• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.1
• /
• pp.81-94
• /
• 1988

A series of experiments was performed in this study to investigate the boiling heat flux between an impinging water jet and a hot surface. Test variables were surface roughness, jet velocity, saturation temperature excess of surface, nozzle diameter and the gap distance between nozzle plate and the hot surface. In order to make the impinged cooling water a forced flow streaming a long the hot surface immediately after the initial impingement, the flat nozzle tip was extended to a circular flat plate having the same diameter as the hot surface. Utilizing the dimensionless parameter study on continuity, momentum and energy equations, 5 groups of variables involved in the nucleate boiling heat transfer were derived so that it is possible to estimate the increased heat flux by impinging water jet in a similar experimental work. For the case of saturated water being impinging onto a high temperature surface, an applicable correlation among dimensionless parameters describing the heat flux was found to be as follow.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.2
• /
• pp.19-26
• /
• 2013

Stress triaxiality is recognized as one of the most important factors for predicting the failure strain of ductile metals. This study dealt with the effect of the average stress triaxiality on the failure strain of a typical low-temperature high-strength marine structural steel, EH36. Tensile tests were carried out on flat specimens with different notches, from relatively smooth to very sharp levels. Numerical simulations of each specimen were performed by using ABAQUS. The failure initiation points in numerical simulations were identified from a comparison of the engineering stress vs. strain curves obtained from experiments with simulated ones. The failure strain curves for various dimensionless critical energy levels were established in the average stress triaxiality domain and compared with the identified failure strain points. It was observed that most of the failure initiation points were approximated with a 100% dimensionless critical energy curve. It was concluded that the failure strains were well expressed as a function of the average stress triaxiality.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.9
• /
• pp.720-727
• /
• 2008

Time delay effects on near-wall turbulent structures are investigated by performing a large-eddy simulation of a transient turbulent flow in a pipe. To elucidate the time delay effects on the near-wall turbulence, we selected the dimensionless acceleration parameter which was used in the previous study. Various turbulent statistics revealed the distinctive features of the delay. It was shown that the dynamic Smagorinsky model is valid to capture the alterations of the turbulence physics well. A dimensionless time for the responses of the flow quantities was introduced to give the detailed information on the delay of the nearwall turbulence. The conditionally-averaged flow fields associated with Reynolds shear stress producing events show that sweep and ejections are closely related to the delays of the turbulence production and the turbulence propagation toward the pipe center. The present study suggested that the enhanced anisotropy of the turbulence in the initial and transient stages would be a challenging problem to standard turbulence models.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.4
• /
• pp.633-641
• /
• 1995

The effect of the gap width on conjugate heat transfer in the cylindrical annulus for an insulated tube has been studied numerically by the finite difference method. The parameters considered here are the Rayleigh number, Ra, the dimensionless insulated wall thickness, $W/D_i$ and the dimensionless gap width, S/W. As S/W increases, the mean wall temperature increases at the inside wall of annulus and decreases at the outside walls of annulus and the insulated tube at $S/W{\leq}0.5$, and then slightly increases at $Re=10^4$, $W/D_i=1.47$. The heat transfer rate decreases at $S/W{\leq}0.5$ and then increases apparently as S/W increases at $Re=10^4$, W/Df=1.47. Therefore, it is considered that $$S/W{\sim_=}0.5$$ is the optimum gap width for the effect of insulation at $Re=10^4$, $W/D_f=1.47$.

• Structural Engineering and Mechanics
• /
• v.55 no.5
• /
• pp.1001-1014
• /
• 2015

Bending analysis of functionally graded (FG) nano-plates is investigated in the present work based on a new sinusoidal shear deformation theory. The theory accounts for sinusoidal distribution of transverse shear stress, and satisfies the free transverse shear stress conditions on the top and bottom surfaces of the plate without using shear correction factor. The material properties of nano-plate are assumed to vary according to power law distribution of the volume fraction of the constituents. The size effects are considered based on Eringen's nonlocal theory. Governing equations are derived using energy method and Hamilton's principle. The closed-form solutions of simply supported nano-plates are obtained and the results are compared with those of first-order shear deformation theory and higher-order shear deformation theory. The effects of different parameters such as nano-plate length and thickness, elastic foundation, orientation of foundation orthtotropy direction and nonlocal parameters are shown in dimensionless displacement of system. It can be found that with increasing nonlocal parameter, the dimensionless displacement of nano-plate increases.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.6
• /
• pp.855-860
• /
• 1999

An experimental study of jet impingement on the surface with linear temperature gradient is conducted with the presentation of the turbulent characteristics and the heat transfer rates measured when this jet impinges normally to a flat plate. The jet Reynolds number ranges from 30,000 to 90,000, the temperature gradient of the plate is 2~$4.2^{\circ}C$/cm and the dimensionless nozzle to plate distance(H/D) is from 6 to 10. The results show that the peak of heat transfer rate occurs at the stagnation point, and the heat transfer rate decreases as the radial distance from the stagnation point increases. A remarkable feature of the heat transfer rate is the existence of the second peak. This is due to the turbulent development of the wall jet. Maximum heat transfer rate occurs when the axial distance from the nozzle to nozzle diameter(H/D) is 8. The heat transfer rate can be correlated as a power function of Prandtl number, Reynolds number and the dimensionless nozzle to plate distance(H/D). It has been found that the heat transfer rate increases with increasing turbulent intensity.

• Korean Journal of Hydrosciences
• /
• v.7
• /
• pp.21-35
• /
• 1996

This Study is to develop the suitable hydrologic models for determination of the size and location of detention storage facilities to restrain stormwater runoff in urban areas. Hypothetical areas of two levels are considered to seize the hydrologic response characteristics. A one-square-kilometer ares is selected for the catchment level, and a 10-square-kilometer area consisting of 10 catchments is adapted at the watershed level as representative of urban drainage area. In this analysis, different rainfall freqyencies, land uses, drainage patte군, basin shates and detention storage policies are considered. Folw reduction effect of detention storage facilities is deduced from storage ratio and detention basin factor. A substantial saving in detention storage volumes is achieved 노두 the detention storage is planned at the watershed level rather than the catchment level. For the application of real watersheds, two watersheds in Seoul metropolitan area-Jamshil 2 and Seongnae 1-are selected on the basis of hydrologic response charactaristics. Through the regression analysis between dimensionless deterntion storage volume, dimensionless upstream area ratio and reduction rate of storage ratio, the regression equations to determine the size and location of detention storage faclities are presented.

• Proceedings of the Korea Water Resources Association Conference
• /
• 1987.07a
• /
• pp.87-87
• /
• 1987

Bridge piers are sometimes damaged by local scour. Although the problem of local scour around pier has been studied extensively, it has been difficult to estimate local scour deth quantitatively. This study is concerned with local scour around semicylindrical piers arranged in various types under the condition of clear water scour. Through dimensional analysis, it was found that scour depths were relative to Re, Fr, and Ns. In the case of semicylindrical piers, the variation of dimensionless scour depth with dimensionless time (effect of Ns, pier diameter and length, incidence angle) and the variation of scour depth with vortex intensity and resistance are investigated experimentally to obtain a formula. And forula for estimating the maximum depth of scour is obtained.

• Water for future
• /
• v.20 no.1
• /
• pp.41-47
• /
• 1987

Bridge piers are sometimes damaged by local scour. Although the problem of local scour around pier has been studied extensively, it has been difficult to estimate local scour depth quantitatively. This study is concerned with local scour around semicylindrical piers arranged in various types under the condition of clear water scour. Through dimensional analysis, it was found that scour depths were relative to Re, Fr, and Ns. In the case of semicylindrical piers, the variation of dimensionless scour depth with dimensionless time (effect of Ns, pier diameter and length, incidence angle) and the variation of scour depth with vortex intensity and resistance are investigated experimentally to obtain a formula. And formula for estimating the maximum depth of scour is obtained.

• Structural Engineering and Mechanics
• /
• v.76 no.4
• /
• pp.551-559
• /
• 2020

On the basis of nonlocal strain gradient theory, considering the material properties of porous FGM changing with thickness and the influence of moment of inertia, the wave equation of FG nano circular plate is derived by using the first-order shear deformation plate theory, by introducing dimensionless parameters, we transform the equations into dimensionless wave equations, and the dispersion relations of bending wave, shear wave and longitudinal wave are obtained by Laplace and Hankel integral transformation method. The influence of nonlocal parameter, porosity volume fraction, strain gradient parameters and power law index on the propagation characteristics of bending wave, shear wave and longitudinal wave in FG nano circular plate.