• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.47-52
• /
• 2002

A processing method is developed for preparing sol-gel derived $Pb(Zr_{1-x}Ti_x)O_3$ (x=0.5) thin films on Pt-Ir($Pt_{80}Ir_{20}$)-alloy substrates. The as-deposited layer was dried on a plate in air at $70^{\circ}C$. And then it was baked at $1500^{\circ}C$, annealed at $450^{\circ}C$ and finally annealed for crystallization at various temperatures ranging from $580^{\circ}C$ to $700^{\circ}C$ for 1hour in a tube furnace. The thickness of the annealed film with three layers was $0.3{\mu}m$. Crystalline properties and surface morphology were examined using X-ray diffractometer (XRD). Electrical properties of the films such as dielectric constant, C-V, leakage current density were measured under different annealing temperature. The PZT thin film which was crystallized at $600^{\circ}C$ for 60minutes showed the best structural and electrical dielectric constant is 577. C-V measurement show that $700^{\circ}C$ sample has window memory volt of 2.5V and good capacitance for bias volts. Leakage current density of every sample show $10^{-8}A/cm^2$ r below and breakdown voltage(Vb) is that 25volts.

• 한국표면공학회지
• /
• 제51권2호
• /
• pp.126-132
• /
• 2018

SnS thin films with different substrate temperatures ($150 {\sim}300^{\circ}C$) as process parameters were grown on soda-lime glass substrates by RF magnetron sputtering. The effects of substrate temperature on the structural and optical properties of SnS thin films were investigated by X-ray diffraction (XRD), Raman spectroscopy (Raman), field-emission scanning electron microscopy (FESEM), energy dispersive X-ray spectroscopy (EDS), and Ultraviolet-visible-near infrared spectrophotometer (UV-Vis-NIR). All of the SnS thin films prepared at various substrate temperatures were polycrystalline orthorhombic structures with (111) planes preferentially oriented. The diffraction intensity of the (111) plane and the crystallite size were improved with increasing substrate temperature. The three major peaks (189, 222, $289cm^{-1}$) identified in Raman were exactly the same as the Raman spectra of monocrystalline SnS. From the XRD and Raman results, it was confirmed that all of the SnS thin films were formed into a single SnS phase without impurity phases such as $SnS_2$ and $Sn_2S_3$. In the optical transmittance spectrum, the critical wavelength of the absorption edge shifted to the long wavelength region as the substrate temperature increased. The optical bandgap was 1.67 eV at the substrate temperature of $150^{\circ}C$, 1.57 eV at $200^{\circ}C$, 1.50 eV at $250^{\circ}C$, and 1.44 eV at $300^{\circ}C$.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.155-155
• /
• 2017

Surface modifications are commonly utilized to adjust the properties of the titanium and its alloy surface to the specific needs of the medical applications, but there are disadvantages such as poor osteoconductive properties and low adhesion of bone cell to implant surface. In order to improve these disadvantages, changes in surface properties have an important effect on osseointegration during implantation. In this paper we applied new technological method for improving a unique surface modification using the characteristic of an electrolytic Solution. Thus, in the electrolyte containing NaF in Na2SO4, TiO2 nanoporous was uniformly formed, and HAp nanoparticles were electrodeposited around the TiO2 nanopores, but in the electrolyte containing NH4F in (NH4)H2PO4, the coarse protrusions including HAp nano particles were regularly deposited onto the TiO2 barrier layer. The surface characteristics and the distributed elements and have been investigated by EDS analysis, and ultra-fine structure of surface are carried out using FE-SEM. To investigate the behavior of the anion, the analysis of chemical states was performed by XPS, and the narrow spectrums for Ti2P, Ca 2p, and P 2p seems to be almost similar depending on the characteristics of the electrolyte solution respectively. In addition, Ca 2p spectrum could be resolved into two peaks for Ca 2p3/2 and 2p1/2 at 347.4 and 351.3 eV, which are related to hydroxyapatite. And, the P peak can also be deconvoluted into two peaks for P1/2 and P3/2 levels with binding energy 134.2 and 133.4 eV, respectively. From the result of soaking test, the apatite morphologys were well-formed onto the modified surface according to the different conditions.

• 한국안광학회지
• /
• 제7권1호
• /
• pp.75-78
• /
• 2002

파장범위 620~820nm에서 반사가 큰 $TiO_2/SiO_2$ 33층 박박 mirror를 설계하고 전자 빔 증착 방법으로 제작하였다. 다층박막은 BK7 유리 기판에 연속적으로 증착하였다. 고반사박막 설계는 중심파장 ${\lambda}_0$ 주변에 stopband가 만들어지는 것과 같은, 고굴절률을 가지는 층($n_H$)과 저굴절률을 가지는 층($n_L$)을 반복해서 하였다. 입사각 $40^{\circ}{\pm}7^{\circ}$인 투과도 측정 스펙트럼에서 전체적으로 파장범위 620~820nm에서 99.9%의 반사를 보였다. 파장이 700~740nm에서 투과도가 큰 피크를 보였다.

• 분석과학
• /
• 제30권6호
• /
• pp.319-328
• /
• 2017

The identification of explosive residues on specimens obtained from an explosion event is a crucial factor for assessing the cause of the explosion. In order to detect the components of explosives, the explosive residues deposited on surfaces are commonly extracted using swabbing materials pre-wetted with an organic solvent. The residues are then analyzed with analytical instruments such as LC/MS and CE/MS. Most conventionally used swabbing media such as cotton swabs or cotton tip swabs seem unsuitable for extracting explosive residues from the surface of a large area of clothes because the swabbing materials tend to be damaged easily, and because only a relatively small amount of explosives is collected. To overcome these problems, we have introduced a novel wiper ($215{\times}210mm$, single layer, Yuhan-Kimberly, Republic of Korea) as a swabbing material to recover representative organic explosives, namely, TNT, RDX, tetryl, HMX, PETN, and NG, from a large area of clothes. Different sides of the wiper, which was folded in half five times, was used to swab the surface of a clothing. We compared this novel wiper with a cotton swab and a cotton tip swab in terms of the recovery efficiency for the aforementioned organic explosives by pre-wetting with methanol, acetone, and acetonitrile, respectively. We identified that this novel wiper collected a significantly higher amount of organic explosive residues than a cotton swab or a cotton tip swab when using methanol as an extracting solvent.

• 한국진공학회지
• /
• 제12권2호
• /
• pp.130-135
• /
• 2003

최근, poly-Si 박막은 저가의 박막소자응용을 위하여 사용되어 왔다. 그러나, 유리기판 위에서 일반적인 고상결정화(SPC) 방식으로 poly-Si 박막을 얻기는 불가능하다. 이러한 단점 때문에 유리와 같은 저가기판 위에 poly-Si을 결정화하는 연구가 최근 다양하게 진행되고 있다. 본 논문에서는 급속열처리(RTA)를 이용하여 유연한 기판인 몰리브덴 기판 위에서 a-Si:H를 성장시킨 후 고온결정화에 대한 연구를 진행하였다 고온결정화된 poly-Si 박막은 150$\mu\textrm{m}$ 두께의 몰리브덴 기판 위에 성장되었으며 결정화 온도는 고 진공하에서 $750^{\circ}C$~$1050^{\circ}C$ 사이에서 결정화된 시료에 대하여 결정화도, 결정화 면방향, 표면구조 및 전기적 특성이 조사되었다. 결정화온도 $1050^{\circ}C$에서 3분간 결정화된 시료의 결정화도는 92%를 나타내고 있었다. 결정화된 poly-Si 박막으로 제작된 TFT 소자로부터 전계효과 이동도 67 $\textrm{cm}^2$/Vs을 얻을 수 있었다.

• 한국진공학회지
• /
• 제13권3호
• /
• pp.109-113
• /
• 2004

InP에서 열처리 온도와 시간 및 활성화 온도에 따른 Zn의 확산의 특성을 electrochemical capacitance-voltage 법으로 조사하였다. InP층은 metal organic chemical vapor deposition를 이용하여 성장하였으며, 화산방법으로는 $Zn_3P_2$ 확산과 박막과 rapid thermal annealing를 사용하였다. 최대의 정공 농도를 갖는 p-lnP 층은 $550^{\circ}C$에서 5분 동안 확산과 활성화를 한 시료에서 얻었고, Zn의 농도는 $1\times10^{19}\textrm{cm}^{-3}$이었다. $550^{\circ}C$에서 5-20 분 동안 확산을 수행한 결과 정공농도의 확산 깊이는 1.51 $\mu\textrm{m}$에서 3.23 $\mu\textrm{m}$로 이동하였고, Zn의 확산계수는 $5.4\times10^{-11}\textrm{cm}^2$/sec이었다. 활성화 시간의 증가로, Zn가 더 깊게 확산하지만, 정공농도는 거의 변화가 없었다. 이는 도핑된 영역의 과잉의 침입형 Zn가 도핑되지 않은 영역으로 빠르게 확산하고 치환형 Zn로 변한다는 것을 의미한다. 정공농도는 $SiO_2$ 박막의 두께가 1,000$\AA$ 이상이어야 안정적으로 분포된다.

• 한국진공학회지
• /
• 제6권1호
• /
• pp.28-35
• /
• 1997

급속열처리에 따른 (hfac)Cu(VTMS)구리원으로 증착한 구리 박막의 특성개선 효과 와 TiN층의 확산방지 특성의 변화를 고찰하였다. 구리 박막의 특성 변화는 열처리 시간보 다 열처리 온도의 변화에 더 민감하며, 후열처리에 의해 Cu/TiN구조의 전기적 특성과 더불 어 미세구조 변화가 뚜렷하게 나타났다. $400^{\circ}C$이상에서 면저항의 증가가 시작되어 $600^{\circ}C$이 상에서 구리와 TiN의 상호 반응과 구리박막 표면에서의 산화물 형성이 관찰되었다. 후열처 리에 의한 결정립 성장은 (111)배향을 나타내었고, $500^{\circ}C$에서 결정립의 성장이 가장 활발하 게 나타났다. MOCVD-Cu/PVD-TiN구조에서 TiN층의 확산방지 특성을 충분히 유지시키면 서 구리 박막의 전기적 특성을 개선시킬 수 있는 열처리 공정 온도는 $400^{\circ}C$정도가 적정한 것으로 판단되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.316-316
• /
• 2010

Thin films spin-coated from solvent solutions are characterized by solution parameters and spin-coating process. In this study, performance characteristics of polymer solar cells were investigated with changing solution parameters such as solvent and additives. The phase-separation between polymer and fullerene is needed to make the percolation pathway for better transportation of hole and electron in polymer solar cells. For this reason, cooperative effects of solvent mixtures adding additives with distinct solubility have been studied recently. In this study, chlorobezene, 1, 2-dichlorbenzene, and chloroform were used as solvent. 1, 8-diiodoctaned and 1, 8-octanedithiol were used as additives and were added into poly(3-hexylthiophene-2, 5-diyl)/[6, 6]-phenyl C61 butyric acid methyl ester (P3HT/PCBM) blends. Pre-patterned ITO glass was cleaned using ultrasonication in mixed solvent with ethyl alcohol, isopropyl alcohol and acetone. PEDOT:PSS was spin-coated on to the ITO substrate at 3000rpm and was baked at $120^{\circ}C$ for 10min on the hotplate. The prepared solution was spin-coated at 1000rpm and the spin-coated thin film was dried in the Petri dishes. Al electrode was deposited on the thin film by thermal evaporation. The devices were annealed at $120^{\circ}C$ for 30min. By adding 2.5 volume percent of additives into the chlorobenzene from that bulk heterojunction films consisting of P3HT/PCBM, the power efficiency (AM 1.5G conditions) was increased from 2.16% to 2.69% and 3.12% respectively. We have investigated the effect of additives in P3HT/PCBM blends and the film characteristics and the film characteristics including J-V characteristics, absorption, photoluminescence, X-ray diffraction, and atomic force microscopy to mainly depict the morphology control by doping additives.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.89-89
• /
• 2010

The atomic structure of Sb/Si(5 5 12)-$2{\times}1$ surface, deposited at room temperature (RT) and post-annealed, has been identified by scanning tunneling microscopy and the corresponding interface has been studied by synchrotron core-level photoemission spectroscopy. With 0.3-nm Sb deposition at RT and postannealing at $600^{\circ}C$, the surface has been facetted to (225)-$2{\times}1$ and (112)-$1{\times}1$, and its Si 2p has shown that all the Si 2p surface components have disappeared, while the single Sb-Si interfacial component has appeared. Such results indicate that all of surface Si atoms are replaced by Sb atoms and the charge is transferred from Si to passivating Sb-atoms at the top layer. With subsequent postannealing up to $700^{\circ}C$, the surface has been facetted to (113)-$2{\times}2$ and (335)-$4{\times}2$, still having Sb-Si interfacial component and partially re-exposed Si surface components. From the present study, the role of surfactant atom, Sb, as well as the thermal-stabilization of Sb-passivated high-index Si surface will be exposed. Especially, the key role of the Sb/Si(113)-$2{\times}2$, composed of Rebonded-Dimer-Rebonded atom 1D structures, for stabilization will be discussed.