• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.30-38
• /
• 2003

High-speed machining is one of the most effective technology to enhance productivity especially for hardened die material. High-speed machining can give great advantages for machining of dies and molds. But selection of machining condition is very difficult because of complicated machining mechanism. This paper presents the selection of machining condition in high-speed machining of STD11. Depth of cut, feed rate and spindle revolution are control factors. The effect of the control factors on surface roughness and machining error in Z-direction is discussed to improve machining accuracy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.20-25
• /
• 1996

The needs to machine hardened steels with high productivity and good surface integrity have been increased in the dies ＆ molds industry. This paper presents some experimental results on the CBN ball endmilling for hardened tool steel. This investigation concerns on the effects of cutting speed and cutting fluids on the cutting performance such as cutting forces, tool wear, and surface finish. The wear of CBN ball endmill for each cutting conditions were also examined through the microscopic observation. It has been found out that the higher cutting speeds with cutting fluids result in better cutting performance.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.10
• /
• pp.157-163
• /
• 1997

The needs to machine hardened steels with high productivity and good sufrace integrity have been increased in the dies & molds industry. This paper presents some experimental results on the CBN ball endmilling for hardened tool steel. This investigation concerns on the effects of cutting fluids, cutting speed, and feed on the cutting performance such as cutting forces, tool wear, and surface finish. The wear of CBN ball endmill for each cutting conditions were also examined through the microscopic observation. It has been found that the higher cutting speeds with cutting fluids result in better cutting performance.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1182-1191
• /
• 1994

This paper presents an enhanced method of slit beam projection intended for the rapid measurement of 3-dimensional surface profiles of dies and molds. Special emphasis is given to optimizing the design of optical system so that the measuring accuracy can be maximized by adopting two-plane camera calibration together with sub-pixel image processing techniques. Finally, several measurement examples are discussed to demonstrate that an actual measuring accuracy of $\pm$ 0.2 mm can be achieved over the measuring range of 500 mm{\times}300mm{\times}200mm$.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.5
• /
• pp.1-6
• /
• 2005

Machining is a one of the broadly used manufacturing process to produce the parts, products and various molds and dies. The environmental impact due to aerosol generation via atomization process is a major concern associated with environmental consciousness. This paper presents the experimental results to analyze the characteristics of cutting fluid aerosol generation in grinding process. Experimental results show that the generated fine aerosol which particle size less than 10micron appears near worker's breath zone under given operational conditions. The aerosol concentration is much higher enough to affect human health risk with its generated aerosol quantities. This quantitative analysis can be provided the basic knowledge f3r further research for environmentally conscious machining technology developments.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.282-287
• /
• 2005

This paper presents the experimental results to analyze the characteristics of cutting fluid aerosol generation in grinding process. Machining is a one of the broad manufacturing process to produce the parts, products and various molds and dies. The environmental impact due to aerosol generation via atomization process is a major concern associated with environmental consciousness. Experimental results show that the generated fine aerosol which particle size less than 10 micron appears near worker's breath zone under given operational conditions. The aerosol concentration is much higher enough to affect human health risk with its generated aerosol quantities. This qualitative analysis can be provided the basic knowledge for further research for environmentally conscious machining technology developments.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11b
• /
• pp.937-940
• /
• 2010

본 연구는 fine blanking 프레스로부터 기능면으로 사용되는 100% clean cut 전단면을 얻는 fine blanking 공정에서 die roll을 최소화하기 위한 목적으로 성형 해석 및 실험적 방법을 통해 die chamfer 형상에 따라 성형되는 제품의 die roll size 변화를 검토한 것이다. fine blanking 과정을 묘사하기 위하여 deform 2D를 이용하여 성형 해석을 수행하여 die roll size를 예측하였으며, 실제 die chamfer가 다른 die insert를 제작하여 fine blanking 실험을 실시하여 die chamfer 형상에 따른 die roll size에 대한 해석 data와 실험 data를 비교 분석하여 die roll 길이 방향 size의 경향을 파악할 수 있었다. 이 연구 결과는 fine blanking 판재 성형에서 die roll을 최소화하기 위한 die chamfer 설계에 유용하게 적용될 것으로 판단된다.

• Design & Manufacturing
• /
• v.10 no.3
• /
• pp.8-13
• /
• 2016

Despite technological advance, there have been several troubles in photo reaction injection molding (photo RIM) to produce ultra thin light guide panels (LGPs). In this study, micro leakage problem at cavity edge during photo RIM was investigated numerically. In order to obtain optimal processing conditions, we regulated inlet pressure of injected resin at the cavity edge and figured out micro leakage behaviors. At low inlet pressure (less than 100 Pa), though the micro leakage problem was not occurred, another problem, short shot due to not enough driving force, was appeared More than 1,000 Pa of the inlet pressure, injected resin was rapidly leaked through the micro gap at the cavity edge. Finally, we obtained optimal inlet pressure around 600 ~ 1,000 Pa. At this region, injected resin fully filled the cavity without micro leakage behavior. Based on the present study, further comparative investigations with experimental photo RIM should be performed to find optimal processing conditions for produce ultra thin LGPs.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.1-8
• /
• 2017

In this study, we applied microcellular foaming injection molding process to improve the performance of system air-conditioner drain fan which had been produced by injection molding process and studied the optimization of process conditions through 6-sigma process and response surface method (RSM) to reduce weight and deformation of products. Additive type, melt temperature, mold temperature, and injection screw shape were selected as the factor affecting the weight and deformation of the products by carrying out analysis of trivial many through ANOVA and design of experiment (DOE) method. Among the effect factor, we set the addictive type to Long G/F and screw shape to foaming screw which had the highest level of weight reduction and deformation reduction. The amount of foaming agent gas was set at 60 ml, which was the limit beyond which the weight of product did not decrease any more. For melt temperature and mold temperature, we studied the conditions where both weight and deformation were minimized using the RSM. As a result, we set the melt temperature to $250^{\circ}C$, fixed mold temperature to $20^{\circ}C$, and moving mold temperature to $40^{\circ}C$. The improvement effect was analyzed by appling the selected optimal conditions to the production process using the microcellular foaming injection molding. The results showed that the mean weight of product was measured to be 1,420g which was 19% lower than that measured in the current process. The standard deviations of the weights were found to be similar to those in the current process and it showed a low dispersion. The mean deformation was measured to be 0.9237mm, which represented a 57% reduction compared to the mean deformation in the current process, and the standard deviation decreased from 0.3298mm to 0.1398mm. Moreover, we analyzed the process capability for deformation, and the results showed that the short-term process capability increased from 2.73 to 6.60 which was even higher than targeted level of 6.0.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.1
• /
• pp.9-16
• /
• 2012

Recently, an optics-based concentrator for solar concentration has been a key issue in development of photovoltaic systems. In the present study, a new, simple, easily producible planar concentrator based on a light guide system is proposed. In this device, solar light is concentrated by microprism optical patterns guiding the light, mainly through total reflection and refraction. The main design variables of the concentrator are the geometric concentration ratio ($R_c$) and the ${\Theta}_1$ and ${\Theta}_2$ of the microprism pattern. Ray tracing was simulated using commercial software, SPEOS, and the optical efficiencies of the light guide solar concentrator were predicted in each case. The predicted maximum optical efficiencies are 65.60%, 54.78%, and 46.78%, respectively, for $R_c$ values of 4, 5, and 6. The variation of the optical efficiencies according to ${\Theta}_1$, ${\Theta}_2$, and the incline angle of the incident light were predicted.