• 한국지반공학회논문집
• /
• 제38권11호
• /
• pp.97-106
• /
• 2022

국내 매입말뚝 시공방법은 선굴착 후 최종단계의 항타 관입량으로 관리하는 것이 일반적이다. 관입량은 오래전부터 수기 측정방식에 의해 이루어지고 있으며, 작업자의 안전문제와 측정값의 신뢰도 부족 등에도 작업성의 한계와 비용 문제로 자동화 기술이 적용되지 않고 있다. 본 연구에서는 비접촉식 말뚝 관입량 측정 장치를 개발하고 기존 장치와 비교계측을 통해 현장 성능을 검증하였다. 또한 관입량 측정장치를 활용하여 현장 품질관리 방법에 대해 분석하였다. 실제 현장 실험을 통해 개발 장치를 활용한 관입량 측정과 수정 Hiley공식 및 동적감쇠계수 산정을 통해 보다 신뢰도 높은 지지력 추정이 가능한 것을 확인하였다. 연구결과에 따라 각 현장마다 수행된 동재하시험으로 부터 현장 보정 절차가 이루어지면 보다 신뢰성 높은 지지력 추정이 가능하며, 실제 현장에서는 동재하시험이 수행되지 않은 말뚝에 대해서도 지지력 관점의 말뚝 시공관리에 활용할 수 있을 것으로 판단된다.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.44-49
• /
• 2011

The crawler crane, which consists of a lattice boom, a driving system, and movable vehicle, is widely used in a construction site. It needs to be installed an overload limiter to prevent the overturning accident and the fracture of structure. This research is undertaken to provide the relation formula for designing the overload limiter as follows: First the relation formulas between the wire-rope tension and the hoisting load or the overturning ratio according to the luffing angle and length of a lattice boom are established. Secondly the derived formulas are corrected by using the compensated angle considering the deflection of boom through the finite element analysis. The stiffness analysis is carried out for 30-kinds of models as a combination of 6-kinds of luffing angle and 5-kinds of length of boom. Finally the shape design of a stick type load cell, which is the device to measure the wire-rope tension, is performed. 5-kinds of notch radius and 5-kinds of center hole radius are adopted as the design parameter for the strength analysis of the load cell.

• 한국자동차공학회논문집
• /
• 제5권1호
• /
• pp.110-119
• /
• 1997

Four wheel steering(4WS) systems which can control the lateral and yaw motions of vehicles by steering front and rear wheels simultaneously, have been regarded as effective for improving the stability and handing performance of vehicles. However, since the 4WS systems depend only on the lateral force of tire, they have some limitation due to the nonlinear characteristics of tire related with the saturation phenomenon of lateral force to the slip angle of tire in a near-limit-performance maneuvering range. In this study, in other to evaluate the effect of nonlinear characteristics of tire on the dynamic performance of vehicles, a new concept for driving the cornering stiffness of nonlinear tire by using the "Magic Formula" tire model is proposed. In addition, the nonlinear 4WS vehicle model is constructed based on the proposed cornering stiffness of nonlinear tire. It is noted from simulation that the nonlinear characteristics of tire affect greatly on the 4WS vehicle performance.rformance.

• 한국산학기술학회논문지
• /
• 제18권10호
• /
• pp.725-732
• /
• 2017

경량화는 현재 자동차 산업에 있어 가장 중요하게 여겨지는 화두 중 하나이다. 내연기관은 물론 미래형 자동차, 친환경 자동차 개발을 위해 경량화는 자동차 산업에 있어서 결코 빠질 수 없는 소재이다. 친환경 자동차를 개발하는데 있어 연비향상과 주행성능향상은 경량화가 핵심이기 때문이다. 본 연구팀에서도 포뮬러 형태의 자작자동차를 제작하면서 경량화와 최적설계를 통한 주행 성능 향상에 주안점을 두고 연구를 시작하였다. 본 연구는 전년도 제작 차량을 바탕으로 다음의 네 가지 항목으로 나누어 진행하였다. 첫 번째, 엔진의 교체를 통한 엔진룸의 구조설계 및 경량화. 두 번째, 프레임의 최적설계를 통한 부재의 단순화 및 경량화 연구. 세 번째, 프레임의 최적설계에 따른 서스펜션의 구조설계 및 해석. 마지막으로, 업라이트와 허브의 설계 및 경량 부품 사용을 통한 경량화 등이다. 이러한 목표설정을 두고 차량 설계를 진행하였으며 결과적으로 전년도 차량 대비 48 kg을 감량하여 19.5% 만큼의 경량화 하였고 이에 가속도 또한 80 m 기준 6.65 s에서 5.8 s만큼 단축시켰다.

• 한국자동차공학회논문집
• /
• 제18권4호
• /
• pp.92-98
• /
• 2010

Virtual ground modeling is one of key topic for real-time vehicle dynamic simulation. This paper discusses about the virtual 3D road modeling process using parametric surface concept. General road data is a type of lumped position vector so interpolation process is required to compute contact of internal surface. The parametric surface has continuity and linearity within boundaries and functions are very simple to find out contact point. In this paper, the parametric surface formula is adopted to road modeling to calculate road hight. Position indexing method is proposed to reduce memory size and resource possession, and a simple mathematical method for contact patch searching is also proposed. The developed road process program is tested in dynamic driving simulation on off-road. Conclusively, the new virtual road program shows high performance of road hight computation in vast field of off-road simulation.

• 대한조선학회논문집
• /
• 제42권2호
• /
• pp.136-141
• /
• 2005

An experiment method has been developed to analyse the vibration characteristics of marine propeller blades, and vibration tests have been carried out on the model scale propeller in air and in water. The driving point transfer function(acceleration/excitation force) has been measured and modified by compensating the attachment effect of the impedance head. The measured natural frequencies in air have been compared with the theoretical results by an in-house FEM code PROSTEC. The added masses have been derived by comparing the measured natural frequencies in air and in water, and the results have been compared to the results using existing formula based on experience.

• 동력기계공학회지
• /
• 제21권6호
• /
• pp.94-100
• /
• 2017

Due to the environmental problems caused by the greenhouse effect, regulation of $CO_2$ emissions is getting stronger day by day. In paricular, regulations of automobiles $CO_2$ emissions are being strengthen. However, existing $CO_2$ measurement methods do not reflect the environment and operating conditions on actual roads. Emissions of $CO_2$ can be increased by various conditions such as environmental condition(temperature and humidity) and driver's tendency(aggressive and passive). Therefore it is necessary to reflect the conditions of various actual roads such as 5-cycle test method on behalf of the existing $CO_2$ emission measurement method. The 5-cycle measurement method has five test modes; FTP-75, HWFET, US06, SC03, Cold FTP-75. The method reflects the following three environments and operating conditions as compared to conventional method; Using heater at low temperature, Aggressive driving such as rapid acceleration or deceleration, Using air conditioner at high temperature. Because of these various conditions of each test cycle, the 5-cycle method can reflect actual environments and operating conditions. This paper attempt to analyze $CO_2$ emission characteristics based on the results measured through the 5-cycle mode and develop the correction formula that can derive the results of the 5-cycle test method using existing test methods. As a result, the developed correction formula is expected to reduce $CO_2$ emissions and cut down expense for testing 5-cycle mode.

• 한국도로학회논문집
• /
• 제16권6호
• /
• pp.169-179
• /
• 2014

PURPOSES : This study is to conduct the research on the design principle for the driver's safety and comfort in installing consecutive curves of superhighway. METHODS : Superhighway does not currently exist in domestic area. Thus, this study is conducted by collecting driving behavior usage of 30 people who are involved in the members of the virtual driving simulation. By identifying the distribution characteristics of each scenario in ANOVA & Tukey Test, the distribution are categorized into three groups. RESULTS : In the case of Group A in Section 3 (R2 entry part), lane departure exceeds the safety standard, which means to be risky condition. And then in the case of Group B and C, the lane departure values applying theoretical formula was evenly distributed compared to the proven values. CONCLUSIONS : Based on the result, the continuous curve design principles at superhighway should follow three standards as follow. First, an additional linear part needs to be inserted between two curves. Second, what if inserting the linear part is difficult, it would be better to insert a curve more than 2,000m. Third, R1/R2 ratio should not be over two. This design primarily aims to the safety of the operator. Such road alignment also meets the expectations of drivers, thus, it may help drivers to be compatible and amenable while driving continuous curve in superhighway.

• 에너지공학
• /
• 제25권4호
• /
• pp.198-206
• /
• 2016

자동차 표시연비는 국가적으로 에너지관리 지표로서 활용되며, 자동차 제작사의 기술개발을 유도하고, 소비자 차량구매 시 정보제공의 역할을 담당하고 있다. 하지만 정부의 표시연비가 체감연비와 상이하다는 소비자 불만이 지속되어 정부는 보다 정확한 표시연비 측정을 위해 미국의 5-cycle 시험방법을 국내 차량 기준에 맞게 재설정하여 도입하였다. 본래는 다양한 환경조건 및 주행패턴이 반영된 5개의 시험모드를 모두 주행함으로써 측정된 결과 값을 표시연비로 계산하는 방법이지만 소요되는 자원의 급격한 증가에 따른 충격을 완화하기 위하여 2개의 시험모드(도심(FTP-75 mode), 고속도로(HWFET mode))의 결과 값을 5-cycle 시험법으로 계산된 연비 값과 동등한 수준으로 산출하는 5-cycle 보정식을 사용하고 있다. 이 보정식은 2011년에 30대 차량의 5-cycle 시험방법으로 산출되었으나 최근 자동차 기술의 급속한 발전으로 인한 신형식 자동차에 대한 기존 5-cycle 보정식에 대한 검토가 필요할 것으로 판단되었다. 본 연구에서는 최근 기술이 적용된 14대의 신형식 자동차를 대상으로 기존과 동일한 시험 방법을 통해 시험모드별 연비 특성을 확인하고, 기존에 개발된 보정식과 차이를 분석한 결과 기존 시험 차량 결과와 큰 차이를 보이지 않았으며 보정식 또한 최대 1.5% 이내의 오차로써 기존 연비 보정식은 현재의 자동차 기술발전에 따른 개선도에 크게 영향을 받고 있지 않음을 알 수 있었다.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.197-204
• /
• 2004

An accumulator in hydraulic systems stores kinetic energy during braking action, and then that controls hasty surge pressure. An energy recovery system using accumulator seems to be advantageous for ERBS due to its high energy density. This study suggests a method to decide suitable accumulator volume for ERBS. The method is based upon energy conservation between kinetic energy of moving inertia and elastic energy of accumulator. The energy conversion was analyzed and a simple formula was derived. Also accumulator tests were conducted for different load mass and motor speed. A series of test work were carried out in the laboratory and the dynamic characteristics of the hydraulic motor system, such as the surge pressure and response time, were investigated in both brake action and acceleration action and these results show that the proposed design is effective for decision accumulator volume in ERBS.