• Journal of the Korean Applied Science and Technology
• /
• v.36 no.1
• /
• pp.333-340
• /
• 2019

This paper was described about the preparation of the multi-functional mask pack and its evaluation. Here, the multi-functional effects means the far-infrared emissivity effect due to polyphosphoric acid, the freckles treatment effect and peeling effects due to inclusion complexes, and the skin temperature decreasing effect due to Lavender-extraction compounds. The the hazardous chemicals, viscosity, and pH were determined blow 0.01%, 280 cP, and pH=6.92 in the prepared multi-functional mask pack solution, respectively. The multi-functional mask pack prepared with dipping method in the solution were showed the value of $0.882{\mu}m$ (Far-infrared emissivity) and $3.40{\times}10^2W/m$ at $37^{\circ}C$ (Far-infrared radiation energy), respectively. After taking multi-functional mask pack, the skin moisturizing rate was indicated 35.5%, and the skin temperature was showed in the range of $24{\sim}26^{\circ}C$. The skin stimulation test for the 30 volunteer was showed very strong stability.

• Journal of Navigation and Port Research
• /
• v.46 no.4
• /
• pp.297-302
• /
• 2022

An exothermic oil absorbent sheet with calcium chloride crystals can be fabricated, by dipping a clean polypropylene fabric in calcium carbonate and hydrochloric acid solution and drying it. The exothermic oil absorbent sheet applied to the seawater surface, releases heat by the dissociation of calcium chloride. The dissociation heat liquefies the solidified low-sulfur fuel oil at a low temperature, and converts it to a state at which it can be absorbed. The optimum mole concentrations of calcium carbonate and hydrochloric acid required for the exothermic oil absorbent sheet, are 0.25 M and 0.5 M, respectively. The oil absorption capacity of the exothermic oil absorbent sheet for low sulfur fuel oil depends on the seawater temperature. But, it is highly excellent at 4.5-7.08 g/g at 10℃, the average seawater temperature during the winter in Korea. The exothermic oil absorbent sheet is an excellent alternative in absorbing low-sulfur fuel oil in winter and removing it from seawater.

• Journal of the Korean Society of Tobacco Science
• /
• v.30 no.1
• /
• pp.1-7
• /
• 2008

Bacterial wilt caused by Ralstonia solanacearum has become a severe problem on tobacco in Korea. No effective single control measure is available at present time. One of the most potential way for controlling the bacterial wilt on tobacco is growing tobacco cultivars resistant to the bacterial wilt. In this study, optimal conditions for screening tobacco cultivars resistant to the bacterial wilt were examined to provide reproducible and efficient methods in growth chamber testing and field experiments for evaluating plant disease resistance. For this, already-known inoculation methods, inoculum densities, and incubation temperature, and plant growth stages at the time of inoculation were compared using tobacco cultivars resistant (Nicotiana tabacum cv, NC95), moderately resistant (N. tabacum cv. SPG70), and susceptible (N. tabacum BY4) to the bacterial disease. It was determined that root-dipping of tobacco seedlings at six true leaf stage into the bacterial suspension with inoculum level of $10^8$ colony-forming units (CFU)/ml for 20 min before transplanting was simple and most efficient in testing for resistance to the bacterial wilt of tobacco caused by R. solanacearum, for which disease incidences and severities were examined at 2 weeks of plant growth after inoculation at $20{\sim}25^{\circ}C$ in a growth chamber. These experimental conditions could discriminate one tobacco cultivar from the others by disease severity better than any other experimental conditions. In field testing, the optimum time for examining the disease occurrence was late June through early July. These results can be applied to establishing a technical manual for the screening of resistant tobacco cultivars against the bacterial wilt caused by R. solanacearum.

• Membrane Journal
• /
• v.18 no.2
• /
• pp.176-184
• /
• 2008

Nano-porous ceramic membranes was synthesized by the sol-gel method. Gas permeation of hydrogen and nitrogen was determined by single composition gas. Pore size $0.1{\mu}m$ and porosity 32% of flat type ${\alpha}-Al_2O_3$ substrate was manufactured. An intermediate ${\gamma}-Al_2O_3$ layer with pore size of 4 nm was formed by dip-coating. Polymeric silica sol was synthesized by acid catalyzed hydrolysis and condensation of tetra-ethyl-ortho-silicate. Supported membranes on alumina were prepared by dipping and calcining. He, $N_2$ permeation experiments with nanoporous sol-gel modified supported ceramic membranes were peformed to determine the gas transport characteristics. $He/N_2$ permselectivity around $100{\sim}160$ and helium permeation in the order of $10^{-7}mol/m^2{\cdot}s{\cdot}Pa$ were measured in the temperature range of $303{\sim}363K$.

• Journal of fish pathology
• /
• v.14 no.1
• /
• pp.16-20
• /
• 2001

The pathogenicity of the extracted WSBV from the hepatopancreas, the lymphoid organ, the stomach and the heart of infected shrimps was examined after artificial infection in shrimps(Penaeus chinensis). In terms of the infection route, the strength of the pathogenicity of WSBV was in the order of intramuscular, oral and dipping method. The influence of rearing water temperature on the pathogenicity of WSBV was the strongest in the order of $30^{\circ}C$, $25^{\circ}C$, $20^{\circ}C$, and $15^{\circ}C$. The isolated WSBV from the diseased shrimps showed very high pathogenicity regardless of their sizes, even though there was difference in time to reach 100% mortality. Degenerated cells characterized by hypertrophied nuclei were found in various tissues such as the lymphoid organ, the hematopoietic tissue and the epidermis in the stomach.

• Journal of Environmental Health Sciences
• /
• v.33 no.4
• /
• pp.325-337
• /
• 2007

The effect of seawater and air pollutants on the three-story stone pagodas on Gameunsa Temple Site have been studied in order to establish conservation basic plan. Also, an experimental study has been conducted to evaluate the effect of seawater salt and air pollutants on the weathering of granite. The results could be summarized as follows. Because the three-story stone pagodas on Gameunsa Temple Site are located outdoors, the external appearance has been largely deteriorated due to natural and artificial factors such as typhoon, wind, microorganisms, moisture, extreme change in temperature, air pollutants, and seawater, etc. When G.J fresh granite was dipped into the seawater, dissolution rate of three minerals (Mg, Ca, and K) are increased linearly until about 40 days and then increased abruptly. After seawater dipping experiments, the mineral compositions of the granite surface were lower then that of the G.J fresh granite but Poisson's ratio and absorption ratio were slightly increased. Therefore, from these results we can say that stone cultural properties could be weathered by seawater and air pollutants and it's considered being a meaningful experiment to study the conservation method of stone cultural properties from seawater.

• KSTLE International Journal
• /
• v.6 no.1
• /
• pp.13-16
• /
• 2005

Friction characteristics at nano-scale of self-assembled monolayers (SAMs) having different chain lengths and end groups were experimentally studied.51 order to understand the effect of the chain length and end group on the nano-scalefriction: (1) two different SAMs of shorter chain lengths with different end groups such as methyl and phenyl groups, and (2)four different kinds of SAMs having long chain lengths (C10) with end groups of fluorine and hydrogen were coated on siliconwafer (100) by dipping method and Chemical Vapour Deposition (CVD) technique. Their nano-scale friction was measuredusing an Atomic Force Microscopy (AFM) in the range of 0-40 nN normal loads. Measurements were conducted at the scanning speed of 2 $mu$m/s for the scan size of 1$mu$m x 1 $mu$m using a contact mode type $Si_3N_4$ tip (NPS 20) that had a nominal spring constant0.58 N/m. All experiments were conducted at anlbient temperature (24 $pm$1$circ$C) and relative humidity (45 $pm$ 5%). Results showedthat the friction force increased with applied normal load for all samples, and that the silicon wafer exhibited highest frictionwhen compared to SAMs. While friction was affected by the inherent adhesion in silicon wafer, it was influenced by the chainlength and end group in the SAMs. It was observed that the nano-friction decreased with the chain length in SAMs. In the caseof monolayers with shorter length, the one with the phenyl group exhibited higher friction owing to the presence of benBenerings that are stiffer in nature. In the case of SAMs with longer chain length, those with fluorine showed friction values relativelyhigher than those of hydrogen. The increase in friction due to the presence of fluorine group has been discussed with respect tothe siBe of the fluorine atom.

• Korean Journal of Materials Research
• /
• v.20 no.9
• /
• pp.451-456
• /
• 2010

A promising candidate material for a $H_2$ permeable membrane is SiC due to its many unique properties. A hydrogen-selective SiC membrane was successfully fabricated on the outer surface of an intermediate multilayer $\gamma-Al_2O_3$ with a graded structure. The $\gamma-Al_2O_3$ multilayer was formed on top of a macroporous $\alpha-Al_2O_3$ support by consecutively dipping into a set of successive solutions containing boehmite sols of different particle sizes and then calcining. The boehmite sols were prepared from an aluminum isopropoxide precursor and heated to $80^{\circ}C$ with high speed stirring for 24 hrs to hydrolyze the precursor. Then the solutions were refluxed at $92^{\circ}C$ for 20 hrs to form a boehmite precipitate. The particle size of the boehmite sols was controlled according to various experimental parameters, such as acid types and acid concentrations. The topmost SiC layer was formed on top of the intermediate $\gamma-Al_2O_3$ by pyrolysis of a SiC precursor, polycarbosilane, in an Ar atmosphere. The resulting amorphous SiC-on-$Al_2O_3$ composite membrane pyrolyzed at $900^{\circ}C$ possessed a high $H_2$ permeability of $3.61\times10^{-7}$ $mol{\cdot}m^{-2}{\cdot}s^{-1}{\cdot}Pa^{-1}$ and the $H_2/CO_2$ selectivity was much higher than the theoretical value of 4.69 in all permeation temperature ranges. Gas permeabilities through a SiC membrane are affected by Knudsen diffusion and a surface diffusion mechanism, which are based on the molecular weight of gas species and movement of adsorbed gas molecules on the surface of the pores.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.1 no.2
• /
• pp.135-137
• /
• 1968

Bathythermograph (B. T) has been coumonly used to obtain a records of water temperature in the depth of 270m from the surface. We have, however, experienced some difficulties in obtaining smoked or coated glass which is used for the bathythermograph in this region, Therefore I introduce a easy method of preparing the smoked-glass slide. Preparing method is as follows. 1. Glass slides must be cleaned by dipping into the concentrated solution of sodium hydroxide ana hydrochloric acid then rinsing with hot water and polishing with a clean gauge. 2. The cleaned slide is immersed in the wax solution for coating, and dried on the filter paper. The Wax solution is prepared as follow : 1g of white wax is dissolved in 200CC of benzol or 1g of lard is dissolved in 300CC of gasoline. 3. A slide held in a fingertip is smoked on the flame of alcohol lamp, or Meter burner. When alcohol lamp is used the fuel alcohol must contain 1/5 of benzol, and when Meker burner is used, the air intake must be blocked up. The smoking on the glass slide should be light and uniform, after smoking the slide is cooled down. 4. The smoked glass slide is again dipped into the wax solution using a fingertip and the excessive wax solution on the slide is absorbed on the filter paper and drain off. 5. Thus prepared smoked slide can be used for B.T.

• Food Science and Preservation
• /
• v.13 no.2
• /
• pp.168-173
• /
• 2006

To investigate the effect of grapefruit seed extract pretreatment and packaging materials on the quality of dried persimmon, dried persimmons were stored for $60{\sim}100$ days at room temperature $(15^{\circ}C)$ after dipping in grapefruit seed extract and then packing with LDPE (low density polyethylene) film and Nylon/LDPE film pouch $(30{\times}30cm^2)$. Weight loss of dried persimmon packaged with Nylon/LDPE film was not exceeded 86% of control. 60% mold occurrence and 50% browness were observed compared to control. There were no significant differences in the firmness, soluble solid content and color between grapefruit seed extract pretreatment and control. Grapefruit seed extracts pretreatment had an effect on the inhibition of color change in Hunters value.