• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.82-89
• /
• 2007

This paper presents a coplanar waveguide fed L-planar type monopole antenna which covers ultra wideband(UWB) region of 3.1 GHz to 10.6 GHz. The proposed UWB L-planar type monopole antenna is designed and implemented on the organic substrates( ${\varepsilon}_{r}=3.38,\;@10\;GHz$). The radiation elements, feed line, and ground planes of the antenna are printed on the same conductive layer of the substrates. The bandwidth of the proposed antenna is measured in the range of 3.0 GHz to 11.0 GHz. The measured radiation patterns are symmetrical in E-plane and omni-directional in H-plane. Antenna gains ranges from 1.4 dBi to 4.6 dBi. The proposed UWB antenna shows that the structure is adequate for the design of RFIC.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.273-279
• /
• 2009

In this paper, an antenna which has dipole-like radiation pattern and low profile is proposed. The antenna is composed of four elements slot array based on L-shaped 0.43 $\lambda_g$ slot element. It presents a omni-directional radiation patter in the azimuth plane and has a null toward broad-side direction. In the design, a small mono-pole antenna which acts as a large capacitance element, combined with the partially removed ground plane by four L-shaped slots. As a result, these structure act as a LC resonator for radiation. The measured result shows, the impedance bandwidth(VSWR$\leq$2) of the proposed antenna is 60 MHz(2.35$\sim$2.41 GHz). The measured maximum radiation gain and efficiency of proposed antenna is 0.02 dBi, 56.7 % at center frequency 2.38 GHz, respectively. The proposed antenna can be applied to wireless tan access point system.

• Journal of Communications and Networks
• /
• v.10 no.4
• /
• pp.412-421
• /
• 2008

We observe simultaneous transmission of relay stations (RSs) allowed in current IEEE 802.16j draft standard for multi-hop relay networks may involve severe interference among the RSs, hence leading to throughput degradation. Allowing only 1/3 of the RSs to simultaneously transmit instead of 1/2 RSs as in the current draft standard reduces the interference but results in reduced throughput. To remedy this problem, we devise schemes to incorporate network coding at link-layer level (decode-and-forward) into the simultaneous transmission of RSs. Data movement is rearranged to maximize coding gain. Formula is derived to dictate exact movement of packets traveling between base station (BS) and mobile stations (MSs) via intermediate RSs. The frame structure in the current IEEE 802.16j draft standard does not allow broadcast needed for network coding. We devise a new frame structure which supports the broadcast. A new R-MAP (pointers to the burst data) is introduced to implement the broadcast. Since our new frame structure is used only for BS to RS or RS to RS communication, our schemes retain backward compatibility with legacy MSs based on IEEE 802.16e standard. Simulation based on simple configuration of RSs shows considerable improvement in terms of system throughput and round trip delay. For a 4-hop relay network with 1 BS and 4 RSs with symmetric traffic in uplink (UL) and downlink (DL), throughput is improved by 49% in DL and by 84% in UL traffic compared with IEEE 802.16j draft standard under the assumption that omni-directional antennae are used in BS and RSs.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.512-521
• /
• 2017

Telemetry ground station use very high gain directional antenna systems that are sensitive to interference from other RF communication systems, Without appropriate interference protection, these systems could be severely impacted or even rendered useless for mission support. In ECC, we suggested ans interference analysis method between LTE-TDD system and telemetry ground station using 2.3GHz. In this paper, based on the interference analysis scenario considered in Electronic Communication Committee, We have derived mutual coexistence separation distance between telemetry ground station and LTE-TDD system(Base station, User equipment) in Spatial domain.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.265-272
• /
• 2011

This study designed and manufactured "a DVOR virtual signal generator" to make the monitoring system of preliminary Doppler VHF Omni-directional Radio Range(DVOR) run like its real operation status in a narrow space in order to study "a DVOR virtual monitoring system". The designed and manufactured DVOR virtual signal generator is suitable for the specification of signal that is generated in the currently running equipment. In addition, it is possible to control operation conditions of equipment by using parameter variables, and the circuit construction is largely divided into the input part, the modulation part, the high-gain amplifier, and the power part. "The DVOR virtual monitoring system using the virtual signal designed and implemented in this study is very suitable to be used for low-cost actual education as it can construct the operation status like the real situation in a narrow space without using an actual system like an antenna generating side band.

• Journal of Advanced Navigation Technology
• /
• v.25 no.3
• /
• pp.223-228
• /
• 2021

In this paper, we proposed a slot-type antenna with microstrip feed embedded in a PCB for Zigbee communication (2.4 ~ 2.484 GHz). The proposed antenna is designed on a FR-4 substrate with dielectric constant 4.3, thickness of 1.6 mm, and size of 50×65 mm². Through simulations, trends of design parameters are analyzed and optimized, and the proposed antenna composed with three slots satisfy the frequency band. The measured impedance bandwidths (|S₁₁| ≤ -10 dB) of fabricated antenna are 900 MHz (2 ~ 2.9 GHz) in Zigbee frequency band. In addition, the radiation pattern showed omnidirectional characteristics for E and H-planes, and the gain of antenna in Zigbee frequency band was 1.782 dBi.

• Journal of IKEEE
• /
• v.25 no.4
• /
• pp.607-612
• /
• 2021

This paper presents a novel CPW-fed UWB monopole paper antenna made by paper and copper tape. Through the simulation, the optimized antenna design parameters were obtained, and an antenna having an omni-directional radiation pattern and a gain of 2.2 dBi or more in the UWB frequency band of 3.1-10.6 GHz was designed. The antenna was manufactured using general A4 paper and copper tape, and the measurement result satisfies the return loss of -10dB or less in the UWB frequency band and confirm that the return loss characteristic was maintained even when the antenna plane was bent by 3 mm in the longitudinal direction. The proposed antenna is a wearable device that can provide services in the UWB band, and can be manufactured inexpensively by printing it with a conductive print on paper. So it can be used as a wearable antenna for UWB communication in various application fields such as logistics and disposable terminals.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.1
• /
• pp.127-134
• /
• 2022

A modified folded monopole slot antenna for 3G WCDMA (1.91 ~ 2.17 GHz), 4G LTE (2.17 ~ 2.67 GHz), 3.5 GHz 5G (3.42 ~ 3.7 GHz) and Wi-Fi dual band (2.4 ~ 2.484 GHz / 5.15 ~ 5.825 GHz) was proposed for the first time. The proposed antenna is designed and fabricated on a FR-4 substrate with dielectric constant 4.3, thickness of 1.6 mm, and size of 35 × 60 mm². The measured impedance bandwidth of the proposed antenna is 2910 MHz(1.84 ~ 4.75 GHz) and 930 MHz(5.11 ~ 6.04 GHz), antenna gain in each frequency band is from 1.811 to 3.450 dBi. In particular, it was possible to obtain a commercially suitable omni-directional radiation pattern in all frequency bands of interest.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.1
• /
• pp.103-107
• /
• 2024

This paper is a study on a triangle patch antenna using a rectangle slot and strip conductor. The length and spacing of the slot were adjusted to confirm the characteristics of the triangle patch antenna with rectangle slot, and the area and shape of the radiation patch were changed to triangle, rectangle, and hexagon for impedance matching. The HFSS simulator was used to check the antenna parameter characteristics, and the antenna size was 26 mm ×26 mm. In this proposed antenna, the simulation frequency range with VSWR of 2 or less was 5.27 to 6.24 GHz. The bandwidth was 970 MHz. The frequency range of the fabricated antenna was 5.24 to 6.38 GHz, and the bandwidth 1140 MHz. The maximum radiation gain is 5.01 dBi. It was confirmed that all radiation patterns had directional characteristics.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1050-1060
• /
• 2009

In this paper, a X-Band T/R-module for SAR(Synthetic Aperture Radar) systems based on active phased array antennas is designed and fabricated. The T/R modules have a and width of more than 800 MHz centered at X-Band and support dual, switched polarizations. The output power of the module is 7 watts over a wide bandwidth. The noise figure is as low as 3.9 dB. Phase and amplitude are controlled by a 6-bit phase shifter and a 6-bit digital attenuator, respectively. Further the fabricated T/R module has est and calibration port with directional coupler and power divider. Highly integrated T/R module is achieved by using LTCC(Low Temperature Co-fired Ceramic) multiple layer substrate. RMS gain error is less than 0.8 dB max. in Rx mode, and RMS phase error is less than $4^{\circ}$ max. in Rx/Tx phase under all operating frequency band, or the T/R module meet the required electrical performance m test. This structure an be applied to active phase array SAR Antennas.