• Polymer(Korea)
• /
• v.34 no.3
• /
• pp.237-241
• /
• 2010

Mechanical characteristics and chemical resistance have been investigated for PC/PBT blends. The changes in mechanical performance of PC/PBT blends was monitored during the treatment with both the PC thinner and general-purpose thinner to figure out the chemical resistance. The PC thinner greatly affected the mechanical properties of PC/PBT blends compared with general-purpose thinner. In the case of PC thinner treatment, the mechanical performance was improved with increased PC content at lower PC content ranges, say below 50%. However the mechanical performance was dropped rapidly at higher PC content ranges due to poor chemical resistance of PC. Transparent pure PC specimen became opaque after chemical treatment with PC thinner, and this can be interpreted by solvent-induced crystallization.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.3
• /
• pp.1058-1062
• /
• 2011

After the design and production of cold rolling to make titanium-alloyed(Gr.9) eyerim, the function of the roller was evaluated. The surface roughness values of the roller of Ra was $0.05{\sim}0.156{\mu}m$ and of Rz was $0.23{\sim}067{\mu}m$. The values showed a satisfactory result compared with the surface roughness values Ra was $0.04{\mu}m$ and Rz was $0.3{\mu}m$ which was measured after barrel polishing for the titanium eyeglasses frame PVD (Physical Vapor Deposition) gilding. As a result of cold rolling of Ti-3Al-2.5V (Half Titanium), the degree of hardness increased to 221Hv, 247Hv(1st), 270Hv(2nd), etc. Therefore, it was found that proper heat treatment and multi-stand rolling process are necessary.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.3
• /
• pp.604-610
• /
• 2007

Injection molding is the most common method of shaping plastic resins for manufacturing a variety of parts. This injection molding is accomplished by injection molding machines (IMM) which consists of a hewer, a reciprocating screw, barrel assembly, and an injection nozzle. The plastic resin is fed to the machine through the hopper and it should be heated to the target melting temperature, which depends on material properties, as closely as possible with very small temperature overshoot in the barrel. Since the barrel, which has temperature dependent specific heat and thermal conductivity in the operating temperature range, is heated by the several electric heater bands, it is not an easy task to control the temperature of the barrel owing to the interference of neighboring heaters and its material properties. Though PID controller with auto-tuning capability is widely adopted in the nm, the auto-tuning process should be carried out whenever the operating temperature is changed significantly. Recently, though the predictive controller is developed and shows good performance, it has drawbacks: 1. Since the heat transfer modeling process is very complicated and should be carried out again when the barrel is changed, it is somewhat inappropriate in the field. 2. The controller performance is not validated in whole operating temperature range. In this paper, cascade type simple PI controller with input restriction is proposed to find the possibility of controlling the barrel temperature in the whole operating temperature range. It is shown by experiment that the proposed controller shows good performance. This result can be applied to design of PI controller with auto-tuning capability.

• Journal of Korean Society of Transportation
• /
• v.30 no.4
• /
• pp.33-42
• /
• 2012

Recent development and penetrating expansion in ICT(Information and Communication Technology) has brought considerable improvements in transportation services. However, there is a controversial debate whether transportation and communications behave as substitutes or as complements to one another. On this subject, recent studies considered those two industries as services, but transportation and communications are broadly put for intermediary goods into other industries. Hence, it is essential to examine this issue from understanding their relationships to each other with respect to manufacturing and services. In this study, input-output tables of benchmark years from 1980 to 2005 have been analysed to explore the relationships between transportation and communications using Spearman's correlation analysis. The results show that both industries had complementary roles over the period, but, to some extent, changed into substitution roles in some categories.

• Cartoon and Animation Studies
• /
• s.14
• /
• pp.83-99
• /
• 2008

In general, the cut or dissolve or etc., collective changeover represents the change of scene in the film. Animation film makes scene's various parts to allow intended sensibility and narrative factors by special manufacturing skill generating frame image one by one and transfer it to the different symbolic dimensional expression. Nowadays sequential scene composition is not any more the unique special treatment for 2D animation according to image handling skill like morphing, metamorphosis, etc. becomes diverse and elaborate. But 2D manual animation makes spectator to be absorbed into different visual dimensions continuously and strongly beyond character and background, namely object and space. that is 2D manual animation's strong attractiveness. Finally these characteristics enable literary function which makes it possible to do delicate metaphorical through full scene composition basis and to communicate a implicative meaning system The analysis about scene broke boundary between symbolic perspective world and plane formative world and it became more diverse and complicated. Hereupon the analyzing the composition basis of formative element in the animation film scene and it's application effect make it helpful to analysis and application in the modern image scene having new absorbing methods

• Resources Recycling
• /
• v.24 no.3
• /
• pp.66-75
• /
• 2015

The flexural performance of amorphous steel fibers having environmental and economy benefits due to relatively short manufacturing process were evaluated as well as that of hooked steel fibers by varing fiber length and volume fraction. Fiber lengths were 10 mm, 20 mm, 30 mm and fiber volume fractions were varied from 0.3% to 1.2%. Test results with flexural performance showed that mixing design needs to be careful because of relatively high volume of amorphous steel fiber compared to hooked steel fibers. High flexural strength was obtained from both longer fiber length and higher volume fraction. Residual strength and toughness of amorphous steel fiber were similar to that of hooked steel fiber, even though rapid dropping of applied load right after concrete matrix breaking. It can be judged that relatively high ability of energy dissipation around first cracking area relatively overcome rapid dropping of loading.

• Journal of the military operations research society of Korea
• /
• v.32 no.2
• /
• pp.78-91
• /
• 2006

Recently mass customization has become a new paradigm in the global market to satisfy both the diversified demands of customers but also the efficiency of the mass production system. In this paper, mass customization is embodied by a new product development method with which various product families are produced from standard "product platform" developed from historical data. The product platform, the key concept of this proposed method, is significantly efficient as a solution to the customer demand of high variety and small quantity products. The proposed method is applied to build the platform family of naval ships, utilizing the concept of "Group Technology". In addition, cost effectiveness of the proposed method is analyzed and the applicable range of requirement conditions are presented. In conclusion, some remarkable effects such as reduction in production cost and development time are expected by employing this method to the procurement process of the naval ships.

• The korean journal of orthodontics
• /
• v.47 no.2
• /
• pp.130-141
• /
• 2017

The aim of this case report was to describe an innovative orthodontic treatment method that combined surgical and orthodontic techniques. The novel method was used to achieve a positive result in a case of moderate crowding by employing a computer-guided piezocision procedure followed by the use of clear aligners. A 23-year-old woman had a malocclusion with moderate crowding. Her periodontal indices, oral health-related quality of life (OHRQoL), and treatment time were evaluated. The treatment included interproximal corticotomy cuts extending through the entire thickness of the cortical layer, without a full-thickness flap reflection. This was achieved with a three-dimensionally printed surgical guide using computer-aided design and computer-aided manufacturing. Orthodontic force was applied to the teeth immediately after surgery by using clear appliances for better control of tooth movement. The total treatment time was 8 months. The periodontal indices improved after crowding correction, but the oral health impact profile showed a slight deterioration of OHRQoL during the 3 days following surgery. At the 2-year retention follow-up, the stability of treatment was excellent. The reduction in surgical time and patient discomfort, increased periodontal safety and patient acceptability, and accurate control of orthodontic movement without the risk of losing anchorage may encourage the use of this combined technique in appropriate cases.

• The Journal of Korean Academy of Prosthodontics
• /
• v.55 no.4
• /
• pp.403-409
• /
• 2017

In the case of an extraction in the maxillary anterior region, immediate placement of implant-supported fixed prosthesis can be considered as a treatment option. Fewer surgical operations, reduced treatment time, and optimal availability of existing bone are obvious advantages of the method; however, when applied in the continuous maxillary anterior region, inter-implant distance must be carefully considered, as well as accurate diagnosis and treatment planning for predictable outcome. In this case report, immediate placement of two implants in the continuous maxillary anterior along with bone graft following the extraction of root rests, and the restoration of provisional and implant-supported fixed prosthesis on a 63-year-old patient had resulted in both esthetically and functionally satisfactory clinical outcomes.

• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.483-489
• /
• 2010

An image analysis-based soft sensor is designed and applied to automatic quality classification of product appearance with color-textural characteristics. In this work, multiresolutional multivariate image analysis (MR-MIA) is used in order to analyze product images with color as well as texture. Fisher's discriminant analysis (FDA) is also used as a supervised learning method for automatic classification. The use of FDA, one of latent variable methods, enables us not only to classify products appearance into distinct classes, but also to numerically and consistently estimate product appearance with continuous variations and to analyze characteristics of appearance. This approach is successfully applied to automatic quality classification of intermediate and final products in industrial manufacturing of engineered stone countertops.