• Journal of The Korean Society of Agricultural Engineers
• /
• v.55 no.6
• /
• pp.155-165
• /
• 2013

Recently, geotextile tube method can be widely applied to the river, costal and marine in the construction field, such as embankment, groin, breakwater, dyke structures and so on, in advanced countries of the world. And that has been constructed at the temporary road for incheon, ilsan-bridge construction and coast erosion protection in republic of korea. Geotextile tube is a tube shaped geotextile product and hydraulic pumping filled with dredged soils. In this paper, the numerical analysis was performed to investigate the behavior of geotextile tube with various properties of material character, shape condition, construction pressure and so on. Also, the field test was conducted in order to identify the construction ability of Samangum waterproof embankment using geotextile tube. According to the applied of field test, geotextile tube was 65 m long and 4.0 m diameter. Also, the permeability coefficient and ultimate tensile strength of geotextile tube is $1.6{\times}10^{-1}$ cm/sec and 205.26 kN/m, respectively. As a result of filed test, when filled, geotextile tube does not attain the same as its unfilled theoretical diameter, but may reach approximately of 55 percent of the theoretical diameter. At the time, geotextile tubes were 12.56 m in circumference and filled to a height of about 2.2 m. This paper presents case study on field application and behavior analysis of the saemangum waterproof embankment donggin 1 division construction using geotextile tube.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.2
• /
• pp.77-83
• /
• 2014

The purpose of this study was to figure out the impacts of iron oxide types and dosages to bloating when producing artificial lightweight aggregates by utilization of recycled resources such as bottom-ash, reject-ash and dredgedsoil. In order to figure out chemical characteristics of raw materials, XRD and XRF analyses were performed. 50 wt% of dredged-soil, 15 wt% of bottom-ash and 35wt.% of reject-ash were mixed, then the amount of iron oxide was varied at 5 to 30 wt% with intervals of 5 wt% with $Fe_2O_3$ and $Fe_3O_4$ respectively. As molded aggregates were sintered by rapid sintering in intervals of $40^{\circ}C$ from $1060^{\circ}C$ to $1180^{\circ}C$, specific gravity and water absorption were measured. As a result, the artificial lightweight aggregate with iron oxide of 10~15 vol% showed the lowest specific gravity, and it was identified that the more iron oxide vol% increases, the more specific gravity increases because of liquid phase sintering.

• Geomechanics and Engineering
• /
• v.25 no.2
• /
• pp.143-157
• /
• 2021

Expansive soil is the most predominant geologic hazard which shows a large amount of shrinkage and swelling with changes in their moisture content. This study investigates the macro-mechanical and micro-structural behaviours of dredged natural expansive clay from coal mining treated with ordinary Portland cement or hydrated lime addition. The stabilised expansive soil aims for possible reuse as pavement materials. Mechanical testing determined geotechnical engineering properties, including free swelling potential, California bearing ratio, unconfined compressive strength, resilient modulus, and shear wave velocity. The microstructures of treated soils are observed by scanning electron microscopy, x-ray diffraction, and energy dispersive spectroscopy to understand the behaviour of the expansive clay blended with cement and lime. Test results confirmed that cement and lime are effective agents for improving the swelling behaviour and other engineering properties of natural expansive clay. In general, chemical treatments reduce the swelling and increase the strength and modulus of expansive clay, subjected to chemical content and curing time. Scanning electron microscopy analysis can observe the increase in formation of particle clusters with curing period, and x-ray diffraction patterns display hydration and pozzolanic products from chemical particles. The correlations of mechanical properties and microstructures for chemical stabilised expansive clay are recommended.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.5
• /
• pp.29-36
• /
• 2011

In this study, settling experiment was performed about cohesive and sandy soils among representative sample expected to dredge and dump for analysis of settling and consolidation characteristic. The analysis showed the definite difference between cohesive soils and sandy soils of relationships with settling and consolidation coefficient, a water content, interfacial heights. But directly after a dredged reclamation, prediction results about a initial volume change showed that cohesive soil of a water content change was decreased rapidly as time goes by, but sandy soils made no difference in a water content change. Results were compared and analyzed with the settling and consolidation coefficient and a initial settling velocity by real soil amounts for a feasibility check about test conditions applied to these experiment: we judge that test conditions are appropriate, each material by such these analyses suggests the scope of settling and consolidation coefficient, average and the representative relational formula.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.9
• /
• pp.33-40
• /
• 2008

This paper describes the performance of ground improvement project using prefabricated vertical drains of condition, in which approximately 10m dredged fill overlies original soft foundation layer in the coastal area composed of soft marine clay with high water content and high compressibility. From field monitoring results, excessive ground settlement compared with predicted settlement in design stage developed during the following one year. In order to predict the final consolidation behavior, recalculation of consolidation settlements and back analysis using observed settlements were conducted. Field monitoring results of surface settlements were evaluated, and then corrected because large shear deformation occurred by construction events in the early stages of consolidation. To predict the consolidation behavior, material functions and in-situ conditions from laboratory consolidation test were re-analyzed. Using these results, height of additional embankment is estimated to satisfy residual settlement limit and maintain an adequate ground elevation. The recalculated time-settlement curve has been compared with field monitoring results after additional surcharge was applied. It might be used for verification of recalculated results.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.5
• /
• pp.27-33
• /
• 2017

In this research, laboratory tests were carried out to investigate the engineering properties of Light-Weight Air Foamed Soil (LWAS) based on silty clays with the animal foaming agent and cement. LWAS has been used as an embankment material over soft ground for road and side extension of the existing road. In field, unit weight and flow value is measured right after producing in mixing plant in order to control the quality of LWAS, and laboratory tests are carried out to confirm the quality through compressive strength of LWAS as well. In this research, direct estimation of the specification requirement of strength using flow values in field is the main purpose of the study together with other characteristics. From the test results, it can be seen that flow values increase with the initial water content and unit weight increases with the depth due to material segregation. Compared to the upper specimen, lower end of 60 cm specimen shows about 2 times higher compressive strength. Relationship between flow values and normalized factor presented by Yoon & Kim (2004) was presented. With that relationship, compressive strength can be predicted from flow values in field. From the relationship, the normalized factor was calculated. Thereafter calculated compressive strengths according to the flow values were compared to measured strengths in the laboratory. The higher the initial water content of the dredged soil has, the better relationship between predicted and measured shows. Therefore it is necessary to predict the compressive strength in advance through the relationship between the flow value and the normalized factor to reflect it in the design stage.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2015.11a
• /
• pp.162-165
• /
• 2015

본 연구는 ${\bigcirc}{\bigcirc}$ 공구 공유수면 매립공사 수행 중에 매립토량의 부족이 발생함에 따라 이를 대상으로 원인을 분석하고자 수행하였다. 매립지의 토량부족 원인을 파악하기 위해 설계 및 계측자료를 수집하여 시공 현황을 파악하고 지반조사를 통해 해안지역과 매립지반의 시료를 채취하여 성상분석과 원지반에 대한 공학적 특성을 비교 검토하였다. 특히. 현장 시추조사에 의한 경계면 분석과 토질 종류를 점성토, 사질토, 부유토로 구분하고 침하량 공식에 따라 발생량을 산출하였다. 구역의 구분은 설계 시와 동일한 조건에서 침하량을 계산하였고 설계 시 지반고가 침식과 퇴적으로 인해 일부 변경되어 설계시 지반고와 착공시 지반고를 구분하여 기재하고 각각의 침하량을 비교하였다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.95-107
• /
• 2000

The primary purpose of dredging work is to maintain navigational readiness and to increase environmental amenity, so that the dredging project which is composed of excavating, removing, transporting, storing and disposing dredged material must be carefully managed to insure that dredging works are completed in a cost-effective and environmentally safe manner. The most important point in dumping operations is an estimating and reducing the impacts of discharges at the dumping area. One of the most effective method for the reduction of ecological impacts at dumping area is using the schematic process composed of the sophisticated plan, precise work and predicting/reducing the impacts based on the numerical model and field observation. In this study, the numerical model is used to predict the near-field spatial fate and begavior of effluent discharged from Confined Dumping Facility(CDF) located near coastal area. To to this purpose, reappearing of tidal current was preceded. The model is then applied to Mokpo harbor, where capital dredging and maintenance dredging are conducted simultaneously and the CDF is under construction;. In the series of model case study, we found that the near-field behavior of effluent discharged from CDF was governed by the receiving water condition, outfall geometry, characteristics of efflent and CDF operating conditions.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1992.10a
• /
• pp.55-60
• /
• 1992

Hydraulically filled ground is formed by the settling of soil grains from the mixture of soil grains and water. It was generally known that the settling speed of the soil grains in governed by Stokes low. In the case of clayed dredged material, the shape of soil grains is not round, the surface of the soil grains is relatively large compared to the weight of soil grains and inter-grain ionic force is relatively large compared to the wight of soil grains. By this reason the settling and consolidation behavior of hydraulically filled quite different from that of Stokes law. This study investigated the settling and consolidation behavior of hydraulically filled materials of Yeochon industrial complex by large scale laboratory settling & consolidation container. The test results showed tat actual settling speed of soil grains in quite large compared to that of Stokes law. It was turned out that this phenomenon was due to the aggregation of soil grains. Also, it was truned out that the void ration and water content after the completion of settling process was 8.7 and 322% respectively. The consolidtion settlement of clayey hydraulic fill material was predicated better by "incremental small strain" consolidation concept than classical Terzaghj's consolidation concept (infinitesimal strain).

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.300-306
• /
• 2014

To recycle coal bottom ash(denoted here as CBA) generated from thermal power plants as a functional construction material, artificial soil(denoted as AS) containing CBA with dredged soil(denoted as DS) at a ratio(wt%) of 70 : 30 was manufactured by means of material engineering with sintering in a rotary kiln at $1125^{\circ}C$ using a green body formed via extrusion processing. The properties of the soil mechanics of the AS and the as-received CBA were analyzed and compared. Compaction testing results determined an optimum moisture content of the AS and CBA at 18%. During these tests, the maximum dry unit weights of the materials were similar, at 1.57 and 1.58 $t/m^3$, respectively. The compressive strength levels of the AS and CBA concrete specimens were 5.1 and 5.4 $t/m^3$, respectively, both of which increased after materials engineering processing. In a consolidation test, the compression index of the AS and CBA was found to be $0.114{\pm}0.001$ in both cases. The values were similar regardless of the materials engineering processes, but during the consolidation of AS, its coefficient was higher than that of the CBA materials.