• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.811-818
• /
• 2000

Agricultural chemicals spraying is one of the most efficient methods for pesticides control. General farming groups use Speed Sprayer but its deposition amount on practical crops is only 20% of total amount in SS case. Agricultural chemicals which fail to arrive the crops not only cause environmental contamination but loss of agriculture chemicals by lower deposition efficiency. For the purpose of improvement of these problems, this experiment proposes SS attachment type electrostatic induction spraying apparatus with DC power which improves deposition efficiency of agriculture chemicals on the crops.

• Analytical Science and Technology
• /
• v.9 no.1
• /
• pp.98-106
• /
• 1996

The concentration of sulfur dioxide in Wonju City was predicted using TCM (Texas Climatological Model). We have studied the transportation and wet deposition of $SO_2$ using the TCM and the analysis of rainfalls. The results are as follows : At the Hak-Sung Dong site in Wonju city, the correlation coefficient between the measured and calculated concentrations were 0.904. Sulfur dioxide was washed out by wet deposition. The wet deposition ratio to total amount of emitted sulfur dioxide was higher in summer than in autumn and winter seasons due to heavy rainfall in summer. The correlation coefficient between the precipitation and wet deposition of sulfur dioxide was 0.68. The months with greater rainfall showed that the measured concentrations of sulfur dioxide were much lower than the predicted ones. Although the amount of precipitation in April was smaller than in summer, the wet deposition ratio in April was much higher than any other months, due to the sulfur dioxide that was adsorbed on particulate matter and moisture was transported during the period of yellow sand phenomena from China.

• YAKHAK HOEJI
• /
• v.29 no.3
• /
• pp.124-129
• /
• 1985

A dissolution characteristics of phenylbutazone deposited on Avicel and dibasic calcium phosphate by solvent deposition method were studied. The solvent deposition was confirmed by scanning electron microscopy. Avicel was superior to dibasic calcium phosphate as excipient in dissolution rate. Total amount of phenylbutazone dissolved from Avicel deposition system at 30minutes were enhanced 1.2-1.6 times compared with physical mixtures of them. The dissolution rate of 10% solvent deposition system was highest and that of 75% solvent deposition system was lowest in Avicel system and dibasic calcium phosphate system. Dissolution profile of commercial products was dependent on manufacturing conditions and dissolution rate of 10% Avicel system was greater than that of commercial products.

• Journal of Pharmaceutical Investigation
• /
• v.15 no.3
• /
• pp.100-112
• /
• 1985

Dissolution characteristics of flurbiprofen solvent deposited on ${\alpha}-cyclodextrin$, ${\beta}-cyclodextrin$, lactose and corn starch were studied to evaluate the pharmaceutical aspects of solvent deposition method where drug was solvent deposited on the surface of excipients. In a solvent deposition system, the drug to excipient ratio and kind of excipient affect much on dissolution rates of flurbiprofen. The solvent deposition system formation was confirmed by scanning electron microscope. By increasing the amounts of matrix, it was possible to enhance the dissolution rate of flurbiprofen solvent deposition system. The amount of flurbiprofen dissolved from ${\beta}-cyclodextrin$ deposition system (1:10) at 60 minutes was enhanced 6.5 times in water and 28 times in simulated gastric juice compared with flurbiprofen alone. Flurbiprofen solvent deposited system (1:10) enhanced dissolution rate greater than inclusion complex and dispersion system.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.3
• /
• pp.421-426
• /
• 2004

Dry deposition fluxes of inorganic acidic species to the waterbody were measured by the dry deposition sampler (DDS). DDS was composed of three pans filled with pure water. An average concentration increase during the sampling time, after removing an abnormal value if existed, was considered as the input by deposition. Important operation parameters such as the amount of water used and sampling time were determined through a series of laboratory experiments. The deposition flux measured by DDS was compared with that by the water surface sampler developed by Yi et ai. (1997a,b).

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.159-164
• /
• 1997

Pyrolytic carbon layer was coated on A1203 balls by fluidized bed type chemical vapour deposition unit to develop the coating technology for the preparation of coated nuclear fuel. The deposition was carried out at the temperature ranges between 110$0^{\circ}C$ and 130$0^{\circ}C$ with various gas contents and flow rates. Source and carrier gas were propane and argon, respectively. X-ray analysis shows that the deposition layer was typical carbon spectra. The growth rate of carbon layer depended on the amount of source gas and the deposition temperature. For the alumina balls with 2mm in diameter, the deposition rate was 11${\mu}{\textrm}{m}$/hr in the flow gases containing 30% source gas at 130$0^{\circ}C$ with a total flow rate of 2.0$\ell$/min. Microstructural observation of the deposits with scanning electron microscope revealed that the deposits had relatively dense and isotropic structure. Chemical analysis by energy dispersive spectroscopy showed that the layer was pure carbon.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.5
• /
• pp.393-397
• /
• 2003

The effects of the composition and additives on the blackening and deposition rate of electroless Ni-Zn plating have been examined. Hydrazine resulted in lower sheet resistance of the deposit than sodium hypophosphite. Zinc concentration more than 15 wt% and small amount of ammonium sulfate in the deposits were needed in obtaining Ni-Zn deposit with a black color. An optimum condition was obtained for the black Ni-Zn deposit at an appreciable deposition rate.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.4
• /
• pp.173-178
• /
• 2003

In this paper, we studied the physical and electrical characteristics of $\textrm{WSi}_{x}$ thin film with respect to the adoption of the DCS (dichlorosiliane) post flow and the variation of deposition temperature. XRD measurements show that as deposited thin film has a hexagonal structure regardless of deposition Process. However, we find that the phase of thin film has changed to a tetragonal structure after the heat treatment at $680^{\circ}C$. Adoption of DCS post flow and increment of deposition temperature result in the increments of Si/W composition ratio. These conditions also result in the increment of sheet resistance by the amount 3.0~4.2$\Omega$/$\square$, but give the tendency in the decrement of stress by 0.27~0.3 E10dyne/$\textrm{cm}^2$. We also find that the contact resistance of word line and bit line interconnection was decreased by the amount 5.33~16.43$\mu$$\Omega$-$\textrm{cm}^2$, when applying DCS post flow and increasing deposition temperature.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.592-599
• /
• 2010

A porous nickel-tin nano-dendritic electrode, for use as the anode in a rechargeable lithium battery, has been prepared by using an electrochemical deposition process. The adjustment of the complexing agent content in the deposition bath enabled the nickel-tin alloys to have specific stoichiometries while the amount of acid, as a dynamic template for micro-porous structure, was limited to a certain amount to prevent its undesirable side reaction with the complexing agent. The ratios of nickel to tin in the electro-deposits were nearly identical to the ratios of nickel ion to tin ion in the deposition bath; the particle changed from spherical to dendritic shape according to the tin content in the deposits. The nickel to tin ratio and the dendritic structure were quite uniform throughout the thickness of the deposits. The resulting nickel-tin alloy was reversibly lithiated and delithiated as an anode in rechargeable lithium battery. Furthermore, the resulting anode showed much more stable cycling performance up to 50 cycles, as compared to that resulting from dense electro-deposit with the same atomic composition and from tin electrodeposit with a similar porous structure. From the results, it is expected that highly-porous nickel-tin alloys presented in this work could provide a promising option for the high performance anode materials for rechargeable lithium batteries.

• Journal of Korean Society for Atmospheric Environment
• /
• v.11 no.4
• /
• pp.351-359
• /
• 1995

In order to investigate geochemical behaviors of artificial radionuclide($^{137}$ Cs), the fallout deposition of arificial radioisotope($^{137}$ Cs) was measured from May to October in 1994 at the Korea Ocean Research & Development Institute(KORDI), Ansan, Kyunggido, Korea. And to study radioisotopic behavior and cumulative action in soil, soil samples were collected from Kwang-Leung Forest, Kyunggidom and artificial radioisotope ($^{137}$ Cs) and natural radioisotope($^{210}$ Pb) were identified. The amount of $^{137}$ Cs in atmosphere collected by wet deposition process in May was found to be 4.95 to 11.96mBq m$^{-2}$ whereas the amounts of $^{137}$ Cs by dry deposition process in May and October were found to be 4.0mBq g$^{-1}$ and 3.0mBq g$^{-1}$ , respectively. The amount of $^{137}$ Cs accumulated in soil was measured to be 311mBq cm$^{-2}$ , which contained 83% of the total inputs from atmospheric fallout (374 mBq cm$^{-2}$ ) since 1960s. In addition, the accumulation rate and the annual flux of $^{210}$ Pb into soils were 0.32cm yr$^{-1}$ and 34 mBq cm$^{-2}$ yr$^{-1}$ , respectively. Conclusively, it was found that arificial radioisotopes were mainly from the stratosphere and soil resupension of continental China through the troposphere.