• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.70-73
• /
• 2002

Using zirconium ceramics makes the ferrule, which is the part of optical communications. The quality of optical communications is directly affected by the concentricity of the optic ferrule. The products of optic ferrule should be meet the following general conditions which are the outer diameter of 2.5mm and the inner diameter of 0.125mm, and high quality conditions which are the concentricity of 0.1~$0.3\mu\textrm{m}$, the form accuracy of $0.2\mu\textrm{m}$, the roundness and the cylindricity of $0.1\mu\textrm{m}$ and the surface roughness of 10nm. Generally, the diamond wheel is used for the high efficiency and precision grinding of the materials. It is good for keeping the shape as it has little wear. Because of the loading phenomena, however, it is difficult to keep the fresh surface of the wheel. In grinding process, grinding fragments resemble fine powders rather than chips. It can easily get attached to the wheel surface and thus cause a loading. The loading takes place, in which the impurities stick to the wheel surface, and the grinding characteristics of wheel is deteriorated. To prevent all of these, a suitable dressing method should be used for the wheel. In this research, the dressing system fur co-axial grinding machine was designed and produced for the machining of ferrule, which is a high performance part. The performance of the developed dressing system was evaluated by measuring the form accuracy of ferrule, which is machined by the dressed wheel in developed dressing system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.787-792
• /
• 2000

Ultra-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with Vitrified-bond CBN wheel. For various conditions of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance, the surface roughness, and the material removal are measured and discussed. The results are as follows.

• 반도체디스플레이기술학회지
• /
• 제10권3호
• /
• pp.35-42
• /
• 2011

This paper describes the characteristics of high speed grinding and the influence of wheel surface speed V and a grindability of the grinding materials. The various fine ceramics pieces was ground by metal and vitrified bonded diamond wheel. The surface roughness of fine ceramics(Zirconia($ZrO_2$), Silicon Carbide(SiC), Silicon Nitride($Si_3N_4$), Alumina($Al_2O_3$)) decreases from $0.05{\mu}m(R_{max})$ to $0.025{\mu}m(R_{max})$ when the wheel speed at grinding point increases the wheel speed. Relation between the temperature at grinding point and surface roughness was linear. Abrasive jet machining(AJM), a specialized from of shot blasting, is considered one of the most helpful micro machining methods for hard and brittle materials such as glasses and ceramics by constant pressure grinding.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.231-232
• /
• 2007

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.61-64
• /
• 1995

Grinding has been adapted as a finishing process,which can carry out form and surface integrity at the same time. Recently, high efficient and precise grinding technique is required bacause the needs for functional parts such as silicon wafer,ceramic,and electric materials are increasing. Accordingly, the development of grinding wheel appropriate to that purpose is very important. So, in this paper we newly developed a diamond grinding wheel by applying the superior characteristics of spheroidal graphite of the cast iron sintered product. Especially, a electric resistance sintering method was applied in which rapid heat treatment is possible. Finally, we have achieved successful results that the grinding wheel has high hardness,durability and grinding ability,and satisfies above conditions.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1995년도 추계학술대회 논문집
• /
• pp.76-81
• /
• 1995

MgO single crystal is widely used as a the material of high temperature resistance, but is difficult to grind because of brittleness and crack generation. Therefore, superabrasive diamond wheel is required for mirror like grinding of this material. This study describes a newly proposed optimum in-process electrolytic dressing system for carrying out effective dressing of superbrasive diamond wheel. Using this system the grinding surface of MgO single crystal was improved, the grinding force was very l9ow and crack was removed. In conclusion, this system is good to obtain the efficient grinding and mirror-like grinding without crack of MgO single crystal.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.952-955
• /
• 2002

$WC-3%(Cr_3C_2)-2%(Mo_2C)-12%Ni$ carbides were ground with three different types of electroplated diamond wheels with respect to grain friability. The grinding ratio in the case of the highest toughness grains, A becomes the highest at the workpiece speeds of 40 and 70mm/min exhibiting larger effect with smaller workpiece speed. The grinding ratio with the medium toughness grain is higher than that of grain A at higher workpiece speeds than 100mm/min. The surface roughness becomes smaller with increasing the grain friability The increasing rate on surface roughness with the increase of workpiece speed becomes higher with using the grain of lower friability.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.38-49
• /
• 1994

In this study, grindability of some representative engineering ceramics are experimentally investigated using resin bond diamond wheel with conventional surface grinding machine, and proper grinding conditions which can be obtained from various experimental results are established also for mechanical components which are proper to domestic circumstances with high reliability. And through the results of experiment, it is confirmed that grinding energies of the ceramics, especially in the case of $Al_2O_3$, are lower than steel with same machining condition in the conventional grinding because of their fine-brittle fracture mode type removal process, though the ceramics are well-known to unmachinable materials. And moreover, the total pass numbers needed for spark-out process to be completed are depend on their mechanical properties because that grinding stiffness is different from each other. The grinding force, ginding power and ground surface roughness are also measured and compared. Furthermore, the experiments carried out in this study, some useful results are obtained with can guide to grind engineering ceramics with conventional surface grinding machine.

• 한국정밀공학회지
• /
• 제19권10호
• /
• pp.195-201
• /
• 2002

This paper deals with the precision grinding for aspherical surface of optical parts. A parallel grinding method using the spherical wheel was suggested as a new grinding method. In this method, the wheel axis is positioned at a $\pi$/4 from the Z-axis in the direction of the X-axis. An advantage of this grinding method is that the wheel used in grinding achieves its maximum area, reducing wheel wear and improving the accuracy of the ground mirror surface. In addition, a truing by the CG (curve generating) method was proposed. After truing, the shape of spherical wheel transcribed on the carbon is measured by the Form-Talysurf-120L. The error of the form in the spherical wheel which is the value ${\Delta}x$ and $R{^2}{_y}$ inferred from the measured profile data is compensated by the re-truing. Finally, in the aspherical grinding experiment, the WC of the molding die was examined by the parallel grinding method using the resin bonded diamond wheel with a grain size of ＃3000. A form accuracy of 0.16${\mu}m$ P-V and a surface roughness of 0.0067${\mu}m$ Ra have been resulted.

• 한국정밀공학회지
• /
• 제16권1호통권94호
• /
• pp.18-25
• /
• 1999

Chipping is an unavoidable phenomenon in the slot grinding process of hard and brittle materials. However, it should be reduced for the improvement of surface integrity in the manufacture of optical and semiconductor components. Electrolytic In-process Dressing (ELID) technique for metal bonded superabrasive grinding wheel has been developed for mirror surface grinding of hard and brittle materials. Electrically dressed wheel surface has sharply exposed abrasives and results in lower grinding force, higher grinding efficiency in grinding. The paper deals with a newly developed method for slot grinding using ELID and was implemented to improve grooved surface quality and decreases chipping size on the edge of the groove. As a result, we accomplished chipping-free grooves and obtained the clear ground surfaces on glass and WC.