• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.2A
• /
• pp.191-197
• /
• 2008

For the efficient transmission of burst data in the time varying wireless channel, opportunistic scheduling is one of the important techniques to maximize multiuser diversity gain. In this paper, we propose a distributed opportunistic scheduling scheme for wireless LAN network. A proportional fair scheduling, which is one of the opportunistic scheduling schemes, is used for centralized networks, whereas we design distributed proportional fair scheduling (DPFS) scheme and medium access control with distributed manner. In the proposed DPFS scheme, each receiver estimates channel condition and calculates independently its own priority with probabilistic manner, which can reduce excessive probing overhead required to gather the channel conditions of all receivers. We evaluate the proposed DPFS using extensive simulation and simulation results show that DPFS obtains higher network throughput than conventional scheduling schemes and has a flexibility to control the fairness and throughput by controlling the system parameter.

• Structural Engineering and Mechanics
• /
• v.31 no.6
• /
• pp.737-749
• /
• 2009

The problem of estimating the dynamic response of a distributed parameter system excited by a moving vehicle with random initial velocity and random vehicle body mass is investigated. By adopting the Galerkin's method and modal analysis, a set of approximate governing equations of motion possessing time-dependent uncertain coefficients and forcing function is obtained, and then the dynamic response of the coupled system can be calculated in deterministic sense. The statistical characteristics of the responses of the system are computed by using improved perturbation approach with respect to mean value. This method is simple and useful to gather the stochastic structural response due to the vehicle-passenger-bridge interaction. Furthermore, some of the statistical numerical results calculated from the perturbation technique are checked by Monte Carlo simulation.

• Journal of Navigation and Port Research
• /
• v.27 no.5
• /
• pp.487-492
• /
• 2003

The paper describes on the implementation of marine casualty prediction model that is one of the main part of Korean MArine Casualty FOrecasting System (K-MACFOS). In this work, Cell Distributed Linear-In-the-Parameter (CD-LIP) model is proposed and discussed its usability with comparing Baltic model and revised LIP model. As evaluation results by regression analysis of variance, it is known that the CD-LIP model gives best performance to the marine casualty numerical D/B of the target sea area.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.255-259
• /
• 1989

A suboptimal output feedback controller is designed and applied to a flexible rotor bearing system in order to control the unstable or lilghtly damped vibrations. The reduced order model is the truncated modal equation of the distributed parameter system obtained through the singular perturbation. The instability problem arising from the spillover effects caused by the uncontrolled high frequency modes is prevented through the constrained optimization by incorporating the spillover term into the performance index. The efficiency of the proposed method is demonstrated experimentally with a flexible rotor by using a magnetic bearing.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2003.05a
• /
• pp.60-65
• /
• 2003

The paper describes on the implementation of marine casualty prediction model that is one of the main part of Marine Casualty Forecasting System (MCFS). In this work, Cell Distributed Linear-In-the Parameter (CD-LIP) model is developed and compared with Baltic model using regression analysis of variance. As comparing, it is known that the proposed CD-LIP model has less residual than the Baltic model and, it gives best performance to the marine casualty numeric D/B of target area.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.838-843
• /
• 2001

Internal damping plays an important role in some rotor dynamic systems with the use of various materials for shafts, for example, composite material. However, although the effects of internal damping have been investigated for a couple of decades, there are several different internal damping models in use, none of which are accepted as the most reliable model. The purpose of this paper is to compare the results of dynamic analysis of rotor systems with several different internal damping models. The exact dynamic element method is used to formulate and analyze the problem. The simulation results provided in this paper may be useful for the dynamic analysis of high rotor systems subject to significant internal damping.

• KIEE International Transaction on Systems and Control
• /
• v.2D no.2
• /
• pp.78-91
• /
• 2002

In the thermal power plant, there are six manipulated variables: main steam flow, feedwater flow, fuel flow, air flow, spray flow, and gas recirculation flow. There are five controlled variables: generator output, main steam pressure, main steam temperature, exhaust gas density, and reheater steam temperature. Therefore, the thermal power plant control system is a multinput and output system. In the control system, the main steam temperature is typically regulated by the fuel flow rate and the spray flow rate, and the reheater steam temperature is regulated by the gas recirculation flow rate. However, strict control of the steam temperature must be maintained to avoid thermal stress. Maintaining the steam temperature can be difficult due to heating value variation to the fuel source, time delay changes in the main steam temperature versus changes in fuel flow rate, difficulty of control of the main steam temperature control and the reheater steam temperature control system owing to the dynamic response characteristics of changes in steam temperature and the reheater steam temperature, and the fluctuation of inner fluid water and steam flow rates during the load-following operation. Up to the present time, the Proportional-Integral-Derivative Controller has been used to operate this system. However, it is very difficult to achieve an optimal PID gain with no experience, since the gain of the PID controller has to be manually tuned by trial and error. This paper focuses on the characteristic comparison of the PID controller and the modified 2-DOF PID Controller (Two-Degrees-Freedom Proportional-Integral-Derivative) on the DCS (Distributed Control System). The method is to design an optimal controller that can be operated on the thermal generating plant in Seoul, Korea. The modified 2-DOF PID controller is designed to enable parameters to fit into the thermal plant during disturbances. To attain an optimal control method, transfer function and operating data from start-up, running, and stop procedures of the thermal plant have been acquired. Through this research, the stable range of a 2-DOF parameter for only this system could be found for the start-up procedure and this parameter could be used for the tuning problem. Also, this paper addressed whether an intelligent tuning method based on immune network algorithms can be used effectively in tuning these controllers.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.4
• /
• pp.73-80
• /
• 2010

The grounding impedance is not lowered by expanding the dimension of the grounding electrode, and the length of grounding electrode which shows the minimum value of the grounding impedance for each condition of frequency and soil characteristics is existent, and it is defined as Critical Length. In this paper, a new distributed parameter circuit model considering the condition of the multi-layered soil structures was proposed, and the grounding impedance and critical length of the vertical grounding electrode were analyzed by using the newly proposed simulation model and the MATLAB program. As a consequence, it was found that the effect of the soil structure on the frequency-dependent grounding impedance and critical length of the vertical grounding electrode is significant. It is desirable to consider the soil structure in optimal design of the grounding system.

• Journal of Korean Institute of Industrial Engineers
• /
• v.33 no.1
• /
• pp.70-75
• /
• 2007

This paper discusses condition based preventive replacement for deteriorating systems. The system continuouslydeteriorates in time and fails at any deterioration level which is always monitored, It is replaced at failure or atsome deteriorated level preventively before failure. The deterioration process is represented by a Weibulldistribution with a time-linear scale parameter. The cost rate function is formed considering replacement costand opportunity loss cost and deterioration dependent failure distribution, If the system has an increasingdeterioration dependent failure rate, the optimal deterioration level for preventive replacement can be determinedfrom minimizing the cost rate. An illustrative example is given for a Weibull deterioration dependent failuredistribution.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.2
• /
• pp.27-34
• /
• 1999

The growth-strain method was used for shape optimization, which carries out the optimization by distributing uniformly the distributed parameter such as von Mises stress and shear strain energy density. Shape optimization is carried out by iteration of stress analysis and growth strain analysis. In this study, the effect of growth ratio in the method was investigated and then the range of the adequate value of the growth ratio was determined. Also the growth-strain method was improved by applying the linear PID control theory in order to control volume required by a designer. Finally, an automatic shape optimization system was built up by the improved growth-strain method with a commercial software using finite element method. The effectiveness and practicability of the developed shape optimization system was verified by some examples.