• Archives of Craniofacial Surgery
• /
• v.15 no.2
• /
• pp.53-58
• /
• 2014

Background: Maxillomandibular fixation (MMF) is usually used to treat double mandibular fractures. However, advancements in reduction and fixation techniques may allow recovery of the premorbid dental arch and occlusion without the use of MMF. We investigated whether anatomical reduction and microplate fixation without MMF could provide secure immobilization and correct occlusion in double mandibular fractures. Methods: Thirty-four patients with double mandibular fractures were treated with open reduction and internal fixation without MMF. Both fracture sites were surgically treated. For bony fixations, we used microplates with or without wire. After reduction, each fracture site was fixed at two or three points to maintain anatomical alignment of the mandible. Interdental wiring was used to reduce the fracture at the superior border and to enhance stability for 6 weeks. Mouth opening was permitted immediately. Results: No major complications were observed, including infection, plate exposure, non-union, or significant malocclusion. Five patients experienced minor complications, among whom the only one patient experienced a persistant but mild malocclusion with no need for additional management. Conclusion: This study showed that double mandibular fractures correction with two-or three-point fixation without MMF simplified the surgical procedure, increased patient comfort, and reduced complications, due to good stability and excellent adaptation.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.4
• /
• pp.721-728
• /
• 2018

This paper introduces various linear block error correction code and compares performances of the correction circuits. As the risk of errors due to power noise has increased, ECC(: Error Correction Code) has been introduced to prevent the bit error. There are two representatives of ECC structures which are SEC-DED(: Single Error Correction Double Error Detection) and SEC-DED-DAEC(: Double Adjacent Error Correction). According to simulation results, the SEC-DED circuit has advantages of small area and short delay time compared to SEC-DED-DAEC circuits. In case of SED-DED-DAEC, there is no big difference between Dutta's and Pedro's from performance point of view. Therefore, Pedro's code is more efficient than Dutta' code since the correction rate of Pedro's code is higher than that of Dutta's code.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.4
• /
• pp.281-285
• /
• 2020

Oxide semiconductor devices have become increasingly important because of their high mobility and good uniformity. The channel length of oxide semiconductor thin film transistors (TFTs) also shrinks as the display resolution increases. It is well known that reducing the channel length of a TFT is detrimental to the current saturation because of drain-induced barrier lowering, as well as the movement of the pinch-off point. In an organic light-emitting diode (OLED), the lack of current saturation in the driving TFT creates a major problem in the control of OLED current. To obtain improved current saturation in short channels, we fabricated indium gallium zinc oxide (IGZO) TFTs with single gate and double gate structures, and evaluated the electrical characteristics of both devices. For the double gate structure, we connected the bottom gate electrode to the source electrode, so that the electric potential of the bottom gate was fixed to that of the source. We denote the double gate structure with the bottom gate fixed at the source potential as the BGFP (bottom gate with fixed potential) structure. For the BGFP TFT, the current saturation, as determined by the output characteristics, is better than that of the conventional single gate TFT. This is because the change in the source side potential barrier by the drain field has been suppressed.

• Journal of architectural history
• /
• v.27 no.6
• /
• pp.7-18
• /
• 2018

The purpose of this paper is to analyze the double stylobate of the three-story stone pagoda in Yeongnam region and to divide the types of arrangements of the body-stone and roof-stone and find their correlation. Research objects are 47 three-story stone pagodas in Yeongnam region which have accurate documents and plans. After dividing a double stylobate of three-story stone pagodas into a lower and upper stylobate, we classified each stylobate into a type of body-stone and roof-stone from an architectural point of view. Types of arrangement of body-stones are divided into methods of using the 'ㅡ' shaped stone and methods of using 'ㄱ' shaped stone in the corner. And types of arrangement of roof-stones are divided into methods of arranging stones in a row or in a grid pattern. As the size of the pagoda increases, 'ㄱ' shaped stones used for the body-stone and stones for the roof-stone are arranged in a grid pattern. As the size of the pagoda becomes smaller, the body-stone is consist of 'ㅡ' shaped stone, and the roof-stone is arranged in a row. As the construction year of the pagoda becomes later, the size of the pagoda becomes smaller and types of body-stone and roof-stone had been stereotyped. As a result, the size of the stone pagoda became smaller as constructed later, and the type of body-stone and roof-stone of the double stylobate appear differently according to the size of the pagoda.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.881-893
• /
• 2019

This paper proposes a practical sliding-mode controller design for shaping the impedances of cascaded boost-converter power decoupling circuits for reducing the second order harmonic ripple in photovoltaic (PV) current. The cascaded double-boost converter, when used as power decoupling circuit, has some advantages in terms of a high step-up voltage-ratio, a small number of switches and a better efficiency when compared to conventional topologies. From these features, it can be seen that this topology is suitable for residential (PV) rooftop systems. However, a robust controller design capable of rejecting double frequency inverter ripple from passing to the (PV) source is a challenge. The design constraints are related to the principle of the impedance-shaping technique to maximize the output impedance of the input-side boost converter, to block the double frequency PV current ripple component, and to prevent it from passing to the source without degrading the system dynamic responses. The design has a small recovery time in the presence of transients with a low overshoot or undershoot. Moreover, the proposed controller ensures that the ripple component swings freely within a voltage-gap between the (PV) and the DC-link voltages by the small capacitance of the auxiliary DC-link for electrolytic-capacitor elimination. The second boost controls the main DC-link voltage tightly within a satisfactory ripple range. The inverter controller performs maximum power point tracking (MPPT) for the input voltage source using ripple correlation control (RCC). The robustness of the proposed control was verified by varying system parameters under different load conditions. Finally, the proposed controller was verified by simulation and experimental results.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.15 no.6
• /
• pp.81-92
• /
• 2005

A novel public key cryptosystem that provides a double decryption mechanism is proposed at Asiacrypt '03 by Bresson, Catalano and Pointcheval based on the scheme proposed by Clamor and Shoup at Eurocrypt '02. Previous double decryrtion scheme is designed based on $Z_n^2$ where n=pq for two primes p,q. In this paper, we propose an efficient public key scheme with double decryption mechanism based on $Z_p^2_q$ for two primes p,q. Our scheme is more efficient an the previous schemes. Moreover, we review the previous schemes in a privacy point of view and propose a privacy enhanced double decryption scheme.

• Journal of Environmental Science International
• /
• v.13 no.6
• /
• pp.497-503
• /
• 2004

In this research, we have performed a T-test to see how the relationship between dependent variable or visual point level and independent variable or visual quantity is in order to clear up the correlation between pattern of visual point and visual quantity by the constituents of a view from a different visual point level and the results are as follows: 1) In case of the character of Mt. Uam landscape of the city, Uamsan is set as a fixed point and about a direction of view(D), the north is a datum point from which the range of direction is distributed within 1800 westwardly and the visual range(R) is also within 2000m. An elevation is an average of 7.40 and the average story of the buildings is 3.85. Here the height of a story is about 4m so the average of the visual point difference is estimated at 15.4m. 2) The type of visual point is divided into the intersection group and the front of the highly used public buildings group. Double intersection types account for about 78.80%(52 spots) which forms a majority part of LCP. 3) The analysis of the difference of visual point level divided by eye level and that of the top of the buildings has been proved that there's a sharp difference resulted from t-test at 1 % significant level. The significant difference of elevation from height difference(l5.93m), however, has not been shown. 4) From the result of T-test about visual quantity by the elements of a view from a different visual point level, the visual quantity of mountain(VQM), sky(VQS), ground(VQG) is significant at about 1% each and that of building(VQB) is at about 5%. The difference in visual quantity of a mountain by the visual point level is at about 4% which can meet a marginal level of LCP necessary for evaluation of mountainscape.

• Journal of Broadcast Engineering
• /
• v.2 no.1
• /
• pp.24-35
• /
• 1997

Basic and transmission video quality testing was performed in real-time mode using hardware video codec based on MPEG-2 MP@ML standard including subsequent transmitting and receiving satellite simulator unit. The double-stimulus Impairment scale method and the double-stimulus continous quality scale method based on CCIR 500-5 were used as an evaluation method. The whole digital broadcasting satellite system consisting of MPEG-2 codec, system mux/demux, channel codec, channel, modem, antenna, etc. was put into the overall video quality testbed and the basic and transmission error quality assessment was performed at various bitrates and BER for an integrated system performance evaluation. In transmission error video quality testing, transmission error video quality maintained on average above 3.9 point on the 5-point scale. The low-bit rate quality such as film mode(@2Mbps) highly depended on the statitical characteristics of video source and maintained on average around 2.7 point.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.13 no.1
• /
• pp.75-80
• /
• 2010

Intestinal duplication cysts are characterized by the attachment to some part of the gastrointestinal tract with which a blood supply is shared, and have an epithelial lining resembling some part of the alimentary tract. A 15-month-old female was admitted to our hospital with cyclic irritability, vomiting, and blood-tinged stool. The results of an ultrasound showed an ileocolic intussusception and a 1.3 cm cystic mass had double-wall sign and a Y-configuration with an adjacent ileal loop. She had a past history of two ileocolic intussusceptions. The cystic mass was considered to be a pathologic lead point, so resection and end-to-end anastomosis was performed. The gross and histologic evaluation of the specimen demonstrated a $2.4{\times}2.4$ cm cystic mass containing yellow mucoid fluid and the cyst wall was lined with intestinal and gastric mucosa and enclosed by a layer of muscle, which was shared with the adjacent ileum.

• Korean Journal of Applied Biomechanics
• /
• v.14 no.1
• /
• pp.27-40
• /
• 2004

The purpose of this study was to provide basic data for improving athletic performances by analyzing the kinematic variables of the Double Backward Somersault on the Parallel Bars through the 3D motion analysis. The subjects in this study were 5 male gymnasts who were ranked as national athletes. The results are as follows. 1. A total time(Mean Time) of performance showed $2.72{\pm}0.82\;sec$. and flight time to landing after releasing was 0.87sec.(mean). In order to perform better stable flying movement, the flight time should be increased. 2. In the change of velocity of the center of mass, when the increasing ascension velocity of the upper point was high, the position in the top point was high on releasing. 3. In the position variable of the center of mass, the mean of upper-bottom position in horizontal posture was $242.1{\pm}6.5cm$, $232.8{\pm}6.4cm$ in releasing, and $265.0{\pm}5.6cm$ in the highest point. This result is explained that the position of center of mass can be raised by using elastic power when wrist raised the bar in the releasing movement. 4. The angle of shoulder joint was $271.1{\pm}14.0$. Such a big angle influences a negative effect on the releasing velocity, because trunk is not a position in the enough vertical direction. 5. The ankle of hip joint in hand-standing was $191.1{\pm}5.9$, $118.8{\pm}5.3$ in releasing, and $122.3{\pm}5.3$ in taking on. Therefore, the result suggests that trunk should be straightly raised in taking on.