• 농업생명과학연구
• /
• 제46권1호
• /
• pp.17-27
• /
• 2012

본 연구는 산악형 국립공원으로 분류된 6개 국립공원 53개 노선 204.5 km 구간을 대상으로 탐방로의 물리적 특성 및 훼손유형, 훼손정도 등을 파악하여 공원관리를 위한 기초자료로 활용하기 위해 수행되었다. 탐방로의 물리적 특성을 조사한 결과, 노면의 평균경사는 $14.6^{\circ}$, 평균 노폭은 1.5 m, 평균 나지폭은 1.1 m로 조사되었고, 훼손유형은 6개의 유형이 2,686회 나타났으며, 노면침식 현상이 전체 훼손유형의 37%로 가장 많은 발생을 보였다. 다음으로 뿌리노출 현상, 노폭확대 현상, 분기 현상, 암석노출 현상, 비탈붕괴 현상 순으로 조사되었고, 훼손정도를 조사한 결과, "건전" 구간이 165.34 km로 80.9%를 차지하고 있었고, "강" 구간이 9.08 km, "중" 구간이 12.69 km, "약" 구간이 17.39 km로 훼손구간은 39.16 km에 훼손율은 19.1%로 조사되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 A
• /
• pp.309-310
• /
• 2006

The considerations for remaining life of ACSR (Aluminum Stranded Conductors Steel Reinforced) in transmission lines has become gradually important to hold reliability and stability of power supply. The remaining life of ACSR exposed to the atmosphere for a long period may rely on deterioration caused by environmental indices such as atmospheric corrosion, galvanic corrosion, crevice corrosion and fatigue corrosion. This paper deals with material characteristic of ACSR due to eccentricity at sleeve point. Test samples are ACSR 240[$mm^2$] conductors, which are real transmission lines. As a result, it is obvious that ACSR due to eccentricity may lead to mechanical deterioration.

• 한국전기전자재료학회논문지
• /
• 제34권2호
• /
• pp.136-141
• /
• 2021

Heating cables, widely used in office buildings, factories, streets and railways, deteriorate in electrical insulation during operation. The insulation deterioration of heating cables leads to electric discharges that can cause electrical fires. With this background, this paper dealt with a condition monitoring technique for heating cables by the analysis of discharge signals to prevent electrical fires. Insulation deterioration was simulated using an arc generator specified in UL1699 under AC operation, and the characteristic and propagation of discharge signals were analyzed on a 100 meter-long heating cable. Discharge signals produced by insulation deterioration were detected as a voltage pulse because they are as small as a few mV and they are attenuated through propagation path. The frequency spectrum of discharge signals mainly existed in the range from 70 kHz to 110 kHz, and the maximum attenuation of the signal was 84.8% at 100 meters away from the discharge point. Based on the experimental results, a monitoring device, which is composed of a high pass filter with the cut-off frequency of 70 kHz, a comparator, a wave shaper and a microprocessor, was designed and fabricated. Also, an algorithm was designed to discriminate the discharge signal in the presence of noise, compared with the pulse repetition period and the number of pulse counts per 100ms. In the experiment, the result showed that the prototype monitoring device could detect and discriminate the discharge signals produced at every discharge point on a heating cable.

• Structural Engineering and Mechanics
• /
• 제86권5호
• /
• pp.663-671
• /
• 2023

Freeze-thaw cycles induce strength loss at the frozen soil-concrete interface and deterioration of bonding, which causes construction engineering problems. To clarify the deterioration characteristics of the interface under the freeze-thaw cycle, a frozen soil-concrete sample was used as the research object, an interface scanning electron microscope test under the freeze-thaw cycle was carried out to identify the micro index information, and an interface shear test was carried out to explore the loss law of interface shear strength under the freeze-thaw cycle. The results showed that the integrity of the interface was destroyed, and the pore number and pore size of the interface increased significantly with the number of freeze-thaw cycles. The connection form gradually deteriorates from surface-to-surface contact to point-to-surface contact and point-to-point contact, and the interfacial shear strength decreases the most at 0-3 freeze-thaw cycles, with small decreases from to 3-8 cycles. After 12 freeze-thaw cycles, the interfacial shear strength tends to be stable, and shear the failure occurs internally in the soil.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권10호
• /
• pp.469-475
• /
• 2003

Resistive leakage current flowing ZnO blocks increases with its ages, which is an important indicator of arrester deterioration. However, a complicated circuitry is essential to measure the resistive leakage current included in the total leakage current, and the difficult handling of the measurement makes few applications to the fields. In this paper, we propose a resistive leakage current measurement device which is composed of a current detection circuit and an analysis program operated on a microprocessor. The device samples the input leakage current waveform digitally, and discriminate the zero-cross and the peak point of the waveform to analyze the current amplitude vs. phase. The capacitive leakage current is then eliminated from the total leakage current by using an algorithm to extract the resistive leakage current only. Also, the device can be operated automatically and manually to analyze the resistive leakage current even when the leakage current waveform is distorted due to various types of arrester deterioration. To estimate the performance of the device, we carried out a test on ZnO blocks and lightning arresters. From the results, it is confirmed that the device could analyze most parameters needed for the arrester diagnostics such as total leakage current. resistive leakage current, and the $3^rd$ harmonic leakage current.

• 전기학회논문지
• /
• 제61권5호
• /
• pp.711-716
• /
• 2012

To assess the insulation deterioration of stator windings, diagnostic and AC breakdown tests were performed on the eleven high voltage (HV) motors rated at 6kV. After completing the diagnostic tests, the AC overvoltage test was performed by gradually increasing the voltage applied to the stator windings until electrical insulation failure occurred, to obtain the breakdown voltage. Stator winding of motors 1, 3, and 8 failed at above rated voltage at 14 kV, 13.8kV, and 16.4kV, respectively. The breakdown voltage of three motors was higher than expected for good quality windings in 6kV motors. Based on deterioration evaluation criteria, the stator winding insulation of eleven HV motors are confirmed to be in good condition. The turning point of the current, $P_{i2}$, in the AC current vs. voltage characteristics occurred between 5kV and 6kV, and the breakdown voltage was low between 13.8kV and 16.4kV. There was a strong correlation between the breakdown voltage and various electrical characteristics in diagnostic tests including Pi2.

• 한국인쇄학회지
• /
• 제30권1호
• /
• pp.59-69
• /
• 2012

This study is Long term preservation measures which is closely related to preserving paper records, record condition evaluation, preservation measure and is conducted as follows. As for Means to Evaluate the Deterioration and Damaged Conditions of Records, research and analysis has been made on the contamination and deterioration examples such as damage, dry, stapler, metal, contamination, acidification which are the characteristics of paper record damage types. The of Paper record is one of the key procedures to evaluate the record material and its physi-chemical status in many criteria and to suggest the best preservation method. Between 1970 and 2000, the main record materials was fine paper and OMR paper along with partly newspaper and coarse paper, whereas the main recording material was ball point pen. Overall damage and deterioration status is, for record materials between 1940 and 1960, high deterioration was found and in urgent need for preservation measure and more damages are caused by tapes, staplers and metals. As for records after 1970, there is light deterioration but needs preservation process. There are approximately 3 million records produces before 2000, and assuming that there are 30 pages per record and that 30% has been damaged or deteriorated, 27 million pages are subject to preservation process. Among damaged or deteriorated records, there are large number of records impossible to go through deacidification process so manual preservation and restoration process is necessary as well. Securing manpower having preservation and restoration skills as well as preservation equipment(deacidification process, preservation and restoration) is in urgent need.

• 소음진동
• /
• 제10권3호
• /
• pp.474-479
• /
• 2000

Piston slap is not only one of the major sources of noise and vibration in internal combustion engines but also a cause of the deterioration of engine performance. The basic mechanism associated with the piston slap seems to be quite simple but the phenomenon is in fact complicated with regard to many mechanical elements associated, First of all the impact force of piston slap must be identified to estimate engine block surface vibration, In this paper model of collision point is proposed to calculate the impact force when slap surface vibration. In this paper model of collision point is proposed to calculate the impact force when slap occurs. The parameters of the model are estimated by employing the concept of point mobility, . The predicted and experimentally observed vibration results confirm that the proposed method is practically useful.

• Structural Engineering and Mechanics
• /
• 제11권5호
• /
• pp.565-574
• /
• 2001

Experimental investigation into the behaviour of half-scale brick masonry panels were conducted under cyclic loading normal to the bed joint and parallel to the bed joint. For each cycle, full reloading was performed with the cycle peaks coinciding approximately with the envelope curve. Unloading, however, was carried out fully to zero stress level and partially to two different stress levels of 25 percent and 50 percent of peak stress. Stability point limit exhibits a unique stress-strain curve for full unloading but it could not be established for partial unloading. Common point limit was established for all unloading-reloading patterns considered, but its location depends on the stress level at which unloading is carried to. Common point curves were found to follow an exponential formula, while residual strains versus envelope strains can be expressed by a polynomial function of a single term. The relation between residual strain and envelope strain can be used to determine the stress level at which deterioration due to cyclic loading began.

• 상하수도학회지
• /
• 제20권6호
• /
• pp.829-836
• /
• 2006

The reaction rate of denitrification is primarily affected by the utilization of organics that are usually limited in the anoxic period in a sequencing batch reactor. It is necessary to add an extemal carbon source for sufficient denitrification. An adaptive model of state-space based on the extended Kalman filter is applied to manipulate the dosage rate of extemal carbon automatically. Control strategies for denitrification have been studied to improve control performance through simulations. The normal control strategy of the constant set-point results in the overdosage of external carbon and deterioration of water quality. To prevent the overdosage of external carbon, improved control strategies such as the constrained control action, variable set-point, and variable set-point after dissolved oxygen depletion are required. More stable control is obtained through the application of the variable set-point after dissolved oxygen depletion. The converging value of the estimated denitrification coefficient reflects conditions in the reactor.