• International Journal of Aeronautical and Space Sciences
• /
• 제16권2호
• /
• pp.311-324
• /
• 2015

This study presents computational analyses for low-drag aerodynamic design that are applied to modify a long-endurance UAV. EAV-2 is a test-bed for a hybrid electric power system (fuel cell and solar cell) that was developed by the Korean Aerospace Research Institute (KARI) for use in future long-endurance UAVs. The computational investigation focuses on designing a wing with a reduced drag since this is the main contributor of the aerodynamic drag. The airfoil and wing aspect ratio of the least drag are defined, the fuselage configuration is modified, and raked wingtips are implemented to further reduce the profile and induced drag of EAV-2. The results indicate that the total drag was reduced by 54% relative to EAV-1, which was a small-sized version that was previously developed. In addition, static stabilities can be achieved in the longitudinal and lateral-directional by this low-drag configuration. A long-endurance flight test of 22 hours proves that the low-drag design for EAV-2 is effective and that the average power consumption is lower than the objective cruise powerof 200 Watts.

• 한국입자에어로졸학회지
• /
• 제9권4호
• /
• pp.271-277
• /
• 2013

This article reports the drag reduction phenomenon of aqueous suspensions containing carbon nanotubes (CNTs) flowing through horizontal tubes. Stable nanofluids were prepared by using a surfactant. It is found that the drag forces of CNT nanofluids were reduced at specific flow conditions compared to the base fluid. It is found that the friction factor of CNT nanofluids was reduced up to approximately 30 % by using CNT nanofluids. Increased kinematic viscosities of CNT nanofluids are suggested to the key factors that cause the drag reduction phenomenon. In addition, transition from laminar to turbulent flow is observed to be delayed when CNT nanofluids flow in a horizontal tube, meaning that drag reduction occurs at higher flow rates, that is, at higher Reynolds numbers.

• 항공우주기술
• /
• 제12권2호
• /
• pp.221-229
• /
• 2013

인간동력항공기의 개념을 분석하여 최고 성능의 인간동력항공기 개발을 위하여 필요시되는 동력증강 및 항력감소 설계에 대하여 연구하였다. 2012년 인간동력항공기 시범경진대회에 출전하기 위하여 유선형 동체 채택에 의한 항력저감 및 팔과 다리 힘 동시사용에 의한 동력증강개념을 제시하였으며 개념 확인을 위하여 동체의 전산해석 및 동력장치 설계를 수행하였다. 유선형 동체의 효과를 최대한 이용하기 위해서는 동체형상 설계가 중요하며 팔의 동력을 이용하기 위해서는 조종 장치의 설계가 중요하고 비행실험이 요구된다.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1712-1718
• /
• 2014

Experimental analysis according to the plasma actuator design variables was performed in order to verify the effects of sliding discharge plasma on aerodynamic drag reduction of a high-speed train. For the study, sliding discharge plasma actuator and high-frequency, high-voltage power supply were developed and experimented to figure out the best design variables for highest ionic wind velocity which could reduce the drag force. And then, 5% reduced-scale model of a high-speed train was built for wind tunnel test to verify it. From the results, it was confirmed that sliding discharge plasma had contribution to reduce the drag force and it had the potential to be applied to real-scale trains.

• 한국자동차공학회논문집
• /
• 제24권2호
• /
• pp.198-204
• /
• 2016

In this study, a wind tunnel test was conducted to measure the aerodynamic characteristics of a streamline-designed high-speed bus with the change of wind direction and speed and the result is compared with the aerodynamic performance of a commercialized high-speed bus model (Model-0) manufactured by Zyle Daewoo Bus Corp. Aerodynamic performance of the existing rear-spoiler was tested to prove its aerodynamic effect on the test model bus. From the study, it was found that 24.6 % of the total drag of the original bus model (Model-0) was reduced on the streamline-designed model bus(model-1) without the rear-spoiler but only 14.3 % of the total drag was reduced with the spoiler on the streamlined model bus. It means that the rear spoiler does not work properly with the streamlined model bus (model-1) and should be noted that an optimum design of a rear-spoiler of a vehicle is important to reduce the induced pressure drag and increase the driving stability of a vehicle against yaw motion. The experimental outcome was also compared to the previous numerical research result to evaluate the reliability of the numerical algorithm of the aerodynamic performance analysis of a vehicle. The error rate (%) of the numerical result to the experimental output is about 5.4 % and it is due to the simplified body configuration of the numerical model bus. The drag increases at the higher yaw angle because the transparent frontal area of the model vehicle increases and the downward force increases with the yaw angle as well. It has a positive effect to the driving stability of the vehicle but the moderated downward force should be kept for the fuel economy of a vehicle.

• 한국전산유체공학회지
• /
• 제19권2호
• /
• pp.66-71
• /
• 2014

Aerodynamic design of a vehicle has very important meaning on the fuel economy, dynamic stability and the noise & vibration of a moving vehicle. In this study, the correlation of aerodynamic effect between two model vehicles moving inline on a road was studied with the basic SAE model vehicle. Drag and lift are two main physical forces acting on the vehicle and both of them directly effect on the fuel economy and driving stability of the vehicle. For the research, the distance between two vehicles is varied from 5m to 30m at the fixed vehicle speed, 100km/h and the side-wind was assumed to be zero. The main issue for this numerical research is on the understanding of the interaction forces; lift and drag between two vehicles formed inline. From the study, it was found that as the distance between two vehicles is closer, the drag force acting on both the front and rear vehicle decreases and the lift force has same trend for both vehicle. As the distance(D) is 5m, the drag of the front vehicle reduced 7.4% but 28.5% for the rear-side vehicle. As the distance is 30m, the drag of the rear vehicle is still reduced to 22% compared to the single driving.

• 한국철도학회논문집
• /
• 제16권3호
• /
• pp.169-174
• /
• 2013

고성능 EMU 열차의 형상 개선을 통한 공기저항 저감 효과를 알아보기 위하여 3차원정상 Navier-Stokes 방정식과 2방정식 난류 모델을 이용한 전산유체역학을 이용하여 수치해석을 수행하였다. 전산시뮬레이션에는 FLUENTTM ver.13과 Gambit 2.4.6이 사용되었으며, 기본 형상과 유선형으로 개선된 형상에 대하여 계산을 수행하였다. 또한, 터널 내 주행 시의 공기저항 특성을 살펴보기 위하여 개활지에서의 공기저항 계산도 수행하였으며, 차량 별 공기저항 기여도에 대한 분석도 수행되었다. 유선형으로 개선된 형상의 열차는 절편형 전두부와 돌출된 상부 및 하부구조를 가진 기본 형상 열차에 비하여 약 9.8%의 공기저항이 저감된 것을 확인하였으며, 공기저항 저감에 따른 주행저항의 저감은 시속 80km/h에서 약 4%에 이르는 것으로 나타났다.

• 한국군사과학기술학회지
• /
• 제22권4호
• /
• pp.527-535
• /
• 2019

Hanger in a rail-launched missile protrudes in general and causes to increase significant drag force. One method to avoid the significant increase of drag force is to apply fairings on the hanger. In this paper, sloping shaped fairing parameters of height, width, and length are optimized to minimize the drag force under subsonic speed region by examining three configurations of fairings : front-fairing only, rear-faring only, and the both front and rear fairing. We use Latin Hypercube Sampling method to determine the experimental points, and computational fluid dynamics with incompressible RANS solver was applied to acquire the data at sampling points. Then, we construct a meta model by kriging method. We find the best choice among three configurations examined : both front and rear fairing reduce the drag force by 63 % without the constraint of fairing mass, and front fairing reduced the drag force by 52 % with the constraint of hanger mass.

• 한국전산유체공학회지
• /
• 제18권3호
• /
• pp.8-13
• /
• 2013

Drag reduction of a running vehicle is very important issue for the energy savings and emission reduction of its power train. Especially for a solar powered electric vehicle, the drag reduction and weight lightening are two serious problems to be solved to extend its driving distance under the given energy condition. In this study, the ground effect of an airfoil shaped road vehicle was studied for an optimum body design of an ultra-light solar powered electric vehicle. Clark-Y airfoil type was adopted to the body shape of the model vehicle to reduce aerodynamic drag. From the study, it was found that the drag of the model vehicle was reduced as the height(h) between ground and the lower surface of the model vehicle was decreased. It is due to the reduction of the down-wash decreasing the induced drag of the vehicle. The lift was also decreased as the height decreased. It is due to the turbulent boundary layer developed beneath the vehicle body. The drag is classified into two types; the form and friction drag. The fraction of form drag to friction one is 76 to 24 on the model vehicle. As the height(h) of the model vehicle from the ground surface increases the form drag also increases but the friction drag is in reverse.

• International Journal of Aeronautical and Space Sciences
• /
• 제15권4호
• /
• pp.374-382
• /
• 2014

This paper presents the computational aerodynamic analysis of a long-endurance UAV that was developed by the Korea Aerospace Research Institute (KARI), named EAV-2. EAV-2 is a technical demonstrator of aerodynamically efficient design, as well as a hybrid electric-propulsion system for future long-endurance UAVs. We evaluated the aerodynamic characteristics of six low-Reynolds number airfoils, using a panel method code, XFOIL, to select an optimal airfoil for the long-endurance mission of EAV-2. The computational results by a CFD code, FLUENT, suggested that the aerodynamic performance of EAV-2 would be notably improved after adopting SG6043 airfoil, and modifying the fuselage design. This reduced the total drag by 43%, compared to that of a previous KARI model, EAV-1, at the target lift of $C_L=1.0$. Also, we achieved a drag reduction of approximately 14% by means of the low-drag fuselage configuration.