• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.62-62
• /
• 2008

As micro-system move toward higher speed and miniaturization, requirements for embedding the passive components into printed circuit boards (PCBs) grow consistently. They should be fabricated in smaller size with maintaining and even improving the overall performance. Miniaturization potential steps from the replacement of surface-mount components and the subsequent reduction of the required wiring-board real estate. Among the embedded passive components, capacitors are most widely studied because they are the major components in terms of size and number. Embedding of passive components such as capacitors into polymer-based PCB is becoming an important strategy for electronics miniaturization, device reliability, and manufacturing cost reduction Now days, the dielectric films deposited directly on the polymer substrate are also studied widely. The processing temperature below $200^{\circ}C$ is required for polymer substrates. For a low temperature deposition, bismuth-based pyrochlore materials are known as promising candidate for capacitor $B_2Mg_{2/3}Nb_{4/3}O_7$ ($B_2MN$) multi layers were deposited on Pt/$TiO_2/SiO_2$/Si substrates by radio frequency magnetron sputtering system at room temperature. The physical and structural properties of them are investigated by SEM, AFM, TEM, XPS. The dielectric properties of MIM structured capacitors were evaluated by impedance analyzer (Agilent HP4194A). The leakage current characteristics of MIM structured capacitor were measured by semiconductor parameter analysis (Agilent HP4145B). 200 nm-thick $B_2MN$ muti layer were deposited at room temperature had capacitance density about $1{\mu}F/cm^2$ at 100kHz, dissipation factor of < 1% and dielectric constant of > 100 at 100kHz.

• Korean Journal of Construction Engineering and Management
• /
• v.17 no.5
• /
• pp.78-88
• /
• 2016

Recently BIM technology has been expanded for using in construction project. However its spread has been delayed than the initial expectations, due to the high-cost of BIM infrastructure development, the lack of regulations, the lack of process and so forth. In design phase, especially, collaboration based on BIM system has being a key factor for successful next generation building project. Through the analysis of current research trend about IT technologies, virtualization and BIM service, data exchange such as drawing, 3D model, object data, properties using cloud computing and virtual server system is defined as a most successful solution. In various industrial fields, cloud computing technology is utilized as a promising solution which can reduce time and cost of hardware infrastructure. Among the cloud computing technology, VDI is receiving a great deal of attention from it market as an essential part cloud computing. VDI enables to host multiple individual virtual machines by using hypervisor. It has an advantage to easy main device management. Therefore, this study implements a step-by-step user's DaaS by analyzing the desktop resource data of the workers from Pre-design phase to Schematic design, Design develop and Construction design phase. It also develops BIM environment based on test of BIM modeler and designers in architectural design firm. The goal of the study is to enable the cloud computing BIM server. It provides cost saving, high-performance quality of working environment and cooperation's convenience and high security when doing BIM work in small and medium sized architectural design firm.

• Journal of Yeungnam Medical Science
• /
• v.19 no.2
• /
• pp.126-135
• /
• 2002

Background: Neovascular glaucoma is common secondary glaucoma at high risk for failure of glaucoma filtering surgery. Recently, trabeculectomy with adjunctive mitomycin C trabeculectomy has been tried to improve the surgical success rate of conventional trabeculectomy. But, the long-term effects of mitomycin C trabeculectomy for neovascular glaucoma are unknown. Thus, we evaluated the long-term effects of mitomycin C trabeculectomy and its prognostic factors influencing the outcome. Materials and Methods: Medical records of 62 eyes of 55 neovascular glaucoma who had undergone mitomycin C trabeculectomy were retrospectively reviewed. Surgical success was defined as intraocular pressures of 21 mmHg or less with or without glaucoma medications and no loss of light perception. Surgical failure was defined as postoperative loss of light perception in patients with preoperative vision better than light perception, additional glaucoma surgery, or phthisis bulbi in patients with preoperative vision of no light perception. Results: Postoperative success was obtained in 37 (60%) out of 62 eyes after mean followup period of $23.9{\pm}16.2$ months. Using Kaplan-Meier survival analysis, cumulative success rate at the 6-, 12-, 24- and 36-month intervals were 85%, 71%, 57% and 52%, respectively. Success rate was greater in eyes with diabetic retinopathy than other causes(p=0.005) and in eyes with preoperative panretinal photocoagulation(PRP) than without PRP(p=0.015). However, Cox proportional hazard regression analysis revealed that preoperative PRP was not a significant risk factor for surgical failure. Conclusion: Prognosis of neovascular glaucoma caused by diabetic retinopathy was better than that caused by the other disorders following mitomycin C trabeculectomy. The author would suggest that mitomycin C trabeculectomy could be effective and relatively safe as the first procedure of choice before performing glaucoma drainage device implantation or cyclodestructive procedure.

• Journal of the Korea Society of Computer and Information
• /
• v.18 no.1
• /
• pp.31-42
• /
• 2013

This research sheds light on the non-intrusive traits of mobile devices (Electronic Guidebook, Rememberer, I-Guides and eXspot) deployed in Exploratorium for enhancing visitor experience via case studies. In an interactive exhibition environment, non-intrusiveness was the key to supporting the immersive experience and meaning-making for visitors. The usability of hand-held devices directly impacted on the non-intrusiveness, thereby reshaping the form-factors of mobile devices. The change in from-factor has also minimized the functions of devices as the remember of museum experience. Furthermore, the role of mobile devices, which turned from a supposed multi-media guide to a mere rememberer, made them virtually impossible for realizing the "seamless visiting model" originally planned. An array of projects carried out in Exploration have achieved some degree of success such as increasing viewing time as well as reinforcing post-visit activities. However, taken from musicological perspective, increase in viewing time is by all means insufficient to be taken as proof since it is assumed to be achieved by photo-taking (i.e. MyExploratorium) rather than by interacting between visitors and exhibits. This issue --increased viewing time -- needs to be analyzed in depth. All in all, mobile devices used in Exploratorium can be defined as a learning tool/educational supporting medium based on personalization for (visitors') optimizing extended museum experience.

• Journal of Korean Academy of Nursing
• /
• v.47 no.6
• /
• pp.794-805
• /
• 2017

Purpose: Interface pressure is a factor that contributes to the occurrence of pressure injuries. This study aimed to investigate interface pressure at common sites of pressure injury (occipital, gluteal and peritrochanteric areas), to explore the relationships among risk factors, skin condition and interface pressure, and to identify risk factors influencing interface pressure. Methods: A total of 100 patients admitted to the intensive care unit were enrolled at a tertiary teaching hospital in Korea. Interface pressure was recorded by a scanning aid device (PalmQ). Patient data regarding age, pulmonary disease, Braden Scale score, body mass index, serum albumin, hemoglobin, mean blood pressure, body temperature, and oxygen saturation were included as risk factors. Data collected from July to September 2016 were analyzed using binary logistic regression. Results: The mean interface pressure of the occipital, gluteal, and right and left peritrochanteric areas were 37.96 (${\pm}14.90$), 41.15 (${\pm}16.04$), 53.44(${\pm}24.67$), and 54.33 (${\pm}22.80$) mmHg, respectively. Predictive factors for pressure injuries in the occipital area were age ${\geq}70$ years (OR 3.45, 95% confidence interval [CI]: 1.19~9.98), serum albumin deficit (OR 2.88, 95% CI: 1.00~8.26) and body temperature ${\geq}36.5^{\circ}C$ (OR 3.12, 95% CI: 1.17~8.17); age ${\geq}70$ years (OR 2.81, 95% CI: 1.10~7.15) in the right peritrochanteric area; and body temperature ${\geq}36.5^{\circ}C$ (OR 2.86, 95% CI: 1.17~6.98) in the left peritrochanteric area. Conclusion: Our findings suggest that old age, hypoalbuminemia, and high body temperature may be contributory factors to increasing interface pressure; therefore, careful assessment and nursing care of these patients are needed to prevent pressure injury. Further studies are needed to establish cutoff values of interface pressure for patients with pressure ulcers.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.4
• /
• pp.47-53
• /
• 2011

The Electric Multiple Unit (EMU) has many types of door system such as sliding door, plug door etc.al. according to customer's requirements. The sliding door is widely used in Korea but has weak point in the noise problem. In the low operation speed, the noise coming from outer side of the EMU is not an important factor. As the speed is higher than before, noise is increased and make a problem. The main cause of noise is the imperfect air tightness in the EMU. The plug door system has advantages for the noise reduction characteristic in the high speed area. We have been developing electric plug-in door. The door is controlled by Door Control Unit(DCU) following the order of Automatic Train Protection (ATP) that is a kind of train signalling system. DCU has to simultaneously open and close the doors and the operation of it is related to the passengers safety. So DCU is a safety device that is important to reliability and safety. DCU is composed of several devices of control, motor driving, Input/Output, communication and power. In this paper, we will describe the functions, characteristic, requirement, subsystem and test results of DCU used for the electric plug-in door.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.4
• /
• pp.827-836
• /
• 2018

In this study, we developed a PC - based motorcycle simulator based on the development technology of a virtual patrol motorcycle training system. This simulator has been developed to be applied to a variety of fields such as driving training for beginners, driver factor research, and system development such as ABS, which can be seen in advanced models. The weight of the motorcycle operated by the patrol guards is more than 400Kg. There is a lot of risk due to the nature of work without prior practice. Therefore, we implemented a study on the untilization of physical stress and temporal pressure in emergency situations. In order to get a feeling that the motorcycle simulator is operating in real-life, it is important that the mutual reliable signal transmission and operation feel between the driver and the simulator. In order to achieve this, we developed a system that can apply the sub-systems of the actual vehicle to the motorcycle simulator in order to generate the same operation feeling as the actual vehicle. Based on these results, we have developed a method of generating a feedback queue.

• The Journal of Engineering Geology
• /
• v.18 no.2
• /
• pp.127-136
• /
• 2008

Geophysical survey for establishing a wide site for the distribution of water content, wetting front infiltration due to the rainfall, and distribution of groundwater level has been performed by using 8round penetration radar (GPR) method, electrical resistivity method, and so on. On the other hand, a narrow area survey was performed to use a permittivity method such as time domain reflectometry, frequency domain reflectometry, and amplitude domain reflectometry methods for estimating volumetric water content, soil density, and concentration of contaminant in surface and subsurface. The permittivity methods establish more corrective physical parameters than different found survey technologies mentioned above. In this study for establishment of infiltration behaviors for wetting front in the unsaturated soil caused by an artificial rainfall, soil physical parameters for volumetric water content, pore water pressure, and pore air pressure were measured by FDR measurement device and pore water pressure meter which are installed in the unsaturated weathered granite soil with different depths. Consequently, the authors were proposed to a new establishment method for analyzing the variations of volumetric water content and wetting front infiltration from the responses of infiltrating pore water in the unsaturated soil.

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.283-290
• /
• 1999

The $n^+/p/p^+$ junction PERL solar cell of $0.1{\sim}2{\Omega}{\cdot}cm$ (100) p type silicon wafer was fabricated through the following steps; that is, wafer cutting, inverted pyramidally textured surfaces etching by KOH, phosphorus and boron diffusion, anti-reflection coating, grid formation and contact annealing. At this time, the optical characteristics of device surface and the efficiency of doping concentration for resistivity were investigated. And diffusion depth and doping concentration for n+ doping were simulated by silvaco program. Then their results were compared with measured results. Under the illumination of AM (air mass)1.5, $100\;mW/cm^2$ $I_{sc}$, $V_{oc}$, fill factor and the conversion efficiency were 43mA, 0.6 V, 0.62. and 16% respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.369-377
• /
• 2013

This paper deals with the state of charge(SOC) and life cycle evaluation algorithm for lead-acid battery, which is essential factor of the electric vehicle(EV) and the stabilization of renewable energy in the smart grid. In order to perform the effective operation of the lead-acid battery, SOC and life cycle evaluation algorithm is required. Specific gravity with the change of electrolyte temperature inside battery case should be obtained to evaluate the SOC of lead-acid battery, however it is difficult to measure the electrolyte temperature of sealed type lead-acid battery. To overcome this problem, this paper proposes the equation of thermal transmission to compensate internal temperature of the lead-acid battery. Also, it is difficult to exactly evaluate the life cycle of battery, depending on the operation conditions of lead-acid battery such as charging and discharging state, self discharging rate and environmental issue. In order to solve the problem, this paper presents the concept for gravity accumulation of charge and discharge cycle, which is the value converted at $20^{\circ}C$. By using the proposed algorithm, this paper propose the test device based on the Labview software. The simulation results show that it is a practical tool for the maintenance of lead-acid battery in the field of industry.