• International Journal of Naval Architecture and Ocean Engineering
• /
• v.3 no.4
• /
• pp.242-253
• /
• 2011

Skin frictional drag reduction efficiency of "stiff" compliant coating was investigated in a wind tunnel experiment. Flat plate compliant coating inserts were installed in a wind tunnel and the measurements of skin frictional drag and velocity field were carried out. The compliant coatings with varying viscoelastic properties had been prepared using different composition. In order to optimize the coating thickness, the most important design parameter, the dynamic viscoelastic properties had been determined experimentally. The aging of the materials (variation of their properties) during half a year was documented as well. A design procedure proposed by Kulik et al. (2008) was applied to get an optimal value for the coating thickness. Along with the drag measurement using the strain balance, velocity and pressure were measured for different coatings. The compliant coatings with the thickness h = 7mm achieved 4~5% drag reduction within a velocity range 30~40 m/s. The drag reduction mechanism of the attenuation of turbulence velocity fluctuations due to the compliant coating was demonstrated. It is envisioned that larger drag reduction effect is obtainable at higher flow velocities for high speed trains and subsonic aircrafts.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.965-980
• /
• 2014

This paper presents a new estimation method of full scale propulsive performance for the pulling type podded propeller. In order to estimate the drag of pod housing, a drag velocity ratio, which includes the effects of podded propeller loading and Reynolds number, is presented and evaluated through the comparison of model test and numerical analysis. By separating the thrust of propeller blade and the drag of pod housing, extrapolation method of pod housing drag to full scale is deduced, and correction method of propeller blade thrust and torque to full scale is presented. This study utilized the drag coefficient ratio of the pod housing as a measure for expanding it to full scale, but in order to increase the accuracy of performance evaluation, additional study is necessary on the method for the full scale expansion via separating the drag of pod body, strut and fin which consist the pod housing.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.3
• /
• pp.330-337
• /
• 1996

The effects of pump and temperature on drag reducing characteristics were investigated with a polymer(PAAM : Polyacrylamide) and three kinds of surfactants(CTAC, STAC, Habon-G) in fully developed turbulent pipe flows with various experimental parameters such as additive concentration(30~500ppm), pipe diameter(4.65mm, 10.85mm), Reynolds number($4{\times}10^4{\sim}10^5$) and working fluid temperature($20{\sim}80^{\circ}C$). The pump effect on PAAM was severe such that the drag reduction rates obtained with pump were decreased upto 30% as compared with those obtained with compressed air in 4.65mm test section. The temperature effect on PAAM was noticeably considerable, that is, the higher temperaute, the less drag reduction rate. On the other hand, no significant pump effect on the surfactants was observed. The drag reducing effectiveness of CTAC was totally lost in the temperature ragne of 60 to $80^{\circ}C$, whereas STAC and Habon-G kept their distinct drag reducing capability at a temperature of $80^{\circ}C$. This study clearly elucidated that for DHC application of drag reducing additives, the pump and temperature effects as well as additive concentration and pipe diameter should be carefully taken into consideration.

• Journal of the Korean Society for Railway
• /
• v.19 no.6
• /
• pp.709-716
• /
• 2016

To reduce the aerodynamic drag of high speed trains, aerodynamic drag of KTX-Sancheon was analyzed in detail according to individual components. Aerodynamic drag values of the power cars (front car, rear car) and bogies are about 42.9% and 10.1% of the total aerodynamic drag, respectively. For the aerodynamic drag reduction of a power-car, a nose shape optimization was conducted using the Broyden-Fletcher-Goldfarb-Shanno optimum method. Shape change of a power car and bogie fairing adaptation are used to reduce the aerodynamic drag of a car body. The aerodynamic drag of the optimized train-set dropped by 15.0% compared to the aerodynamic drag of the KTX-Sancheon; a running resistance reduction of 12% is expected at the speed of 350km/h.

• Tribology and Lubricants
• /
• v.30 no.2
• /
• pp.71-76
• /
• 2014

As the importance of transmission efficiency to reducing fuel consumption and conserving the environment rapidly increases, reducing the drag torque in an automotive wet clutch is emerging as an important issue in the automotive industry. The drag torque in a clutch occurs from viscous drag generated by automatic transmission fluid in the narrow gap between separate friction plates. In this study, the drag torques in an automotive wet clutch are investigated with respect to the angle and density of the grooves between separate friction plates by three-dimensional finite element simulation of a single set of wet clutch disks considering the two-phase flow of air and oil. The simulation results shows that the drag torque generally increases with the rotational speed to a critical point and then decreases at the high-speed regime. The grooves between the plates plays an important role in reducing the drag peak, and the inclined angle of the grooves affects the oil flow. The grooves with an angle of $50^{\circ}$ shows the lowest drag torques at both low and high speeds. The flow vectors inside the $50^{\circ}$ grooves shows clear evidence that the fluid flows out more easily from the grooves compared with the flow vectors inside grooves with lower angles. The simulation results shows that increasing the number of grooves (density of grooves) decreases the drag torque.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.373-379
• /
• 2001

When a train runs into a tunnel at high-speed, aerodynamic drag suddenly increases and the booming noise is generated at the exit of tunnel. The noise shape is very important to reduce the aerodynamic drag in tunnel as well as on open ground, and the micro-pressure wave that is a source of booming noise is dependent on nose shape, especially on area distribution. In this study, the nose shape has been optimized employing the response surface methodology and the axi-symmetric compressible Navier-Stokes equations. The optimal designs have been executed imposing various conditions of the aerodynamic drag and the micro-pressure wave on object functions. The results show that the multi-objective design was successful to decrease micro-pressure wave and aerodynamic drag of trains.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.253-258
• /
• 2001

Control of drag force on a circular cylinder using a detached splitter plate is numerically studied for laminar flow. A splitter plate with the same length as the cylinder diameter(d) is placed horizontally in the wake region. Its position is described by the gap ratio(G/d), where G represents the gap between the cylinder base point and the leading edge of the plate. The drag varies with the gap ratio; it has the minimum value at a certain gap ratio for each Reynolds number. The drag sharply increases past the optimum gap ratio; this seems to be related to the sudden change in the bubble size in the wake region. This trend is consistent with the experimental observation currently available in case of turbulent flow. It is also found that the net drag coefficient significantly depends on the variation of base suction coefficient.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.18-18
• /
• 2000

In the high lift devices specifications for surface smoothness requirements, as manufacturing tolerances, arise out of aerodynamic consideration to minimize drag. True optimization of tolerances is a multi-disciplinary problem involving fluid mechanics, device performance, manufacturing philosophy and life cycle costing. One of the reasons for degradation of wetted surface is discrete roughness as a consequence of manufacturing defects, collectively termed as one of the excrescences effect. Usually, excrescence drag arising out of discrete roughness is of considerable lower order of magnitude as compared to the total drag of the flight bodies. Nor was there adequate predicting tool to account for the extent of drag degradation. Estimation of excrescence drag remained as a state-of-the art based on experimental results.

• Particle and aerosol research
• /
• v.9 no.4
• /
• pp.271-277
• /
• 2013

This article reports the drag reduction phenomenon of aqueous suspensions containing carbon nanotubes (CNTs) flowing through horizontal tubes. Stable nanofluids were prepared by using a surfactant. It is found that the drag forces of CNT nanofluids were reduced at specific flow conditions compared to the base fluid. It is found that the friction factor of CNT nanofluids was reduced up to approximately 30 % by using CNT nanofluids. Increased kinematic viscosities of CNT nanofluids are suggested to the key factors that cause the drag reduction phenomenon. In addition, transition from laminar to turbulent flow is observed to be delayed when CNT nanofluids flow in a horizontal tube, meaning that drag reduction occurs at higher flow rates, that is, at higher Reynolds numbers.

• Journal of computational fluids engineering
• /
• v.8 no.3
• /
• pp.7-11
• /
• 2003

Accurate assessment of the effect of jet plume on the boattail pressure drag of transonic airbreathing missiles is very important to reduce drag and to satisfy the flight range and the required maneuver. Numerical results of drag analysis for boattail and base pressures due to jet plume are presented considering the turbulence modeling. Drag assessment due to the size of jet plume, the conditions of the exhaust gas, the configurations of the boattail, and transonic mach numbers is included.