• Journal of the Korean Home Economics Association
• /
• v.44 no.1 s.215
• /
• pp.47-58
• /
• 2006

The purposes of this research were to evaluate the effects of the sex education program on sexual knowledge and sexual attitude, and to provide fundamental information on sex education for middle school students. The research design was comparison and experimental groups including pre-test and post-test. The study subjects were 160 male middle school students in Pusan: 80 students of the experimental group and 80 students of the comparison group. The experimental group showed the significant differences from the comparison group in terms of sexual knowledge and sexual attitude. Through formative evaluation, students recognized human sexuality, especially in the areas of physical change, psychological change, dating, sexual drives and sexual violence. This sexual education program was designed with literature review and participated students' requests.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.785-786
• /
• 2006

Performance comparison of IPMSMs with distributed and concentrated winding is presented in this papcr. Two IPMSMs have been designed and fabricated with identical rotor dimension, air-gap length, series turn number, stator outer radius, and axial length except winding configuration. Basic parameters and machine performance, such as resistances, back emf, output torque, and efficiency, are compared. From the comparison results, motor design considering winding configuration is discussed.

• Journal of the Korean Society of Safety
• /
• v.14 no.1
• /
• pp.66-72
• /
• 1999

Local heating transportation pipe has sensor and return lines to detect water-leakage. There are impulse and resistance comparison measurement types for a water-leakage detection. The impulse type shows large detection error within a measurement range. Since the resistance comparison type can find a comparative accurate single water-leakage point in the measurement range of heating pipe, it has been used to detect water-leakages these days. However if the multi water-leakages are happened in the measurement range of transportation pipe. the resistance comparison type shows a detection error point by the parallel resistance between a detection sensor line and ground. But the detection error will be minimized by the divided transportation pipe loops. In this research, it suggests the design of remote controlled detection system which can divide a large pipe loop and a possible single water-leakage measurement process in each divided loops.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.11 no.17
• /
• pp.67-80
• /
• 1988

This study is concerned with the comparison of two time homogeneous Poisson processes. Traditionally, the methods of testing equality of Poisson processes were based on the binomial distribution or its normal approximations. The sampling plans used in these methods are to observe the processes concurrently over a predetermined time interval, possibly different for each process. However, when the values of the intensities of the processes are small, inverse type sampling plans are more appropriate since there may be cases where only a few or even no events are observed in the predetermined time interval. This study considers 9 inverse type sampling plans for the comparison of two Poisson processes. For each sampling plans considered, critical regions and the design parameters of the sampling plan are determined to guarantee the significance level and the power at some values of the alternative hypothesis. The Problem of comparing of two Weibull processes are also considered.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.139-142
• /
• 2009

Comparison of three converter topologies for single phase switched reluctance motor is proposed in this paper. Due to the limitation of do-link voltage, conventional asymmetric converter is difficult to build up enough phase current in the high speed operation. In order to solve this problem, boost converter is used to improve the performance. Two active boost converters are reviewed: one is series-connected type, another is parallel-connected. Otherwise, a novel active boost converter is proposed. The comparison of these converters is based on the voltage raring of capacitor, stability and converter topology. Because the converter selection depends on the motor design, the single phase 6/6 SRM is considered in this paper. Some simulations results are executed. And the results verified the analysis in this paper.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.5
• /
• pp.17-23
• /
• 1995

A numerical analysis on engine coolant is made by the use of FVM based general purpose 3 dimensional Navier-Stokes solver, TURB-3D. Numerical solutions are verified by comparison with the experimental data of Lotus model. The results show a good qualitative as well as quantitative comparison. Coolant flow rate control is attempted through adjusting the cross section area of passage base on the results of an original coolant passage. It is concluded from the results that the flow rate control is possible as attempted, and thus can be used in the real engine design.

• Wind and Structures
• /
• v.1 no.1
• /
• pp.77-109
• /
• 1998

An evaluation and comparison of seven of the world's major building codes and standards is conducted in this study, with specific discussion of their estimations of the alongwind, acrosswind, and torsional response, where applicable, for a given building. The codes and standards highlighted by this study are those of the United States, Japan, Australia, the United Kingdom, Canada, China and Europe. In addition, the responses predicted by using the measured power spectra of the alongwind, acrosswind and torsional responses for several building shapes tested in a wind tunnel are presented and a comparison between the response predicted by wind tunnel data and that estimated by some of the standards is conducted. This study serves not only as a comparison of the response estimates by international codes and standards, but also introduces a new set of wind tunnel data for validation of wind tunnel-based empirical expressions.

• International conference on construction engineering and project management
• /
• 2005.10a
• /
• pp.719-724
• /
• 2005

It has been debating on the performance evaluation of professional construction management (PCM) services since its introduction to Taiwan's construction industry more than a decade ago. Several evaluation systems were proposed by previous researchers. However, there has no comparison study been conducted for the feasibility, effectiveness, and appropriateness of these systems to the performance management (PM) of practical PCM services. This paper is intended for this end to compare the existing PCM performance evaluation systems in Taiwan. A real world design/build (D/B) building project was selected for case study. The result of case study concludes and compares the pro's and con's of the three systems. At the end, it recommends strategies for selecting the most appropriate PCM performance evaluation for PCM services.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.2
• /
• pp.52-60
• /
• 2002

Axiomatic Design is the one of many useful methods for making a good design. In this method, the independency of Functional Requirements (FRs) is an important property to determine whether the design is good or not. Until now so many designers have decided the independency between FRs by their own decisions. The way depending on inspiration is simple and fast, but it can not be considered as a precise conclusion. Also there are not exact rule that evaluate the quantitative independence between FRs. This paper will show the way to evaluate the quantitative independence of FRs from the comparison between FRs of lower levels, and develop more efficient and objective tool in Axiomatic Design.

• KIEAE Journal
• /
• v.15 no.6
• /
• pp.47-56
• /
• 2015

Purpose and Method: Despite benefits of building energy simulations, practitioners seem to be reluctant to use simulations for design decision making. By means of survey and interviews, this study aims to investigate domestic hindrance against increasing simulation usability, and to collect user requirement to enhance technical functionality of the simulation. Also this study compares the Information Sharing Workflow by Stantec and general domestic design process in order to identify a direction of the Integrated Design Process. Result: Finally this study wraps up with suggestions of how simulation functionality and use protocol should be in order to satisfy user requirement and also to gather more users.