• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.68-70
• /
• 2005

$SiO_2$ thin films are fabricated using sol-gel method and dipping method. Relative dielectric constant of thin films decreases a little according to increasing the measuring frequency. Tan ${\delta}$ of thin films increases a little below 100kHz and it increases rapidly over 100kHz.

• Journal of the Korean Society of Tobacco Science
• /
• v.24 no.1
• /
• pp.27-31
• /
• 2002

Three kinds of inoculation methods, capillary, root cutting and dipping were compared for an efficient way to screening the resistant tobacco variety against bacterial wilt, Ralstonia solanacearum. The pricking a capillary tube contained the pathogenic bacterial suspension(10$^{7}$ cfu/$m\ell$) to an axillary bud of each tobacco plant showed different resistance well between varieties. The less period was required in inoculating work and in disease development for the inoculation method used with capillary tube than for two other inoculation methods tested also.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.2
• /
• pp.63-67
• /
• 2011

We investigated effects of bonding conditions on the peel strength of rigid printed circuit board (RPCB)/ flexible printed circuit board (FPCB) joints bonded using a thermo-compression bond method, The electrodes on the FPCB were coated with Sn by a dipping process. We confirmed that the bonding temperature and bonding time strongly affected the bonding configuration and strength of the joints. Also, the peel strength is affected by dipping conditions; the optimum dipping condition was found to be temperature of $270^{\circ}C$ and time of 1s. The bonding strength linearly increased with increasing bonding temperature and time until $280^{\circ}C$ and 10s. The fracture energy calculated from the F-x (Forcedisplacement) curve during a peel test was the highest at bonding temperature of $280^{\circ}C$.

• Research in Plant Disease
• /
• v.16 no.2
• /
• pp.148-152
• /
• 2010

To establish the efficient screening method for resistance of radish to F. oxysporum f. sp. raphani, we investigated the development of Fusarium wilt of two radish cultivars, 'Songbaek' (susceptible) and 'Tokwang' (moderately resistant), according to several conditions such as inoculation methods, inoculum concentrations, and dipping periods of radish roots in spore suspension. By infected soil and soil-drenching inoculation methods, Fusarium wilt did not occur on the seedlings of both cultivars. In root dipping inoculation method using cut or non-cut roots of radish plants, the cut roots were easily infected by the pathogen than non-cut roots. And the disease development of two cultivars represented significant difference in non-cut root method. On the other hand, disease severity of Fusarium wilt on radish seedlings according to inoculum concentration increased in a dose-dependant manner, regardless of dipping periods. Using screening method established from the results, the 41 commercial radish cultivars were evaluated the degree of resistance to F. oxysporum f. sp. raphani. Among them, 6 radish cultivars were resistant, 22 cultivars were moderately resistant, and 13 cultivars were susceptible to Fusarium wilt.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.87-89
• /
• 2003

YBa$_2$Cu$_3$$O_{7-x}$ thin films were fabricated by MOD-TFA process via dipping method on LaAlO$_3$(LAO) single crystalline substrates. In this study, we investigated effect of solvent on the microstructure and crystallinity of YBCO thin films. The YBCO films derived from solvent with low boiling point has good surface morphologies.s.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.79-81
• /
• 2004

$TiO_2-SnO_2$ thin films are fabricated using sol-gel method. The thickness of thin films increase about $0.03{\sim}0.04{\mu}m$ every a dipping. The permittivity and dissipation factor of $TiO_2-SnO_2$ thin films decrease with increasing frequency. Thin films show semiconductive characteristics above $400^{\circ}C$.

• Tribology and Lubricants
• /
• v.24 no.2
• /
• pp.63-71
• /
• 2008

Friction and adhesion tests were conducted to investigate tribological characteristics of materials for MEMS/NEMS using atomic force microscope (AFM). AFM Si tips were chemically modified with a self-assembled monolayer (SAM) derived from trichlorosilane like octadecyltrichlorosilane (OTS) and (1H, 1H, 2H, 2H-perfluorooctyl) trichlorosilane (FOTS), and various materials, such as Si, Al, Au, Cu, Ti and PMMA films, were prepared for the tests. SAMs were coated on Si wafer by dipping method prior to AFM tip to determine a proper dipping time. The proper dipping time was determined from the measurements of contact angle, surface energy and thickness of the SAMs. AFM tips were then coated with SAMs by using the same coating condition. Friction and adhesion forces between the AFM Si tip modified with SAM and MEMS/NEMS materials were measured. These forces were compared to those when AFM tip was uncoated. According to the results, after coating OTS and FOTS, the friction and adhesion forces on all materials used in the tests decreased; however, the effect of SAM on the reduction of friction and adhesion forces could be changed according to counterpart materials. OTS was the most effective to reduce the friction and adhesion forces when counterpart material was Cu film. In case of FOTS, friction and adhesion forces decreased the most effectively on Au films.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.17 no.1
• /
• pp.133-144
• /
• 2015

A study was conducted to examine treatment method, proper concentration, and treatment time of gibberellin(GA₃) for human labor saving at harvest in 'Campbell Early' grapevine. Fruit berry thinning reduced labor by GA₃ 40ppm treatment of 5 days prior to full bloom, and, at GA₃ 10, 20, and 40ppm during full bloom, by 14.27~19.15 minutes/tree. Therefore, although labor was reduced by dipping treatment at 40ppm of 5 days prior to full bloom and 20 and 40 ppm during full bloom, severe shattering was observed at 40ppm dipping treatment, and soluble solids decreased, which suggests difficulty with commercialization. The result suggests that proper time and concentration of GA₃ fruit cluster dipping treatment at full bloom and 10 and 20ppm, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.2
• /
• pp.82-86
• /
• 2011

Lightweight aggregate which is composed of sintered polycrystalline materials usually has a certain portion of pores inside of it. Because of such a structural characteristics, it tends to that movement of water in aggregate shows an abnormal behavior against the change of outside environment. In general, water movement behavior is controlled by porosity, distribution of pore size; however, dense surface layer will also affect water movement behavior in case of artificially sintered aggregates. Factors affecting water movement behavior in the aggregate are pore distribution, pore shape, pre-wetting method, etc. In this study, absorption characteristics of aggregate under the pressure and absorption rate according to water dipping time are analyzed for the basis of pressure pumping of lightweight concrete. Two kinds of aggregates were used for the test: one is made by 'L' company in Germany and the other is of our own made at the pilot plant in Kyonggi University. Absorption rate of aggregate is measured according to water dipping time, vacuum pressure, and quenching condition. Absorption rate of aggregate with $300^{\circ}C$ quenching is higher than that of aggregate with 24 hr water dipping. Generally the more vacuum the higher water absorption rate. Water absorption rate of 'L' aggregate under -300 mmHg is 54 % higher than that of aggregate with 24 hr water dipping; however, only 2 % increase in water absorption was measured for the K622 and K73 which were of our own.

• Journal of fish pathology
• /
• v.20 no.2
• /
• pp.139-145
• /
• 2007

To decrease stress in eel (Anguilla japonica) during its culture or transportation, aspirin (ASA) known as analgesic, antiinflammatory and antithrombic agent was administrated by dipping or oral routes. Concentrations of aspirin (ASA) and salicylic acid (SA) in eel plasma were simultaneously measured by a high performance liquid chromatography (HPLC). The plasma was acidified with 0.2 M HCl and 0.2 M orthophosphoric acid, and mixed with acetonitrile. ASA and SA extracted with acetonitrile were analyzed by the HPLC equipped with reversed phase Novapak C18 column (4 ㎛ silica, 150×4 mm) and UV detector(237 nm). The mobile phase consisted of 740 ㎖ water, 900 ㎕ orthophosphoric acid (85%) and 180 ㎖ acetonitrile. The retention times of ASA, SA and 2-methylbenzoic acid(MBA) were 4.8 min, 8.4 min and 11.5 min, respectively. The limit of quantification was 0.01 ㎍/㎖ for SA and 0.05 ㎍/㎖ for ASA. The mean recovery from eel plasma was 70.8～99.6% for ASA and 95.2～100.3% for SA. This HPLC method was applied to analyze ASA and SA of eel plasma after either dipping in a concentration of 20 ppm or feeding the feed supplemented with 50 ㎎/kg BW. Only SA was detected in eel plasma after the administration of ASA by dipping or oral routes because the drug was quickly decomposed into SA in eel plasma. The amount of SA in eel plasma reached the highest value at 3hr in dipping and 7 days in oral administration. When the ASA-administrated eel were kept in ASA free aquaria, 0.02-0.03 ㎍/㎖ of SA were detected 48 hr after the administration in both routes.