• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.99.1-99.1
• /
• 2012

The thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4 - 1.6 eV and a large absorption coefficient of ~104 $cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative aqueous chemical approach based on chemical bath deposition (CBD) method for large area deposition of CZTS thin films. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and some factors like triethanolamine, ammonia, temperature which strongly affect on the morphology of CZTS film.

• 한국재료학회지
• /
• 제15권8호
• /
• pp.543-547
• /
• 2005

Organic electroluminescence devices were made from 1,4-bis-(9-anthrylvinyl)benzene (AVB) and 1,4-bis-(9-aminoanthryl)benzene (AAB) anthracene derivatives. Device structure was ITO/AVB/PANI(EB)/Al (multi-layer device) and ITO/AAB:DCM/Al(single-layer device). In these devices, AVB, polyaniline(emeraldine base) (PANI(EB)) and AAB were used as the emitting material. 4-(dicyanomethylene)-2-methyl-6-p-(dimethylamino)styryl-4H -pyran(DCM) was used as red fluorescent dopant. We studied change of fluorescence wavelength with concentration of DCM doped in AAB. The ionization potential (IP) and optical band gap (Eg) were measured by cyclic voltammetry and UV-visible spectrum. We compared with difference of emitting wavelength between photoluminescence and electroluminescence spectrum. In case of the multi-layer device, PANI and AVB EL spectra have similar wave pattern to each PL spectrum and when PAM and AVB were used at the same time, and multi-layer device showed that a balanced recombination and radiation kom PANI and AVB. In case of the single-layer device, with the increase of DCM concentration, the blue emission decreases and red emission increases. This indicates that DCM was excited by the energy transfer from AAB to DCM or the direct recombination at the dopant sites due to carrier trapping, or both. The device with $1.0wt\%$ DCM concentration gave white light.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.24.1-24.1
• /
• 2009

The zinc oxide (ZnO) material as the II-VI compound semiconductor is useful in various fields of device applications such as light-emitting diodes (LEDs), solar cells and gas sensors due to its wide direct band gap of 3.37eV and high exciton binding energy of 60meV at room temperature. In this study, the ZnO nanorods were deposited onto homogenous buffer layer/Si(100) substrates by a hydrothermal synthesis. The Effects of the buffer layer annealing and post annealing temperature on the structural and optical properties of ZnO nanorods grown by a hydrothermal synthesis were investigated. For the buffer layer annealing case, the annealed buffer layer surface became rougher with increasing of annealing temperature up to $750^{\circ}C$, while it was smoothed with more increasing of annealing temperature due to the evaporation of buffer layer. It was found that the roughest surface of buffer layer improved the structural and optical properties of ZnO nanorods. For the post annealing case, the hydrothermally grown ZnO nanorods were annealed with various temperatures ranging from 450 to $900^{\circ}C$. Similarly in the buffer layer annealing case, the post annealing enhanced the properties of ZnO nanorods with increasing of annealing temperature up to $750^{\circ}C$. However, it was degraded with further increasing of annealing temperature due to the violent movement of atoms and evaporation. Finally, the buffer layer annealing and post annealing treatment could efficiently improve the properties of hydrothermally grown ZnO nanorods. The morphology and structural properties of ZnO nanorods grown by the hydrothermal synthesis were measured by atomic force microscopy (AFM), field emission scanning electron microscopy (SEM), and x-ray diffraction (XRD). The optical properties were also analyzed by photoluminescence (PL) measurement.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.16.1-16.1
• /
• 2009

We have fabricated solution processed oxide semiconductor active layer for thin film transistors (TFTs). The oxide semiconductor layers were prepared by ink-jet printing the sol-gel precursor solution based on doped-ZnO. Inorganic ZnO-based thin films have drawn significant attention as an active channel layer for TFTs applications alternative to conventional Si-based materials and organic semiconducting materials, due to their wide energy band gap, optical transparency, high mobility, and better stability. However, in spite of such excellent device performances, the fabrication methods of ZnO related oxide active layer involve high cost vacuum processes such as sputtering and pulsed laser deposition. Herein we introduced the ink-jet printing technology to prepare the active layers of oxide semiconductor. Stable sol-gel precursor solutions were obtained by controlling the composition of precursor as well as solvents and stabilizers, and their influences on electrical performance of the transistors were demonstrated by measuring electrical parameters such as off-current, on-current, mobility, and threshold voltage. Microstructure and thermal behavior of the doped ZnO films were investigated by SEM, XRD, and TG/DTA. Furthermore, we studied the influence of the ink-jet printing conditions such as substrate temperature and surface treatment on the microstructure of the ink-jet printed active layers and electrical performance. The mobility value of the device with optimized condition was about 0.1-1.0 $cm^2/Vs$ and the on/off current ratio was about $10^6$. Our investigations demonstrate the feasibility of the ink-jet printed oxide TFTs toward successful application to cost-effective and mass-producible displays.

• 한국산학기술학회논문지
• /
• 제16권2호
• /
• pp.1555-1562
• /
• 2015

금속 산화물 반도체는 독특한 전기 광학적 특성, 높은 표면적 등으로 인해 태양전지, 센서, 광소자 및 디스플레이 등 여러 분야에 걸쳐 응용되고 있다. 금속 산화물 가운데 우수한 물리 화학적 특성을 가지는 산화아연은 3.37 eV의 넓은 밴드갭 에너지와 60 meV의 큰 엑시톤 결합에너지를 갖는 n-형 반도체로서 산화아연에 양이온을 도핑하여 전기 광학적 특성을 보완하는 연구가 진행되고 있다. 본 연구는 알루미늄이 도핑 된 산화아연을 마이크로파 수열합성법으로 합성하였다. 전구체의 종류와 몰 비 등의 반응 변수를 조절하여 최적의 결정형상과 광학적 특성을 갖는 산화아연을 합성하였으며, 알루미늄을 도핑하여 광학적 특성 변화를 시도하였다. 합성된 입자는 SEM, XRD, PL, UV-Vis 분광기 및 EDS 등의 기기분석을 통해 광학적, 물리 화학적 특성을 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.48-48
• /
• 2007

P-type transparent conducting $CuGaO_2$ thin films have been prepared by DC/RF sputtering using Quartz(0001) and sapphire(0001) substrates. The target was fabricated by heating a stoichiometric mixture of CuO and $Ga_2O_3$ at 1373K for 12h under $N_2$ atmosphere. The film were deposited under mixture gas of Ar and $O_2(Ar:O_2=4:1)$ during 10~30min. and the as-deposited films were annealed at 1123K and $N_2$ atmosphere. Room temperature conductivity and the activation energy of the sintered body in the temperature range of 223K ~ 423K were 0 004S/cm, 1.9eV, respectively. XRD revealed that all of the as-deposited films were amorphous. Heating of the films deposited on Quartz substrates above 1123K resulted in crystallization with a second phase of $CuSiO_3$, which was assumed owing to reaction with Quartz substrate. The single phase of $CuGaO_2$ was obtained at the film deposited on the sapphire substrates. The transmittance after annealing of DC- and RF-sputtered films were 55~75% at 550nm. From the transmittance and reflectance measurement. the direct band gap of the DC/RF-sputtered films were 3.63eV and 3.57eV. and there was little difference between DC and RF sputtered films.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.101-101
• /
• 2010

ZnO shows a direct band gap of 3.37eV, large exciton binding energy (~60 meV), high oxidation ability, high sensitivity to many gases, and low cost, and it has been used in various applications such as transparent electrodes, light emitting diodes (LEDs), gas sensors and photocatalysts. Among these applications ZnO as photocatalyst has considerably attracted attention over the past few years because of its high activities in removing organic contaminants generated from industrial activities. In this research, ZnO nanoparticles were synthesized by spray-pyrolysis method using the zinc acetate dihydrate as starting material at synthesis temperature of $900^{\circ}C$ with concentration varied from 0.01 to 1.0M. The physical and chemical properties of the synthesized ZnO nanoparticles were examined by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Fourier Transformation Infrared (FT-IR), and UV-vis spectroscopy. The Miller indices of XRD patterns indicate that the synthesized ZnO nanoparticles showed a hexagonal wurtzite structure. With increased precursor concentration, a primary, secondary particle sizes of ZnO nanoparticles increased by 0.8 to $1.5{\mu}m$ and 15 to 35nm, and their crystallinity was improved. Methyleneblue (MB) solution ($1{\mu}M$) as a test comtaminant was prepared for evaluating the photocatalytic activities of ZnO nanoparticles synthesized in different precursor concentration. The results show that the photocatalytic efficiency of ZnO nanoparticles was gradually enhanced by increased precursor concentration.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.124-124
• /
• 2010

Much interest has been focused on InGaN-based materials and their quantum structures due to their optoelectronics applications such as light emitting diode (LED) and photovoltaic devices, because of its high thermal conductivity, high optical efficiency, and direct wide band gap, in spite of their high density of threading dislocations. Build-in internal field-induced quantum-confined Stark effect in InGaN/GaN quantum well LED structures results in a spatial separation of electrons and holes, which leads to a reduction of radiative recombination rate. Therefore, many growth techniques have been developed by utilizing lateral over-growth mode or by inserting additional layers such as patterned layer and superlattices for reducing threading dislocations and internal fields. In this work, we investigated various characteristics of InGaN multiple quantum wells (MQWs) LED structures grown on selectively wet-etched porous (SWEP) GaN template layer and compared with those grown on non-porous GaN template layer over c-plane sapphire substrates. From the surface morphology measured by atomic force microscope, high resolution X-ray diffraction analysis, low temperature photoluminescence (PL) and PL excitation measurements, good structural and optical properties were observed on both LED structures. However, InGaN MQWs LED structures grown on SWEP GaN template layer show relatively low In composition, thin well width, and blue shift of PL spectra on MQW emission. These results were explained by rough surface of template layer, reduction of residual compressive stress, and less piezoelectric field on MQWs by utilizing SWEP GaN template layer. Better electrical properties were also observed for InGaN MQWs on SWEP GaN template layer, specially at reverse operating condition for I-V measurements.

• 한국표면공학회지
• /
• 제55권2호
• /
• pp.91-95
• /
• 2022

ZnO single layer (60 nm thick) and ZnO with Ag interlayer (ZnO/Ag/ZnO; ZAZ) films were deposited on the glass substrates by using radio frequency (RF) and direct current (DC) magnetron sputter to evaluate the effectiveness of Ag interlayer on the optical visible transmittance and the conductivity of the films. In the ZAZ films, the thickness of ZnO layers was kept at 30 nm, while the Ag thickness was varied as 5, 10, 15 and 20 nm. In X-ray diffraction (XRD) analysis, ZnO films show the (002) diffraction peak and ZAZ films also show the weak ZnO (002) peak and Ag (111) diffraction peak. As a thickness of Ag interlayer increased to 20 nm, the grain size of the Ag films enlarged to 11.42 nm and the optical band gap also increased from 4.15 to 4.22 eV with carrier concentration increasing from 4.9 to 10.5×10²¹ cm^-3. In figure of merit measurements, the ZAZ films with a 10 nm thick Ag interlayer showed the higher figure of merit of 4.0×10^-3 Ω^-1 than the ZnO single layer and another ZAZ films. From the experimental result, it is assumed that the Ag interlayer enhanced effectively the opto-electrical performance of the ZAZ films.

• 반도체디스플레이기술학회지
• /
• 제21권2호
• /
• pp.101-106
• /
• 2022

In this paper, WBG semiconductor such as SiC and GaN were applied as power switches for LCL circuit that can be applied to satellite power systems and the test results of the LCL circuit are reported. P-channel MOSFET and N-channel MOSFET, which were generally used in the conventional LCL circuit, were applied together to expand the utility of the test results. The design and stability evaluation were performed using a Micro Cap circuit simulation program. For the test circuit, a module using each switch was manufactured, and a total of 5 modules were manufactured and the steady state and transient state characteristics were compared. From the experimental results, the LCL circuit for power supply of the satellite power system constructed in this paper satisfied the constant current and constant voltage conditions under various operating conditions. The P-channel MOSFET showed the lowest efficiency characteristics, and the three N-channel switches of Si, SiC and GaN showed relatively high efficiency characteristics of up to 99.05% or more. In conclusion, it was verified that the on-resistor of the switch had a direct effect on the efficiency and loss characteristics.