• Journal of Pharmaceutical Investigation
• /
• v.5 no.3
• /
• pp.58-65
• /
• 1975

In the preparation of prednisolone tablets, when microfine cellulose$(Elcema^{\circledR})$ was used as diluents, stability and physical characteristics of prednisolone tablets are as follows; 1. Weight of the plain $Elcema^{\circledR}$ tablets increased by 75% of relative humidity and hardness was weakend, but the temperature $(60^{\circ}C)$ caused no change of thickness and decreased the weight and hardness. 2. In experimental tableting of prednisolone tablets, the addition of $Elcema^{\circledR}$ caused no difficulty in direct compression method, and the shortening of the disintegration time and increase of the hardness were satisfactory. 3. Dissolution rate test exhibited the result similiar to disintegration test. 4. In the comparison test of $Elcema^{\circledR}$ and $Avicel^{\circledR}$ as adjuvants the physical constants of prednisolone tablets showed nearly a similar tendency.

• Journal of the Korean Ceramic Society
• /
• v.27 no.3
• /
• pp.383-388
• /
• 1990

Hydraulic properties of CA2-based clinker synthesized by Hydration-Burning Method was studied by calorimetry, analysis of suspension, thermogravimetry, scanning electron microscopy and X-ray diffractometry. Hydraulic properties of the clinker was so activated that heat of hydration of the clinker evolved faster than that of CA synthesized by conventional method. In suspension of W/C=33, dissolution of the clinker began at nearly same time as that of CA, but precipitation of AH3 and rise of [OH-] occurred fairly faster in the suspension of the clinker than that of CA. From the beginning of hydration, AH3 was produced and became a main phase of the hydrate with minor phase of CAH10 and C2AH8, but C3AH6 was not produced at ambient temperature.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.4
• /
• pp.453-462
• /
• 2015

A critical review on existing creep theories in calcium-silicate-hydrate (C-S-H) is presented with an emphasis on several fundamental questions (e.g. the roles of water, relative humidity, temperature, atomic ordering of C-S-H). A consensus on the rearrangement of nanostructures of C-S-H as a main consequence of creep, has almost been achieved. However, main disagreement still exists on two basic aspects regarding creep mechanisms: (1) at which site the creep occurs, like at interlayer, intergranular, or regions where C-S-H has a relatively higher solubility; (2) how the structural rearrangement evolutes, like in a manner of interlayer sliding, intra-transfer of water at various scales, recrystallization of gelled-like particles, or dissolution-diffusion-reprecipitation at inter-particle boundary. The further understanding of creep behavior of C-S-H relies heavily on the appropriate characterization of its nanostructure.

• Journal of Industrial Technology
• /
• v.21 no.A
• /
• pp.351-355
• /
• 2001

This research was carried out to find out the possibility of using Faraday's law in analyzing the electrocoagulation system. Bench-scale reactor equipped with aluminum electrode plates was operated using synthetic wastewater which received sodium chloride for conductivity adjustment. Phosphate was added to the wastewater to induce the precipitation with Al. The amount of aluminum dissolved from the electrodes could be predicted by Faraday's law with a difference less than 5%. This difference was greater at a higher electric current, probably due to the increased solution temperature. However, effect of pH on the dissolution of the aluminum was negligible. The result of this study suggested that the operating condition of electrocoagulation system could be developed using the Faraday's law when the pollutant concentration is given.

• Archives of Pharmacal Research
• /
• v.27 no.3
• /
• pp.357-360
• /
• 2004

Four crystal forms of ketorolac have been obtained by recrystallization in organic solvents under variable conditions. Different ketorolac polymorphs and pseudo polymorph were characterized by X-ray powder diffraction crystallography (XRD), Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). In the dissolution studies in water at $37{\pm}0.5^{\circ}C$ four crystal forms showed different patterns. The solubility of Form I were the highest. The solubility decreased in rank order: Form I> Form II > Form III > Form IV. Form land Form III were shown to have a good physical stability at room temperature for 60 days. However, Form II is converted to Form III and Form IV is converted to Form I after 60 days storage. Therefore, these observations indicate that crystalline polymorphism for ketorolac is readily inter-convertible and the relationship may have to taken into consideration in the formulation of the drug.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.274-276
• /
• 2006

Weldability of high Cr ferritic steel for $620^{\circ}C$ grade turbin casing were investigated. The effect of carbon content on the cold and hot cracking susceptibility and HAZ softening was determined. The cast steel with higher carbon content showed higher HAZ hardness because of the dissolution of cabonitrides during welding thermal cycle. Moreover, it showed higher solidification cracking sensitivity because of the little S-ferrite formation in weld metal. Both steels showed HAZ softening at $900^{\circ}C$ peak temperature after PWHT.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.1
• /
• pp.44-56
• /
• 1997

Influence of electrochemical etching conditions on capacitance gain of aluminium electrolytic on capacitor foil has been investigated by etching cubic textured high purity aluminum foil in dilute hydrochloric acid. Uniformly distributed etch pit tunnels on aluminum surface have been obtained by pretreatment aluminium foil in 10% NaOH solution for 5 minutes followed by electrochemical etching. Electrostatic capacitance of etched aluminium foil anodized to high voltage increased with the increase of current density, total charge, temperature and concentration of electrolyte up to maximum CV-value and then deceased. Election optical observation of the etched foil revealed that the density of etch of etch pits increased with the increase of current density and concentration of electrolyte. this increase of etch pit density enlarged of the increase of capacitance. However, abnormal high current density and high electrolyte concentration induced the local dissolution of the foil surface which resulted the decrease of foil capacitance.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.1
• /
• pp.3-11
• /
• 1998

Molten Carbonate Fuel cell is a promising new type electric power generation system which can achieve high efficiency, lower matrrial cost and high operating temperature Making internal reforming possible. Although the development of the MCEC is progressing rapidly toward commercialization, two important tchological problems such as dissolution of NiO cathode and not corrosion of metallic separator plate must be resolved. Because MCFC is operated at $650^{\circ}C$ and the electrolyte is very corrosive, corrosion-resistance of separator plated against oxidation abd molten carbonate is required. Al-coating on separator material for corrosion-resistance was carried out by painting, thermal spraying. hot dipping and vacuum vapour deposition. The corrosion of Al-coated STS 316S and 316L in molten carbonate at $700^{\circ}C$was studied. Vacuum vapour deposition and thermal spraing for Al-coating on STS 310S and 316L were the most effective methods for protecting thestainless steel corrosion in molten carbonate.

• Journal of Pharmaceutical Investigation
• /
• v.19 no.1
• /
• pp.29-37
• /
• 1989

For the prevention of the aggregation during microencapsulation, the effects and role of polyisobutylene(PIB), as a protective colloid, were studied. The effects of sealant treatment on the microencapsulation were studied. Methyldopa was microencapsulated with ethylcellulose (EC) by polymer deposition from cyclohexane by temperature change using PIB. The EC-microencapsulated methyldopa was sealed with spermaceti. The dissolution of methyldopa was influenced by the drug to wall ratio. When PIB was used, low aggregation of microcapsules occurred and the surface was smooth with a few pores. Treatment of microcapsules with spermaceti retarded the release of methyldopa, the release being affected by the percentage of sealant used and the particle size of the product.

• Journal of the Korean institute of surface engineering
• /
• v.12 no.3
• /
• pp.167-173
• /
• 1979

The structure of anodic aluminium oxide films formed in 2% oxalic asid at constant temperature was studied by the oid of the transmission and replica electron microscopy. Far the initial stage of oxidations, it is observed that pores are initiated from lattice defects as subgrain boundaries, and then spread radially. Some pores merge each other and the others cease to grow until the current density reaches to the steady state. The pore diameter and the cell size are proportional to the anodizing voltages, and it is considered that the pore initiation and growth are largely controlled by the field - assisted oxide dissolution.