• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.39 no.3
• /
• pp.120-126
• /
• 2013

Objectives: This study sought to elucidate the effect of autogenous tooth bone material by experimenting on minipig's maxillary sinus and performing histological and histomorphometric analyses. Materials and Methods: Five 18-24 month-old male minipigs were selected, and right maxillary sinuses were grafted with bone graft material made of their respective autogenous teeth extracted eight weeks earlier. The left sides were grafted with synthetic hydroxyapatite as control groups. All minipigs were sacrificed at 12 weeks after bone graft, which was known to be 1 sigma (${\sigma}$) period for pigs. Specimens were evaluated histologically under a light microscope after haematoxylin-eosin staining followed by semi-quantitative study via histomorphometric analysis. The ratio of new bone to total area was evaluated using digital software for calculation of area. Results: All specimens were available, except one on the right side (experimental group), which was missing during specimen preparation. This study demonstrated new bone at the periphery of the existing bone in both groups, showing evidence of bone remodeling, however, encroachment of new bone on the central part of the graft at the 1 ${\sigma}$ period was observed only in the autogenous tooth bone group (experimental group). Histomorphometric analysis showed more new bone formation in the experimental group compared to the control group. Although the difference was not statistically significant (P>0.05), the mean percentage area for new bone for the experimental and control groups were $57.19%{\pm}11.16%$ and $34.07%{\pm}13.09%$, respectively. Conclusion: The novel bone graft material using autogenous tooth is a good alternative to autogenous bone, comparable to autogenous bone, and outperforming synthetic hydroxyapatite bone graft materials in terms of bone regeneration capacity. Augmentation with autogenous tooth bone materials will reduce donor site morbidity without hampering the safety of the autogenous bone graft.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.7138-7145
• /
• 2015

In this study, experiments were conducted to investigate the correspondence between the output voltage of the photoelectric sensor and the frost height under heating and defrosting capacity test condition (dry bulb temperature $2^{\circ}C$, wet bulb temperature $1^{\circ}C$) described at KS C 9306, where a real heat exchanger was used as a test rig instead of a large-scale model. A digital microscope and a photoelectric sensor unit consisting of an emitter and a transistor (receiver) were installed in the front of it. A linear correlation is proposed to predict the frost height based on 150 experimental data, approximately 54% of the measured data are consistent with the predicted frost heights within a relative deviation of ${\pm}10%$, it yields good agreement with 90% of the measured data when the frost height larger than 0.3mm with in a relative deviation of ${\pm}10%$. Compared with Xiao's correlation, the slope namely, the change of frost height in accordance with the change of output voltage is consistent within the error of 2.3%. But vertical intercept shows big difference with Xiao's correlation, because it was developed with a large scale model instead of a real heat exchanger.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.3 no.1
• /
• pp.12-22
• /
• 2000

Recently urbanization and industrialization around the Nak-dong river watershed have lead to the regional environmental problems. In this viewpoint, we took up variables which were related to watershed environment, and found out spatial and environmental properties of the Nak-dong river using factor analysis, ANOVA test and geographic information system. The results may be summarized as follows; three common factors which were named as urban, agricultural and industrial pollutant factor extracted from statistical methods. Spatial distribution of watershed environment could be found by connection attributes of factor scores derived from factor analysis to digital map using GIS. According to the results, distribution of pollutant sources were concentrated in the main stream of the Nak-dong river and its tributaries, Kum-ho river. So it is necessary to manage the watershed environment in due consideration of environmental carrying capacity.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.11 no.4
• /
• pp.64-75
• /
• 2008

Since the current database systems for managing geotechnical investigation results were limited by being described boring test result in point feature, it has been trouble for using other GIS data. Although there are some studies for spatial characteristics of subsurface modeling, it is rather lack of being interoperable with GIS, considering geotechnical engineering facts. This is reason for difficulty of practical uses. In this study, we has developed subsurface spatial information model through extracting needed geotechnical engineering data from geotechnical information DB. The developed geotechnical information clustering program(GEOCL) has made a cluster of boring formation(and formation ratio), classification of layer, and strength characteristics of subsurface. The interpolation of boring data has been achieved through zonal kriging method in the consideration of spatial distribution of created cluster. Finally, we make a subsurface spatial information model to integrate with digital elevation model, and visualize 3-dimensional model by subsurface spatial information viewing program(SSIVIEW). We expect to strengthen application capacity of developed model in subsurface interpretation and foundation design of construction works.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.199-206
• /
• 2006

Automatic grease lubricator is equipment that provides adequate amount of fresh grease constantly to the shaft and the bearings of machines. It minimizes the friction heat and reduces the friction loss of machines to the least. This research is to develop automatic grease lubricator by gear driven mechanism with controlled operation time. The ultimate design of this equipment is to lubricate an adequate amount of grease by a simple switch clicking according to the advanced set cycle. The backlash of the gear was minimized to increase the output power. To increase the power of gear mechanism, the binding frequency and the thickness of the coil were changed. To control the rotating cycles of the main shaft according to its set numbers, different resistance and chips were used to design the circuit to controls electrical signals with pulse. The body of the lubricator was analyzed by stress analysis with different constructed angle. The stress analysis for differing loading pressures applied to the exterior body of grease lubricator due to the setup angle, was found that the maximum stress was distributed over the outlet part where the grease lubricator suddenly narrowed contracts. Digital mock-up was analyzed and the rapid prototyping(RP) trial products were tested with PCB circuit and grease. The evaluation of the outlet capacity for RP trial products was conducted, because the friction caused by the outlet on the wall surface was an important factor in the operation of the equipment. Finally, the finishing process was applied to decrease the roughness of the surface to a comparable level and was able to test the performance examination for the product.

• Journal of Biomedical Engineering Research
• /
• v.24 no.3
• /
• pp.159-165
• /
• 2003

We developed a 37-channel magnetoencephalogram (MEG) measurement system based on low-noise superconducting quantum interference device (SQUID) magnetometets, and operated the system to measure MEG signals. By using double relaxation oscillation SQUIDs with high flux-4o-voltage transfers, the SQUID outputs could be measured directly by room temperature preamplifiers and compact readout circuits were used for SQUID operation. The average field noise level of the magnetometers is about 3 fT/√Hz in the white region, low enough for MEG measurements when operated inside a magnetically shielded room. The 37 magnetometers were distributed on a hemispherical surface haying a radius of 125 mm. In addition to the 37 sensing channels. 11 reference channels were installed to pickup external noise and to form software gradiometers. A low-noise liquid helium dewar was fabricated with a liquid capacity of 30 L and boil-off rate of 4 L/d. The signal processing software consists of digital filtering, software gradiometer, isofield mapping and source localization. By using the developed system, we measured auditory-evoked fields and localized the current dipoles, demonstrating the effectiveness of the system.

• Journal of the Korean Geographical Society
• /
• v.37 no.3
• /
• pp.203-221
• /
• 2002

This study attempts to analyze the spatial characteristics of cyberspace and to map spatial variations of cyberspace. In order to analyze the spatial distribution of cyberspace, three measurement indices are selected such as commercial domain number, Internet backbone network, and Internet users, which are highly correlated to each other. The three sets of measurement showed that cyberspace in Korea is spreading in a highly uneven fashion, strongly favoring a few cities and unfavoring economically distressed cities. Seoul acts on overwhelmingly dominant role in cyberspace, by being concentrated a number of domains and having high-capacity bandwidth on Internet backbone network. Internet is selectively connecting several cities into highly interactive networks, while at the same time largely bypassing other cities. The development of Internet network through infrastructure investments at selected cities has resulted in an uneven accessibility and digital divide among cities. The regional disparity would be further reinforced by ICT development as the primary vehicle for unequal accessibility. The result of this study revealed that geography continues to matter, despite the recent rhetoric claiming of 'the death of distance'or 'the end of geography'.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.12A
• /
• pp.1172-1176
• /
• 2008

In this paper, we describe the implementation and performance of a dual-mode Software Define Radio (SDR) smart antenna base station system. SDR technology enables a communication system to be reconfigured through software downloads to the flexible hardware platform that is implemented using programmable devices such as Digital Signal Processors (DSPs), Field Programmable Gate Arrays (FPGAs), and microprocessors. The presented base station channel card comprises the physical layer (pHY) including the baseband modem as well as the beamforming module. This channel card is designed to support TDD High-Speed Downlink Packet Access (HSDPA) as well as Wireless Broadband Portable Internet (WiBro) utilizing the SDR technology. We first describe the operations and functions required in WiBro and TDD HSDPA. Then, we explain the channel card design procedure and hardware implementation. Finally, we evaluate WiBro and TDD HSDPA performance by simulation and actual channel-card-based processing. Our smart antenna base-station dual-mode channel card shows flexibility and tremendous performance gains in terms of communication capacity and cell coverage.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.12
• /
• pp.842-849
• /
• 2007

For a $CO_2$ two-stage twin rotary compressor used for heat pump water heater system, changes of $CO_2$ solubility in PAG oil were investigated along the gas passages from the first stage suction to final discharge. Only slight changes in solubility took place in suction chambers for both of the first and second stages, but for compression chambers, solubility variation ranged from 0.115 to 0.136, and from 0.133 to 0.182, respectively for the first and second stages. Calculation of gas flashing in parts of leakage oil flows and of oil contained in control volumes due to solubility changes was conducted and included in gas pressure calculation. For the second stage, gas flashing amounts to around $5%\sim6%$ for most leakage flows. Cooling capacity, compressor input, and COP obtained by calculation were well compared to the experimental results. Effects of operation speed on the compressor performance was also studied: as the shaft speed increased, adiabatic efficiency decreased rapidly due to increased over-compression loss.

• Journal of the Korea Society for Simulation
• /
• v.15 no.4
• /
• pp.143-151
• /
• 2006

This paper deals with the simulation model for design and operations of A-Mart logistic center for low temperature products. In developed simulation model, receiving docks, digital classification system (DCS), shipping docks, material handling devices and manual sorting stations are considered. Five types of cargo such as fruits, palletized fruits, delicatessen and fisheries, vegetables and refrigerated cargoes are considered. The simulation model and process animation are developed using the simulation package ARENA. Among various design and operation alternatives consisting of the number of workers of receiving dock, allocation of receiving docks by cargo types, DCS capacity, the number of folk-lift, the number of manual sorting operators and overall layout, the best alternatives of each subsystem are selected by simulation analysis. The major performance measures such as DCS throughput, utilization of operators at each station, receiving docks utilization and folk-lift utilization are considered for the alternative evaluation.