• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.23-27
• /
• 1995

In sawing operation of synthetic jewelry, the performance of diamond cutter blade is very dependent on the blade variables. This investigation presents ecperimental results which show the effects of the blade variables such as types of diamond abrasives, grain size of diamond, concentration, and bond materials on the beavior of te blades. Based on the experimental results an optimum blade condition for the sawing of cubic zirconia was recommended.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.6
• /
• pp.145-151
• /
• 1996

In sawing operation of cubic zirconia, the performance of diamond cutter blade is very dependent on the blade variables. This investigation presents experimental results which show the effects of the blade variables such as concentration, grain size of diamond, types of diamond abrasives, and bond materials on the behavior of the blades. Based on the experimental results an optimum blade condition for the sawing of cubic zirconia was recommended.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.69-74
• /
• 1995

A theoretical analysis is presented on the mechanics of diamond blade sawing. Experimental results are also presented, which show the effects of cutting variables such as cutting speed, feed speed, cutting area, and concentration of deamond blade on the cutting forces. The analytical results aggreed well with experimental ones.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.1
• /
• pp.84-90
• /
• 1996

A theoretical analysis is presented on the mechanics of diamond blade sawing. The normal and tangential components of cutting force are calculated. Experimental results are also presented, which show the effects of cutting variables such as cutting speed, feed speed, cutting area, and concentration of diamond blade on the cutting forces. The experimental results are found to be in good agreement with those predicted by the analytical calculation.

• Journal of Powder Materials
• /
• v.10 no.3
• /
• pp.201-208
• /
• 2003

Distributions of diamond particles protruding on the surface of worn diamond segments in circular saw has been investigated. Scanning electron microscope was used to examine the worn ,surface and radial saw blade wear and grinding ratio was measured. The number of protruded diamond particle was approximately 50% of the total number of particles, and that was independent of diamond particle concentration and table speed. It was also noted that the inter-particle distance did not follow a symmetric function like Gaussian distribution function, instead it fitted well with a probability density function based on gamma function. The distribution of inter-particle spacing, therefore, was analyzed using a gamma function model.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2003.10a
• /
• pp.62-63
• /
• 2003

The inter-particle distance between diamonds on the segment surface of sawing blade predicted theoretically and measured experimentally followed a Gamma or Weibull function, rather than a normal distribution function. These results suggest that random dispersion of diamond particles in the segment may not be an efficient way of improving cutting efficiency of the blade.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.11
• /
• pp.41-46
• /
• 2019

The purpose of this study is to examine and propose a high quality blade manufacturing method by applying ELID grinding technology to machining the tungsten carbide blade edge for MLCC sheet cutting. In this study, experiments are performed according to the abrasive type of grinding wheel, grinding method and grinding direction using the non-stop continuous dressing ELID grinding technology. By comparing and analyzing the chipping phenomena and surface roughness of both the blade grinding surface and the processed surface, a method for machining the tungsten carbide blade for cutting MLCC sheet is proposed. From the analysis of the surface roughness and chipping phenomena, it is confirmed that the use of diamond abrasive is advantageous for the blade machining. In addition, it succeeds in the machining of $6{\mu}m$ fine blade without any chipping, by using the grinding wheel #4000 with the diamond abrasive.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.639-643
• /
• 2002

The main purpose of this study was to investigate the formation mechanisms of imperfections such as irregular humps, outer cavity and inner cavity in the laser fusion zone of diamond saw blade. Laser beam welding was conducted to join two parts of blade; mild steel shank and Fe-Co-Ni sintered tip. The variables were beam power and travel speed. The microstructure and elements distributions of specimens were analyzed with SEM, AES, EPMA and so on. It was found that these imperfections were responded to heat input. Irregular humps were reduced in 10.4∼17.6kJ/m heat input range. However there were no clear evidences, which could explain the relations between humps formation and heat input. The number of outer cavity and inner cavity decreased as heat input was increased. Considering both possible defects formations mechanisms, it could be thought that outer cavity was caused by insufficient refill of keyhole, which was from rapid solidification of molten metal and fast molten metal flow to the rear keyhole wall at low heat input. More inner cavities were found near the interface of the fusion zone and sintered segment and in the bottom of the fusion zone. Inner cavity was mainly formed in the upper fusion zone at high heat input whereas was in the bottom at low heat input. Inner cavity was from trapping of coarsened preexist pores in the sintered tip and metal vapor due to rapid solidification of molten metal before the bubbles escaped.

• International Journal of Korean Welding Society
• /
• v.2 no.1
• /
• pp.21-24
• /
• 2002

The main purpose of this study was to investigate the formation mechanisms of imperfections such as irregular humps, outer cavity and inner cavity in the laser fusion zone of diamond saw blade. Laser beam welding was conducted to join two parts of blade; mild steel shank and Fe-Co-Ni sintered tip. The variables were beam power and travel speed. The microstructure and elements distributions of specimens were analyzed with SEM, AES, EPMA and so on. It was found that these imperfections were responded to heat input. Irregular humps were reduced in 10.4∼l7.6kJ/m heat input range. However there were no clear evidences, which could explain the relations between humps formation and heat input. The number of outer cavity and inner cavity decreased as heat input was increased. Considering both possible defects formations mechanisms, it could be thought that outer cavity was caused by insufficient refill of keyhole, which was from rapid solidification of molten metal and fast molten metal flow to the rear keyhole wall at low heat input. More inner cavities were found near the interface of the fusion zone and sintered segment and in the bottom of the fusion zone. Inner cavity was mainly formed in the upper fusion zone at high heat input whereas was in the bottom at low heat input. Inner cavity was from trapping of coarsened preexist pores in the sintered tip and metal vapor due to rapid solidification of molten metal before the bubbles escaped.

• Journal of Powder Materials
• /
• v.11 no.5
• /
• pp.412-420
• /
• 2004

The purpose of the present study is to determine an optimum composition using cheaper powders keeping with high performance of hard rock cutting diamond saw blade. With 50Fe-20(Cu . Sn)-30Co specimen, a part of Co was replaced by Ni(5%, 10%, and 15%, respectively). These specimens were hot pressed and sintered for predetermined time at various temperature. Sintering is performed by two different methods of temperature controlled method and specimen dimension controlled method. In order to determine the property of the sintered diamond saw blade, 3 point bending tester, X-ray diffractometer, and SEM were used. As the Co in the bond alloy was replaced by Ni, the hardness of the specimen increased. Thus the 50Fe-20(CuㆍSn)-15Co-15Ni specimen showed the maximum hardness of 104(HRB). The results of 3 point bending test showed that flexure strength decreased along with increase in Ni content. This is attributed to the formation of intermetallic compound(Ni$_{x}$Sn) determined by X-ray diffraction. The fracture surface after 3 point bending test showed that diamond was fractured in the specimen containing 0%, 5%, and 10%Ni, and the fracture occurred at the interface between diamond and matrix in the specimen containing 15%Ni. The cutting ability test showed that the abrasive property was not changed in the specimen containing 0%, 5%, and 10%Ni. The optimum composition determined in this study is 50Fe-20(CuㆍSn)-20Co-10Ni.