• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.3
• /
• pp.202-210
• /
• 2013

As incomes increase, interest in ocean leisure picks up. As a result, a lot of research and developments on hull form design and production of planing boats, mostly used for ocean leisure, are needed. Analysis in researches on resistance of planing boats shows that resistance characteristic of planing boats is different from resistance characteristic of general boats because the former is fast, and its wetted surface is very small. Using Savitsky formula widely used in the calculation of effective horse power in shipbuildingyards, and propulsion system and engine manufacturers, this study calculated total resistance of a research planing boat. Then it analyzed the flow characteristics of the planing boat through theoretical analysis and wind tunnel experiment, and computed air resistance and lift force by changes of speed and trim angle. It also compared and analyzed result of theoretical analysis and experiment of the ratio of air resistance to total resistance under variations of velocity and trim angle. When the study is used to estimate more accurate effective horse power, it is expected to remedy abuses of unnecessarily installing high-powered engine. As nature disasters due to abnormal changes of weather increase, interest in greenhouse gas grows. International Maritime Organization (IMO) legislated Energy Efficiency Design Index (EEDI) and Energy Efficiency Operational Indicator (EEOI) to reduce ship greenhouse gas emissions. But this index will be applied to over 400 tons ships, small ships, emitting more greenhouse gases than larege ships per unit power, will dodge the regulations. Thus, this study indicated a problem by calculating greenhouse gas emissions of an ocean leisure planning boat (a small ship), and suggested the need for EEDI of small ships.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.22 no.1
• /
• pp.53-66
• /
• 1980

The research work is concerned with the analytical and experimental studies on the heat transfer phenomenon around the underground concrete digester used for biogas production Systems. A mathematical and computational method was developed to estimate heat losses from underground cylindrical concrete digester used for biogas production systems. To test its feasibility and to evaluate thermal parameters of materials related, the method was applied to six physical model digesters. The cylindrical concrete digester was taken as a physical model, to which the model,atical model of heat balance can be applied. The mathematical model was transformed by means of finite element method and used to analyze temperature distribution with respect to several boundary conditions and design parameters. The design parameters of experimental digesters were selected as; three different sizes 40cm by 80cm, 80cm by 160cm and l00cm by 200cm in diameter and height; two different levels of insulation materials-plain concrete and vermiculite mixing in concrete; and two different types of installation-underground and half-exposed. In order to carry out a particular aim of this study, the liquid within the digester was substituted by water, and its temperature was controlled in five levels-35。 C, 30。 C, 25。 C, 20。C and 15。C; and the ambient air temperature and ground temperature were checked out of the system under natural winter climate conditions. The following results were drawn from the study. 1.The analytical method, by which the estimated values of temperature distribution around a cylindrical digester were obtained, was able to be generally accepted from the comparison of the estimated values with the measured. However, the difference between the estimated and measured temperature had a trend to be considerably increased when the ambient temperature was relatively low. This was mainly related variations of input parameters including the thermal conductivity of soil, applied to the numerical analysis. Consequently, the improvement of these input data for the simulated operation of the numerical analysis is expected as an approach to obtain better refined estimation. 2.The difference between estimated and measured heat losses was shown to have the similar trend to that of temperature distribution discussed above. 3.It was found that a map of isothermal lines drawn from the estimated temperature distribution was very useful for a general observation of the direction and rate of heat transfer within the boundary. From this analysis, it was interpreted that most of heat losses is passed through the triangular section bounded within 45 degrees toward the wall at the bottom edge of the digesten Therefore, any effective insulation should be considered within this region. 4.It was verified by experiment that heat loss per unit volume of liquid was reduced as the size of the digester became larger For instance, at the liquid temperature of 35˚ C, the heat loss per unit volume from the 0. 1m$^3$ digester was 1, 050 Kcal/hr m$^3$, while at for 1. 57m$^3$ digester was 150 Kcal/hr m$^3$. 5.In the light of insulation, the vermiculite concrete was consistently shown to be superior to the plain concrete. At the liquid temperature ranging from 15。 C to 350 C, the reduction of heat loss was ranged from 5% to 25% for the half-exposed digester, while from 10% to 28% for the fully underground digester. 6.In the comparison of heat loss between the half-exposed and underground digesters, the heat loss from the former was fr6m 1,6 to 2, 6 times as much as that from the latter. This leads to the evidence that the underground digester takes advantage of heat conservation during winter.

• Korean Journal of Construction Engineering and Management
• /
• v.12 no.6
• /
• pp.65-78
• /
• 2011

Construction business, which is complex and long-term business, requires accurate estimation and verification in construction costs and payment procedure from project planning to the completion of construction phase. And more importantly, it is necessary to investigate and determine the risk factors related to construction costs during the entire process including design planning, construction drawings, and quantity calculating. But, currently, it is not seem to be adequate to cope with the risk and increased construction costs against the operational budget in terms of actual costs when screening and estimating the bidding cost of public apartment. Therefore, this study selected and analyzed 40 sites' report of construction completion account from 2004 to 2010 focused on the adequacy on the modification of contract and design planning and on the complication of the budget in the beginning of the project. This study deducted various risk causes and results by analyzing actual costs according to year, architectural area, region, construction cost and sale/lease classification. We could find out construction risk according to annual variation of government policy and economy, and also deducted risk items by construction characteristic according to region and architectural area. Study result, we first found out the problems of lowest price award system according to the construction costs. The weight of the cost increase risk was analyzed that subcontract and material costs are very high. Roof and tile work were analyzed highly in subcontract cost risk and reinforcing bar and cement were analyzed highly in material cost risk, among direct construction cost. Finally, this study results could be used in comparing the categories of the construction costs made by specific construction process, belonging to the construction costs, with the operational budget made in the beginning of the project that can enable to grasp unpredictable risks over the construction costs and making quantitative analysis for it through analyzing the range of fluctuation and variations led by the fluctuations in the actual construction costs.

• Korean Journal of Heritage: History & Science
• /
• v.40
• /
• pp.243-270
• /
• 2007

Linked pearls pattern expressed on textiles have no limited scale or shape when manufacturing, so they are free in expression. And from the design, material, and color we can analogize the social culture of that age. Oriental linked pearls pattern was started from the Sasanian Persia and introduced through the Silk Road, so it is closely connected with the East and the West culture. This study will consider from the 5th century to the 10th century; the mural costume of the West Central Asia, the ancient textiles excavated from the Sinjiang and Qinghai area of China, and the linked pearls pattern which are collected at Shosoin, Japan. And from this study, will concentrate on clarifying the linked pearls pattern's condition of the cultural exchange between the East and the West and it's structural variation process. The design of linked pearls pattern delivered to the East through the Silk Road is differed by area. For example, in the Western Pamir Plateau, where the ancient Sogdians mainly lived, the excavated linked pearls pattern's subject were deer or cassowary variated from the West Asian motif. But the ones excavated from Kucha Xingang had Chinese motifs added so they showed Chinese characters or Buddhist Bodhisattva image instead of Helios. Like this, the appearance of new patterns, which were accompanied by structural variations, gradually deviated from the standardized pattern of the Sasanian Persia. And this structural variation process has relations with the construction and arrangement method of various patterns of the after ages. The foliated floral Spray, which is placed at the lozenge space of linked pearls' space, had developed into ogival - shaped pattern (Neunghwamun). And the prevalence of geometrical structure pattern after the 10th century and the unfolding method of Tapjamun which is arranging unit pattern in order, are similar to the linked pearl pattern. In brief, linked pearls pattern accompanied by technical improvement let us understand the polished artistic code from its expression, and has importance in showing universal pattern beyond region and culture.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.2
• /
• pp.339-349
• /
• 1999

The dental structure substituted by restorative materials may produce discomfort resulting from hot or cold stimuli. To investigate the effects of this stimuli on the human teeth, thermal analysis was carried out by calculation of general heat conduction equation in a modeled tooth using numerical method. The method has been applied to axisymmetric and two-dimensional model, analyzing the effects of constant temperature $4^{\circ}C\;and\;60^{\circ}C$. That thermal shock was provided for 2 seconds and 4 seconds, respectively and recovered to normal condition of $20^{\circ}C$ until 10 seconds. The thermal behavior of tooth covered with a crown of gold or stainless steel was compared with that of tooth without crown. At the same time, the effects of restorative materials(amalgam, gold and zinc oxide-eugenol(ZOE)) on the temperature of PDJ(pulpo-dentinal junction) has been studied. The geometry used for thermal analysis so far has been limited to two-dimensional as well as axisymmetric tooth models. But the general restorative tooth forms a cross shaped cavity which is no longer two-dimensional and axisymmetric. Therefore, in this study, the three-dimensional model was developed to investigate the effect of shape and size of cavity. This three-dimensional model might be used for further research to investigate the effects of restorative materials and cavity design on the thermal behavior of the real shaped tooth. The results were as follows; 1. When cold temperature of $4^{\circ}C$ was applied to the surface of the restored teeth with amalgam for 2 seconds and recovered to ambient temperature of $20^{\circ}C$, the PDJ temperature decreased rapidly to $29^{\circ}C$ until 3 seconds and reached to $25^{\circ}C$ after 9 seconds. This temperature decreased rather slowly with stainless steel crown, but kept similar temperature within $1^{\circ}C$ differences. Using the gold as a restorative material, the PDJ temperature decreased very fast due to the high thermal conductivity and reached near to $25^{\circ}C$ but the temperature after 9 seconds was similar to that in the teeth without crown. The effects of coldness could be attenuated with the ZOE situated under the cavity. The low thermal conductivity caused a delay in temperature decrease and keeps $4^{\circ}C$ higher than the temperature of other conditions after 9 seconds. 2. The elapse time of cold stimuli was increased also until 4 seconds and recovered to $20^{\circ}C$ after 4 seconds to 9 seconds. The temperature after 9 seconds was about $2-3^{\circ}C$ lower than the temperature of 2 seconds stimuli, but in case of gold restoration, the high thermal conductivity of gold caused the minimum temperature of $21^{\circ}C$ after 5 seconds and got warm to $23^{\circ}C$ after 9 seconds. 3. The effects of hot stimuli was also investigated with the temperature of $60^{\circ}C$. For 2 seconds stimuli, the temperature increased to $40^{\circ}C$ from the initial temperature of $35^{\circ}C$ after 3 seconds of stimuli and decreased to $30^{\circ}C$ after 9 seconds in the teeth without crown. This temperature was sensitive to surface temperature in the teeth with gold restoration. It increased rapidly to $41^{\circ}C$ from the initial temperature of $35^{\circ}C$ after 2 seconds and decreased to $28^{\circ}C$ after 9 seconds, which showed $13^{\circ}C$ temperature variations for 9 seconds upon the surface temperature. This temperature variations were only in the range of $5^{\circ}C$ by using ZOE in the bottom of cavity and showed maximum temperature of $37^{\circ}C$ after 3 seconds of stimuli.

• Journal of the Korea Concrete Institute
• /
• v.19 no.1
• /
• pp.121-130
• /
• 2007

To investigate the enhancement in strength and deformation capacities of concrete confined by FRP composites, tests under axial loads were carried out on three groups of thirty six short columns in circular section with diverse GFRP confining reinforcement. The major test variables considered include fiber content or orientation, wrap or tube type by varying the end loading condition, and continuous or discontinuous confinement depending on the presence of vortical spices between its two halves. The circumferential FRP strains at failure for different types of confinements were also investigated with emphasis. Various analytical models capable of predicting the ultimate strength and strain of the confined concrete were examined by comparing to observed results. Tests results showed that FRP wraps or tubes provide the substantial increase in strength and deformation, while partial wraps comprising the vertical discontinuities fail in an explosive manner with less increase in strength, particularly in deformation. A bilinear stress-strain response was observed throughout all tests with some variations of strain hardening. The failure hoop strains measured on the FRP surface were less than those obtained from the tensile coupons in all tests with a high degree of variation. In overall, existing predictive equations overestimated ultimate strengths and strains observed in present tests, with a much larger scatter related to the latter. For more accuracy, two simple design- oriented equations correlated with present tests are proposed. The strength equation was derived using the Mohr-Coulomb failure criterion, whereas the strain equation was based on entirely fitting of test data including the unconfined concrete strength as one of governing factors.

• Horticultural Science & Technology
• /
• v.28 no.4
• /
• pp.567-573
• /
• 2010

Research was initiated to investigate early establishment characteristics and germination pattern of fine-textured fescues (FF). Six varieties from Chewings fescue ($Festuca$ $rubra$ L. ssp. $commutata$ Gaud., CF), creeping red fescue ($F.$ $rubra$ L. ssp. $rubra$ Gaud., CRF), hard fescue ($F.$ $ovina$ ssp. $longifolia$ Thuill., HF) and sheep fescue ($F.$ $ovina$ L., SF) were evaluated in the study. An alternative environmental condition requiring a FF germination test by International Seed Testing Association (ISTA) was applied in the experiment, consisting of 8-hr light at $25^{\circ}C$ and 16-hr dark at $15^{\circ}C$ (ISTA conditions). Daily and cumulative germination patterns were measured and analyzed on a daily basis. Significant differences were observed in germination pattern, days to the first germination, days to 50% germination, days to 60% germination, and germination rate. The final germination percentage was variable with species and varieties, being 40.25 to 82.00% at the end of study. There were considerable variations in early germination characteristics and germination pattern among FF species. The first germination in all entries except HF was initiated between 5 and 6 DAS (days after seeding) under ISTA conditions, while HF between 6 and 7 DAS, being 1 day later. It was 8 to 10 DAS in days to the 50% germination, which was 2 to 4 days after the first germination date. Days to the 60% germination were 9.10 to 14.80 DAS under ISTA conditions, being 5.70 days in differences among the entries. CF 'Jamestown II' and 'Shadow II' and HF 'Aurora Gold' were the fast varieties. The slowest one was HF 'Rescue 911'. Among FF species, turf establishment speed was becoming faster in CRF, SF, HF and CF in this order. Information on differences in germination characteristics and pattern from this study would be usefully applied for golf course design and construction, when established with FF.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.1
• /
• pp.49-64
• /
• 2014

Seabed beneath and near the coastal structures may undergo large excess pore water pressure composed of oscillatory and residual components in the case of long durations of high wave loading. This excess pore water pressure may reduce effective stress and, consequently, the seabed may liquefy. If the liquefaction occurs in the seabed, the structure may sink, overturn, and eventually fail. Especially, the seabed liquefaction behavior beneath a gravity-based structure under wave loading should be evaluated and considered for design purpose. In this study, to evaluate the liquefaction potential on the seabed, numerical analysis was conducted using 2-dimensional numerical wave tank. The 2-dimensional numerical wave tank was expanded to account for irregular wave fields, and to calculate the dynamic wave pressure and water particle velocity acting on the seabed and the surface boundary of the structure. The simulation results of the wave pressure and the shear stress induced by water particle velocity were used as inputs to a FLIP(Finite element analysis LIquefaction Program). Then, the FLIP evaluated the time and spatial variations in excess pore water pressure, effective stress and liquefaction potential in the seabed. Additionally, the deformation of the seabed and the displacement of the structure as a function of time were quantitatively evaluated. From the analysis, when the shear stress was considered, the liquefaction at the seabed in front of the structure was identified. Since the liquefied seabed particles have no resistance force, scour can possibly occur on the seabed. Therefore, the strength decrease of the seabed at the front of the structure due to high wave loading for the longer period of time such as a storm can increase the structural motion and consequently influence the stability of the structure.

• Asian Journal of Turfgrass Science
• /
• v.24 no.2
• /
• pp.79-87
• /
• 2010

Research was initiated to investigate the early establishment characteristics and germination patterns of perennial ryegrass (PR, Lolium perenne L.). Eight cultivars of PR were evaluated in the study. Experiment was conducted under a room temperature condition of $6^{\circ}C$ to $23^{\circ}C$ (natural conditions). Daily and cumulative germination patterns were measured and analyzed on a daily basis. Significant differences were observed in germination pattern, days to the first germination, days to 50% germination, days to 75% germination, and germination percentage with different environments and cultivars. Germination percentage was variable with cultivars at the end of study. It was 66.25 to 93.50% under natural conditions. There were considerable variations in the early germination characteristics and germination pattern among the entries according to different conditions. The first germination was initiated between 3 and 5 DAS (days after seeding) under ISTA (International Seed Testing Association) conditions. But it started between 6 and 8 DAS under natural conditions, being 2 to 4 days later as compared with that under ISTA conditions. It was 8 to 12 DAS that reached to days to the 50% germination, which was 2 to 5 days after the first germination. Days to the 75% germination were 10.08 to 13.70 DAS under natural conditions, being 2.07 to 5.70 days slower as compared with ISTA conditions. 'Pennant II' was the fastest cultivar. But the slowest was 'Catalina II' that was 3.62 days later than 'Pennant II' under natural conditions. Considering days to the first germination, days to 75% germination, and germination pattern etc, 'Pennant II' and 'Brightstar II' were regarded as excellent cultivars under both conditions. From this study, information on differences in germination characteristics and patterns would be usefully applied for golf course design and construction, when established with PR.

• Journal of Science of Art and Design
• /
• v.12
• /
• pp.65-96
• /
• 2007

Today, the modern art is extremely diverse. It is denying its own boundary through chaos, extreme, abjection. In fact the diversity of the modern art can be best described as questioning and challenging to the essence of the reality, rather than the artistic pursuit of the beauties. The pursuit of the reality has been a long lasting discourse since the ancient. Through the history, the reality (referent) and representation (image) has been complementing and disposing each other in a relationship of a meaningful construction until the modern times. The limit of modernistic self-reference and the emergence of the figure leads to the emergence of Post-modernism in a trend of experimenting new visual arts. The return to the figure is clearly distinguished from existing representation's system and it brought new meanings to approaches and interpretations of the reality. In the case of Pop arts of 1960's and the following the modern sculptures, which is covered by this thesis, I put an emphasis on the diversification of those via changed strategies on the reality. In a situation where the reality is dictated by signified, the modern arts can no longer stay on a classic concept of representation, rather it pursuits new system and diverse strategies. I provide three types of strategic characters of the reality and the diversification of reality: the transition of the reality. These three types can be used as a frame work, which is supporting new aspects of the modern arts in reflecting on existing system. Therefore, the reason of categorizing is to distinguish modernistic arts and post modernistic arts, and to propose new post-modernistic discourses. Adapting J.F, Lyotard's view, absence is used to trace down the diversification of the reality thorough the sublime on the deconstruction of the mega discourses and the relationship of representation. Based on H. Faster's theory of the appropriation, the appropriation is used to exemplify the strategies of visual arts are in variations and being delayed. Lastly, in the transition, J. Baudrilliard's simulacre is used in terms of the concept of post modernistic representation. Based on the core of his theories, the deconstruction of existing concepts and simulation as the post modernistic representation, and the world of hyperreality based on simulacre are explained. These allows us to deny that representation is the expression of reality through mimesis. My aim is to work on the definition of the arts and representation in the modern era, and go further from there in order to clarify meaning and extension of the modern sculptures. Now two artists are reviewed based on their own art works: George Seagal; Jeff Koons. They are selected among numerous artists from the Post Modern era. Epic contents and emphasis on daily life of Seagal's works show good examples to artists from Pop Arts and following time period and may have served as a start point for Postmodernism. Indeed, he tried to show a newly defined relationship between art works and daily life experience. On the other hand, J.Koons used the strategies of fabrication and appropriation, which shows characteristics of the postmodernism. Through his four individual exhibitions, he shows the diversification of the reality based on art works as fetishistic merchandises, and newly defined concept of Ready-made since M Duchamp. Lastly, the diversification of the reality is analyzed again in context of my art works. I focused on the return to the figure among a variety of trends of late 20 th century modern sculpture. It showed the post modernistic point of view on the reality. Post modernistic diversified strategies are adopted as a method of distinguishing each art works via the diversification of the reality. This is the result of contemporary social and cultural situations.