• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.769-773
• /
• 2004

Conventional SVPWM method has null switching vectors. Null switching vectors cause high common-mode voltage in induction motor drive system. The newly developed common mode voltage reduction PWM technique don't use zero switching state for inverter control. It is realized by changing software without additional hardware. Simulation and experimental results show that proposed method are reduced common mode voltage more than conventional method.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.660-664
• /
• 2004

The indirect rotor position detection method using terminal voltage of brushless DC motor (BLDCM) requires simple control circuit, and has wide speed range of sensorless operation. However, because the substantial phase difference exists between real back emf and terminal voltage, the existing indirect detection method using analog filter which is affected by frequency, speed, and load sensitively cannot be synchronized with current, in the end, it advances or delays. This paper presents new analog filter circuit design for rotor position estimation in order to solve the problem, and proposes novel sensorless operation method which is stable even in high speed range and not influenced by parameters with analysis on phase difference by load and speed. Moreover, the appropriateness of the proposed sensorless drive in this paper is verified and analyzed by experimentation.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.488-490
• /
• 1999

This paper describes the design of self-tuning speed controller for DC motor drive system using RLS(Recursive Least Squares) algorithm and Pole-Placement method. The model parameters, related to inertia and damping coefficient of motor, are estimated on-line by using RLS estimation algorithm. And a control signal is calculated by using pole placement method. Simulation and experimental results show that the proposed controller possesses excellent adaptation capability than a conventional PI/IP controller under parameter change.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2688-2690
• /
• 1999

This paper presents the modeling method of $3{\Phi}$ phase-controlled rectifier considering the overlap interval for the drive of DC motor in the Matlab environment. The model is constructed by the module-based method and therefore it is appropriate in the research of the closed-loop controlled power electronic system in the Matlab/Simulink environment. The model of SCR is used as the element for the power transformation. The simulation results show that the overlap interval from the effect of the input inductance is accurate.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1183-1192
• /
• 2000

This paper relates to the flexural vibration analysis of the hard disk drive (HDD) spindle systems by means of the finite element method. In contrast to previous researches, every system componebt is here analytically modeled taking into account its flexibility and also the centrifugal effect particularly for the disk. To prove the effectiveness and accuracy of the proposed method, commercial HDD spindle systems with two and three identical disks are chosen as examples. Then, their major flexural natural modes are computed employing only a small number of element meshes as the shaft rotaional speed is varied, and compared with the bumerical or experimental results.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.716-722
• /
• 2018

This paper presents a voltage angle control strategy for surface permanent magnet synchronous motor (SPMSM) drives used in low-cost applications, wherein a current vector control is not employed. In the proposed method, the current vector control scheme, which requires high precision phase-current sensing units and a fast calculation capability of a motor drive controller, is replaced with the voltage angle controller. The proposed voltage angle controller calculates a d-axis voltage command to make the d-axis current zero by using a simple equation obtained from the voltage equation of SPMSM. The proposed method shows performance similar to the current vector controlled SPMSM drive during steady-states and its structure is very simple and thus it can be easily implemented with a low-cost microcontroller. The effectiveness of the proposed method is verified through simulations and experiments.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.30-32
• /
• 1995

The SRM has high efficiency, a wide speed range, high speed capability and DC-series Motor characteristics. So the SRM has been studied as adjustable speed machine. The speed of SRM can be adjusted to switching angle and exciting voltage. This paper suggests an constant speed drive method of SRM. In this method, the speed is controlled by voltage regulation using PI control and the torque is controlled by advance angle in accordance with, load torque variation.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.4
• /
• pp.538-545
• /
• 2008

This paper attempts to summarize torque control strategy for high performance SR drive. There are primarily two strategies for torque control. One method is direct torque control, which uses the simple control scheme and hysteresis controller to reduce the torque ripple. Another method is indirect torque control, which uses the complicated algorithms or simple distribution function to distribute each phase torque and obtain current command. The current controller is used to control phase torque by a given current command. In order to compare these two strategies of torque control, five torque control methods are introduced. The advantages and disadvantages of each method are presented. At last, they are verified by some simulations and experimental results.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.147-152
• /
• 2000

The ASF(Automatic Sheets Feeders) part of the printer has many bosses supporting gear-trains. Steel-pin bosses are substituted for plastic mold bosses because of advantages such as cost reduction, convenience of manufacturing and accuracy in dimension, but they have a weak point such as fatigue fracture due to low material strength, which causes a serious problem in the reliability of product. To prevent the fatigue fracture of bosses, we should exactly estimate the life to failure of the various shapes of bosses. We take the linear FEM analysis and the statistical method in this paper to figure out the life to failure of bosses. The maximum stress and life to failure of bosses can be easily estimated by this method. This paper specifies how to figure out the life to failure of bosses.

• Transactions of Materials Processing
• /
• v.25 no.4
• /
• pp.248-253
• /
• 2016

Induction hardening process of tubular drive shaft for automobile is simulated by combining the thermal, mechanical, electro-magnetic and metallurgical analysis models. Various material properties for each analysis model are obtained in a consistent way via material properties calculation software, JMatPro^®. To consider the scanning process of induction heating, boundary element method is adopted for electro-magnetic field calculation. The distribution of temperature, stress and phase volume fraction are tracked out through the whole process and the effect of scanning velocity is reviewed. The analysis result shows that the critical principal stress is developed at the phase boundary where martensite is formed.