• Journal of Integrative Natural Science
• /
• v.14 no.3
• /
• pp.99-106
• /
• 2021

A mixture of alcohol and water is commonly used as antifreeze, liquor, and the fundamental solvents for the manufacture of cosmetics, pharmaceuticals, and inks in our daily life. Since various properties of alcohol water mixtures such as density, boiling or melting point, viscosity, and dielectric constant are determined by their mixing ratio, it is very important to know the mixing ratio to predict their properties. One of simple method to find the mixing ratio is measuring the density of the mixtures. However, it is not easy to predict the mixing ratio from the density of the mixtures because the relationship between mixing ratio and density has not been established well. The relationship is dependent on the relative sizes of solute and solvent molecules, and their interactions. Recently, an empirical model to predict the density of glycerol water mixture from their mixing ratio has been introduced. The suggested model is simple but quite accurate for glycerol water mixture. In this article, we investigated the applicability of this model to different alcohol water mixtures. Densities for six different alcohol water mixtures containing various alcohols (e.g., ethylene glycol, 1,3-propane diol, propylene glycol, methanol, ethanol, and 1-propanol) were simulated and compared to experimentally measured ones to investigate the applicability of the model proposed for glycerol water mixtures to other alcohol water mixtures. The model predicted the actual density of all alcohol water mixtures tested in this article with high accuracy at various ratios. This model can probably be used to predict the mixing ratio of other alcohol water mixtures from their densities beyond 6 alcohols tested in this article from their densities.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.4
• /
• pp.599-604
• /
• 2021

In the information age, internet was developed from the wired access to the wireless Internet access. When a surge in demand for wireless Internet access, efficiency and performance of 2.4 and 5GHz band which leads to saturation of the communication was significantly fall. In this paper, we studied the design and fabrication of slot patch antenna to be used in wireless communication systems operating at around 10GHz band. To obtain optimal antenna parameters such as patch size, inter patch space, sL, sW, feed L, feed w, slot patch antenna was simulated by HFSS(High Frequency Structure Simulator). From these parameters, slot and patch antenna is fabricated using FR-4 substrate of dielectric constant 4.4. The characteristics of fabricated antenna were analyzed by network analyzer. The fabricated slot patch antenna showed a center frequency as 10.23GHz, the minimum return loss as -32dB, and -10dB bandwidth as 420MHz respectively.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.38 no.2
• /
• pp.25-30
• /
• 2019

Atmospheric-pressure plasma technique is a technology for sterilizing agricultural product. In this study, dielectric barrier discharge plasma was applied to silkworm powder for 1 to 5 h with less than 2 ppm of $O_3$ and $NO_2$. Quantitative compositions including proximate contents, mineral and heavy metal contents, fatty acids, vitamins, and DNJ contents were measured. Proximate contents of silkworm powder were protein (57.2%), fat (9.9%), fiber (4.6%), ash (10.1%), and moisture (5.7%). These compositions were not affected by the treatment of plasma. Silkworm powder has 5 abundant minerals potassium (K), phosphorus (P), sulfur (S), calcium (Ca), and magnesium (Mg). Among these minerals, plasma treatment decreased the contents of P and S sharply from 732.3 to 176.8, and 492.7 to 185.2 mg/100g, respectively. Heavy metal contents including lead (Pb), cadmium (Cd), arsenic (As), and mercury (Hg) were not detected in the silkworm powder. Five vitamins such as ascorbic acid (13.6 mg/100g), riboflavin (5.4 mg/100g), ${\beta}$-carotene (1.8 mg/100g), niacin (0.6 mg/100g), and thiamine (0.4 mg/100g) were not significantly changed by plasma treatment. Silkworm powder is composed of 30 parts saturated fatty acids and 70 parts unsaturated ones. The fatty acid composition was not significantly changed by plasma treatment. The DNJ content of silkworm powder (3.72 mg/g) was also nearly constant within the experimental condition of plasma treatment.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.719-724
• /
• 2018

Cordierite composed of an alumina-silica-magnesia compound has a low coefficient of thermal expansion(CTE) and excellent thermal shock resistance. It also has a low dielectric constant and high electrical insulation. However, due to low mechanical strength, it is limited for use in a ceramic heater. In this study, $ZrO_2$ is added to an 80 wt% cordierite-20 wt% mullite composition, and the effect of $ZrO_2$ addition on the mechanical strength and thermal shock resistance is investigated. With an increasing addition of $ZrO_2$, cordierite-mullite formed $ZrO_2$, $ZrSiO_4$ and spinel phases. With sintering conducted at $1400^{\circ}C$ with the addition of 5 wt% $ZrO_2$ to 80 wt% cordierite-20 wt% mullite, the most dense microstructure forms along with an excellent mechanical strength with a 3-point flexural strength of 238MPa. When this composition is quenched in water at ${\Delta}T=400^{\circ}C$, the 3-point flexural strength is maintained. Moreover, when this composition is cooled from $800^{\circ}C$ to air, the 3-point flexural strength is maintained even after 100 cycles. In addition, the CTE is measured as $3.00{\times}10^{-6}{\cdot}K^{-1}$ at $1000^{\circ}C$. Therefore, 80 wt% cordierite-20 wt% mullite with 5 wt% $ZrO_2$ is considered to be appropriate as material for a ceramic heater.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.6
• /
• pp.1213-1222
• /
• 2018

The energy band gaps and the bowing parameters of zincblende $GaAs_{1-x}N_x$ on the variation of temperature and composition are determined by using an empirical pseudo-potential method with another virtual crystal approximation, which includes the disorder effect. The bowing parameter is calculated as 15eV and the energy band gaps are decreasing rapidly in $GaAs_{1-x}N_x$ ($0{\leq}x{\leq}0.05$, 300K). A refractive index n and a function of high-frequency dielectric constant ${\varepsilon}$ are calculated by the results of energy band gaps and the calculation results of energy band gaps are consistent with experimental values.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.475-482
• /
• 2019

In this paper, we propose a triple band antenna for GPS / DCS / WLAN system. The proposed antenna has the characteristics required by considering the interconnection of two strip lines and various slits on the ground place. The total substrate size is $31mm(W1){\times}50mm(L1)$, thickness (h) 1.6 mm, and the dielectric constant is 4.4, which is made of $22mm(W7+W12+W8){\times}43mm(L4+L3)$ antenna size on the FR-4 substrate. From the fabrication and measurement results, bandwidths of 340 MHz (1.465 to 1.805 GHz), 480 MHz (2.155 to 2.635 GHz) and 1950 MHz (4.975 to 6.925 GHz) were obtained on the basis of -10 dB. Also, gain and radiation pattern characteristics are measured and shown in the frequency triple band as required.

• Korean Journal of Materials Research
• /
• v.31 no.10
• /
• pp.539-545
• /
• 2021

The effect of Sm₂O₃ doping on the microstructure and electrical properties of the ZPCCA-based varistors is comprehensively investigated. The increase of doping content of Sm₂O₃ results in better densification (from 5.70 to 5.82 g/cm³) and smaller mean grain size (from 7.8 to 4.1 ㎛). The breakdown electric field increases significantly from 2568 to 6800 V/cm as the doping content of Sm₂O₃ increases. The doping of Sm₂O₃ remarkably improves the nonlinear properties (increasing from 23.9 to 91 in the nonlinear coefficient and decreasing from 35.2 to 0.2 µA/cm² in the leakage current density). Meanwhile, the doping of Sm₂O₃ reduces the donor concentration (the range of 2.73 × 10¹⁸ to 1.18 × 10¹⁸ cm^-3) of bulk grain and increases the barrier height (the range of 1.10 to 1.49 eV) at the grain boundary. The density of the interface states decreases in the range of of 5.31 × 10¹² to 4.08 × 10¹² cm^-2 with the increase of doping content of Sm₂O₃. The dielectric constant decreases from 1594.8 to 507.5 with the increase of doping content of Sm₂O₃.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.5
• /
• pp.877-886
• /
• 2019

The energy band gaps and optical constants of zincblende $In_yGa_{1-y}As_{1-x}N_x$ on the variation of temperature and composition are determined by using band anticrossing method. The energy band gaps are decreasing continuously in $In_yGa_{1-y}As_{1-x}N_x$ ($0{\leq}x{\leq}0.05$, $0{\leq}y{\leq}1.0$, 300K) and the bowing parameter is calculated as 0.522eV. The calculation results of energy band gaps are consistent with those of other studies. A refractive index n and a high-frequency dielectric constant ${\varepsilon}$ are calculated by a proposed modeling equation using the results of energy band gaps.

• Journal of Advanced Navigation Technology
• /
• v.25 no.3
• /
• pp.223-228
• /
• 2021

In this paper, we proposed a slot-type antenna with microstrip feed embedded in a PCB for Zigbee communication (2.4 ~ 2.484 GHz). The proposed antenna is designed on a FR-4 substrate with dielectric constant 4.3, thickness of 1.6 mm, and size of 50×65 mm². Through simulations, trends of design parameters are analyzed and optimized, and the proposed antenna composed with three slots satisfy the frequency band. The measured impedance bandwidths (|S₁₁| ≤ -10 dB) of fabricated antenna are 900 MHz (2 ~ 2.9 GHz) in Zigbee frequency band. In addition, the radiation pattern showed omnidirectional characteristics for E and H-planes, and the gain of antenna in Zigbee frequency band was 1.782 dBi.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.573-580
• /
• 2020

In this paper, the characteristics of the inductor and capacitor, which are the basic components of the circuit, are constructed in a form that can be used in the LTCC multilayer. The inductors and capacitors used for the analysis were designed with rectangular spiral structures and MIM structures inside dielectrics with a dielectric constant of 7, respectively. The measured results were extracted from each element of the equivalent circuit proposed by the curve fitting method and verified the validity of the proposed equivalent circuit based on the extracted results. The analyzed inductor and capacitor were implemented in the form of library and proved its usefulness by applying to Elliptical type 5th LPF design. The LPF was measured through practical production, and as a result, the insertion loss in the passband DC ~ 3.7 GHz was up to 1.0 dB, the return loss was 19.2 dB, and the attenuation in the rejection band was 23.9 dB, which was close to the design goal.