• 열처리공학회지
• /
• 제12권1호
• /
• pp.55-65
• /
• 1999

Graphitization of cementite in high carbon steels at subcritical temperature is reported. We have studied about the effects of Ni in these steels on graphitization. The chemical compositions of the specimens were Fe-(0.54, 0.7)%-C-1.0%Si-0.1%Mn-(0.2~1.0)%Ni. After annealing at $650^{\circ}C$, $680^{\circ}C$ and $700^{\circ}C$ during various time the microstructures and hardness change were observed. In order to recover the initial hardness of high carbon steel, dissolution treatment of graphite was performed at $870^{\circ}C$. In case of 0.7%C steel, graphitization was accelerated rather 1.0%Ni addition steel than 0.2% and 0.54%Ni addition steels but the graphite is coarser. In case of 0.54%C-0.2%Ni steel, graphite particles were distributed relatively homogeniously and finely. Nickel addition promotes graphitization of these steels but makes graphite blocky.

• 신재생에너지
• /
• 제4권1호
• /
• pp.11-18
• /
• 2008

In-situ lithiated NiO has been manufactured as a conventional cathode material of molten carbonate fuel cell (MCFC), however this material has a weakness for commercialization of MCFC because NiO is spontaneously dissolved into the electrolyte under MCFC operating conditions, resulting in short circuit between cathode and anode. In this research, therefore, $Co(OH)_2$-coated Ni powder was prepared by precipitation method with controlling pH at low temperature and atmospheric pressure. Modified cathode was fabricated by a conventional tape casting method and sintered at 700$^{\circ}C$ in a $H_2/N_2$ atmosphere, Based on characterization result, Pore size distribution and porosity was suitable for the cathode of MCFC. According to the result of dissolution, Ni solubility of modified cathode was 33% lower than that of conventional cathode. In addition, modified electrode showed a good performance from the single cell operation.

• Macromolecular Research
• /
• 제10권2호
• /
• pp.60-66
• /
• 2002

The morphology, dynamic mechanical behavior and fracture behavior of polyetherimide (PEI)/dicyanate semi-interpenetrating polymer networks (semi-IPNs) with a morphology spectrum were analyzed. To obtain the morphology spectrum, we disported PEI particles in the procured dicyanate resin containing 300 ppm of zinc stearate catalyst. The semi-IPNs exhibited a morphology spectrum, which consisted of nodular spinodal structure, dual-phase morphology, and sea-island type morphology, in the radial direction of each dispersed PEI particle due to the concentration gradient developed by restricted dissolution and diffusion of the PEI particles during the curing process of the dicyanate resin. Analysis of the dynamic mechanical data obtained by the semi-IPNs demonstrated that the transition of the PEI-rich phase was shifted toward higher temperature as well as becoming broader because of the gradient structure. The semi-IPNs with the morphology spectrum showed improved fracture energy of 0.3 kJ/$m^2$, which was 1.4 times that of the IPNS having sea-island type morphology. It was found that the partially introduced nodular structure played a crucial role in the enhancement of the fracture resistance of the semi-IPNs.

• Nuclear Engineering and Technology
• /
• 제46권3호
• /
• pp.431-438
• /
• 2014

The effect of various pH agents on the corrosion behavior of carbon steel was investigated under a simulated secondary water chemistry condition of a pressurized water reactor (PWR) in a laboratory, and the steel's corrosion performance was compared with the field data obtained from Uljin NPP unit 2 reactor. All tests were carried out at temperatures of $50^{\circ}C-250^{\circ}C$and pH of 8.5 - 10. The pH at a given temperature was controlled by adding different agents. Laboratory data indicate that the corrosion rate of carbon steel decreased as the pH increased under the test conditions and the highest corrosion rate was measured at $150^{\circ}C$. This high corrosion rate may be related to high dissolution and instability of Fe oxide ($Fe_3O_4$) at $150^{\circ}C$. It was also found that an addition of ethanolamine (ETA) to ammonia was more effectivefor anticorrosion than ammonia alone, and that mixed treatment reduced 50% of iron or more at pHs of 9.5 or higher, especially in the steam generator (SG) and the moisture separator & re-heater (MSR).

• Corrosion Science and Technology
• /
• 제6권6호
• /
• pp.304-307
• /
• 2007

As to the reflection electrode of LCD (liquid crystal displays), silver-copper-gold alloy (hereafter, it is called as ACA (Ag98%, Cu1%, Au1%)) is an effective material of which weathering resistance can be improved more compared with pure silver. However, there is a problem that gold remains on the substrate as residues when ACA is etched in cerium ammonium nitrate solution or phosphoric acid. Gold can not be etched in these etchants as readily as the other two alloying elements. Gold residue has actually been removed physically by brushing etc. This procedure causes damage to the display elements. Another etchant of iodine/potassium iodide generally known as one of the gold etchants can not give precise etch pattern because of remarkable difference in etching rates among silver, copper and gold. The purpose of this research is to obtain a practical etchant for ACA alloy. The results are as follows. The cyanogen complex salt of gold generates when cyanide is used as the etchant, in which gold dissolves considerably. Oxygen reduction is important as the cathodic reaction in the dissolution of gold. A new etchant of sodium cyanide / potassium ferricyanide whose cathodic reduction is stronger than oxygen, can give precise etch patterns in ACA alloy swiftly at room temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.310-313
• /
• 2002

Structures obtained with a direct boning of two FZ silicon wafers joined in such a way that a smooth surface of one wafer was attached to the grooved surface of the other were studied. A square net of grooves was made with a conventional photo lithography process. After high temperature annealing the appearance of voids and the rearrangement of structural defects were observed with X-ray diffraction topography techniques. It was shown that the formation of void free grooved boundaries was feasible. In the cases when particulate contamination was prevented, the voids appeared in the grooved structures could be eliminated with annealing. Since it was found that the flattening was accompanied with plastic deformation, this deformation was suggested to be intensively involved in the process of void removal. A model was proposed explaining the interaction between the structural defects resulted in "a dissolution" of cavities. The described processes may occur in grooved as well as in smooth structures, but there are the former that allow to manage air traps and undesirable excess of dislocation density. Grooves can be paths for air leave. According to the established mechanisms, if not outdone, the dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.

• 전기화학회지
• /
• 제11권4호
• /
• pp.227-241
• /
• 2008

This article involves a unified treatment of equilibrium thermodynamics of the chemical reaction coupled with other interfacial (phase boundary) reactions. The modified (restrictive) chemical potential ${\mu}_k^+$, such as electrochemical potential, hydrostatic-chemical (mechanochemical) potential (exceptionally in the presence of the pressure difference) and surface-chemical potential, was first introduced under the isothermal and isobaric conditions. This article then enlightened the equilibrium conditions in case where the release of chemical energy is counterbalanced by the supply of electrical energy, by the supply of hydrostatic work (exceptionally in the presence of ${\Delta}p$), and finally by the release of surface energy, respectively, at constant temperature T and pressure p in terms of the modified chemical potential ${\mu}_k^+$. Finally, this paper focussed on the difference between chemical and electrochemical equilibria based upon the fundamentals of the isothermal and isobaric equilibrium conditions described above.

• Journal of the korean society of oceanography
• /
• 제33권1-2호
• /
• pp.8-17
• /
• 1998

Paleoceanographic history of the East Sea is reconstructed based on several environmental parameters (coarse fraction content, planktonic foraminifera/benthic foraminifera ratio, fragmentation and assemblages of planktonic foraminifera, and coiling ratio of Neogloboquadrina pa-chyderma, etc,) of the late Quaternary sediments obtained from the Ulleung Basin. N. pa-chydeyma and Globigerina bulloides are dominant species (greater than 90% in abundance)among the total planktonic foraminifera assemblages in the late Quaternary sediments. The benthic foraminifera rarely occurred throughout the cores. Sinistrally-coiled specimens of N. pa-chyderma representing cold water temperature are observed more abundantly than dextrally-coil-ed ones. In addition, the sinistrally-coiled N, pachydeyma showed more the amount at the lower part of the cores than at the upper part suggesting the restriction of the Tsushima Warm Current into the East Sea during glacial period. G. bulloides, a species representative of upwelling condition, shows more abundant occurrence in the sediments of Core 941013 than those of Core 941006. This implies that Core 941013 is more influenced by upwelling than Core 941006. The upper part of the two cores contain more fragmentation of planktonic foraminifera suggesting significant dissolution by corrosive bottom wafer. Ascending CCD also played an important role for the absence of planktonic foraminifera at the upper part of the cores.

• 한국세라믹학회지
• /
• 제49권1호
• /
• pp.100-104
• /
• 2012

Barium zincoborate (BZB) glass was added to $Ba_{0.5}Sr_{0.5}TiO_3$, and sintered at $875^{\circ}C$ for 2 h in air. When the BZB glass was added in quantities ranging from 15 to 20 wt%, the relative bulk density ranged from 93.1% to 94.2%, while the density decreased to roughly 81% thereafter up to 30 wt% glass addition. Quantitative XRD analysis showed that the $Ba_{0.5}Sr_{0.5}TiO_3$ filler was significantly dissolved into the BZB glass. However, no secondary phase was identified by XRD up to 30 wt% glass addition. The dielectric constant was about 130 to 140 at 1MHz up to 20 wt% BZB glass addition, while it decreased to about 60 thereafter, which may be ascribed to decreased density, partial dissolution of the $Ba_{0.5}Sr_{0.5}TiO_3$, and associated changes in the glass composition. The dielectric loss of the 20 wt% glass added specimen was 0.008.

• 한국분말재료학회지
• /
• 제24권1호
• /
• pp.29-33
• /
• 2017

Titanium carbide (TiC) powders are successfully synthesized by carburization of titanium hydride ($TiH_2$) powders. The $TiH_2$ powders with size lower than $45{\mu}m$ (-325 Mesh) are optimally produced by the hydrogenation process, and are mixed with graphite powder by ball milling. The mixtures are then heat-treated in an Ar atmosphere at $800-1200^{\circ}C$ for carburization to occur. It has been experimentally and thermodynamically determined that the de-hydrogenation, "$TiH_2=Ti+H_2$", and carburization, "Ti + C = TiC", occur simultaneously over the reaction temperature range. The unreacted graphite content (free carbon) in each product is precisely measured by acid dissolution and by the filtering method, and it is possible to conclude that the maximal carbon stoichiometry of $TiC_{0.94}$ is accomplished at $1200^{\circ}C$.