between the mobile robot and the beacon. This new approach resolves the large localization error caused by the high speed of the mobile robot. The performance of the new localization algorithm has been verified through the experiments with a high-speed mobile robot.

• 경영과학
• /
• 제22권1호
• /
• pp.15-26
• /
• 2005

The bootstrap is a method of computational inference that simulates the creation of new data by resampling from a single data set. We propose a new job for the bootstrap: generating inputs from one historical trace using Threshold Bootstrap. In this regard, the most important quality of bootstrap samples is that they be functionally indistinguishable from independent samples of the same stochastic process. We describe a quantitative measure of difference between two time series, and demonstrate the sensitivity of this measure for discriminating between two data generating processes. Utilizing this distance measure for the task of generating inputs, we show a way of tuning the bootstrap using a single observed trace. This application of the threshold bootstrap will be a powerful tool for Monte Carlo simulation. Monte Carlo simulation analysis relies on built-in input generators. These generators make unrealistic assumptions about independence and marginal distributions. The alternative source of inputs, historical trace data, though realistic by definition, provides only a single input stream for simulation. One benefit of our method would be expanding the number of inputs achieving reality by driving system models with actual historical input series. Another benefit might be the automatic generation of lifelike scenarios for the field of finance.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 춘계학술대회
• /
• pp.627-630
• /
• 2009

해상용 Multi Sensor Surveillance System은 다양한 기술의 복합체로서 본 과제에서 개발하고자하는 Gyro Sensor based Servo Motion Control 알고리즘은 선박의 6자유도운동을 분석하여 그에 대응할 수 있는 Motion Control 동요안정화제어장치를 개발하는 것이며, Nano Driving Precision Pan-Tilt/Gimbal System은 초정밀 초고속으로 감시용 디바이스를 적시에 정확한 동작을 수행하게 해주는 필수적인 장비이다. 최종적으로 개발하고자 하는 분야는 해상용 Nano Driving Multi Sensor Surveillance System 중 Nano Driving Precision Pan-Tilt/Gimbal의 최적설계 및 제작, 3-axis Gyro Sensor based Servo Motion Control 알고리즘 개발, 영상추적 Video Tracking Software 및 Hardware의 개발 및 각 세부주관에서 개발한 각각의 장비를 하나의 시스템으로 통합하는 시스템 Integration 및 시험인증으로 하나의 시스템을 완성 하였다.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권5호
• /
• pp.506-511
• /
• 1996

This paper deals with an inexpensive, simple and fast Langmuir probe sweeping circuit and its application. This sweeper completes a probe trace in a 1 ms order. Futhermore, the circuit drives a maximum probe voltage of $\pm$30V and has a maximum probe current capability of a few amperes. The plasma parameters are successfully determined using the fast Langmuir probe method.