• Geomechanics and Engineering
• /
• 제1권3호
• /
• pp.179-191
• /
• 2009

For a two-way drainage deposit under a surcharge load, it is possible to leave a layer adjacent to the bottom drainage boundary without prefabricated vertical drain (PVD) improvement and achieve approximately the same degree of consolidation as a fully penetrated case. This depth is designated as an optimum PVD installation depth. Further, for a two-way drainage deposit under vacuum pressure, if the PVDs are fully penetrated through the deposit, the vacuum pressure will leak through the bottom drainage boundary. In this case, the PVDs have to be partially penetrated, and there is an optimum installation depth. The equations for calculating these optimum installation depths are presented, and the usefulness of the equations is studied by using finite element analysis as well as laboratory model test results.

• 대한자원환경지질학회:학술대회논문집
• /
• 대한자원환경지질학회 2003년도 춘계 학술발표회 논문집
• /
• pp.19-19
• /
• 2003

Cineam gold deposit is one of an epithermal gold deposit of Low Sulfidation type, which is located in the Sunda-Banda magmatic Arc Zone. Its existence in this region has led to a new concept or few point on the Sunda - Banda Magmatic Arc. Even the deposit is classified as a small scale in mine, however, mineralogically, fluid inclusion and isotopes studies are very interesting to be studied. (omitted)

• 연구논문집
• /
• 통권31호
• /
• pp.127-133
• /
• 2001

In chromium electrodeposition, crack is inevitably accompanied by chromium layer. Behavior of crack formation and crack density were different from the plating conditions such as current density, temperature, waveform of applied current and so on. And cracks have an influence on the corrosion resistance of chromium deposit, because corrosion occurs through the network of cracks between deposit and substrate. Therefore, many researches have been achieved in order to remove the cracks in chromium deposit. Formation of double layers, Cr/Cr and Ni/Cr were investigated to increase corrosion resistance of chromium deposit in this study. As pretreatment prior to outer chromium coating, acid pickling and current control method were examined. Cracks in cross-section of each sample were observed with SEM and CASS(Copper modified acetic acid salt spray) test was performed to evaluate corrosion resistance. It was found that corrosion resistance of Cr/Cr and Ni/Cr double layers were superior to Cr or Ni single layer from the results of CASS test.

• 한국지반신소재학회논문집
• /
• 제16권4호
• /
• pp.103-111
• /
• 2017

사우디 아라비아 해안지역은 사브카 토사로 덮인 매우 넓은 평지구역으로 활용가치가 높지만 소금물로 된 높은 지하수위와 느슨한 밀도, 수분에 취약한 결정체 등의 함유로 갑작스런 침하 등의 문제를 가지고 있어 지지력 향상을 위한 지반개량이 필요하다. 본 연구에서는 사우디 해안지역의 사브카 지반의 특성을 분석하고 동다짐 공법의 적용성을 평가하였다. 수치해석 매개변수분석을 수행하여 동다짐 조건에 따른 사브카 지반의 거동을 분석하고 기존에 제안된 영향깊이 산정법 등이 사브카 지반에 적용이 적절한 지 평가하였으며, 동다짐 공법 적용 시 문제점과 대책에 대하여 논하고자 한다.

• 한국지구과학회지
• /
• 제30권7호
• /
• pp.801-809
• /
• 2009

북부 아르헨티나 후후이주 동부에 위치하는 살리나스그란데스 붕산염(borate) 광상은 플라야 주변부에 배태되는 플라야(playa)형 증발광상이다. 이 광상에서 산출되는 붕산염광물은 주로 울렉사이트(ulexite, $NaCaB_5O_9{\cdot}H_2O$)로 붕소의 주공급원은 주변 화산암일 것으로 추정된다. 아르헨티나 후후이주 동부는 아건조 기후의 알티플라노-푸나 고평원에 위치한다. 중생대 및 신생대 화산암체는 붕소의 주요 공급원으로 생각되며, 플라야는 이들 붕소가 침전되는 주요분지 역할을 하여 이 지역은 붕소의 이동과 침전을 위한 좋은 지형적 지구조적 조건을 보인다. 따라서 향후 이 지역의 붕산염 광체에 대한 지속적인 탐사가 필요 할 것으로 생각된다.

• 동력기계공학회지
• /
• 제5권3호
• /
• pp.88-94
• /
• 2001

Stellite 12 alloy-powders were overlaid on 410 stainless steel valve seat using plasma transferred arc(PTA) process. Variation of the microstructure, hardness, wear and corrosion of overlaid deposit with current change was investigated. The deposit showed hypoeutectic microstructure, which was consisted of primary cobalt dendrite and networked $M_7C_3$ type eutectic carbides. As current increased, the amount of eutectic carbide decreased and its dendritic secondary arm spacing increased. Hardness of the deposit was decreased with increase of current. Stress relief heat treatment at $600^{\circ}C$ for two hours resulted in slight increase of hardness in the deposit and showed uniform hardness distribution in base metal without any hardened layer in HAZ. Specific wear decreased with increase of sliding distance. The deposit of high hardness with a lot of eutectic carbide showed relatively low specific wear. Initial corrosion current density of the deposit in 0.1N sulfuric acid was lower than those of 410 stainless steel, and showed a little variation with PTA current.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.100-106
• /
• 1998

The wide open throttle performance and piston temperatures were measured by the change of fuel : gasoline and liquefied petroleum gas(LPG). Bench test method was developed and experimented to study the effect of temperature on the formation of carbon deposit. The bench test results were confirmed by measuring the piston temperature and observing the deposit production rate at an actual engine running condition. Results show that if the fuel of spark ignition engine is changed from gasoline to LPG, the output power decreases about 10% and the piston temperatures increase about 40~55$^{\circ}C$. In actual engine tests, because of this temperature increase, it was observed that the quantity of carbon deposit in the top ring groove increased in a big degree. Consuquently, it is known that the fing sticking may occur if the gasoline engine was rebuilt to LPG fuelled engine. Therefore, in order to preserve the durability of LPG fuelled engine, it is necessary to lower the piston temperature by hardware modificationor to reduce the carbon deposit by the improvement of engine oil.

• 한국환경과학회지
• /
• 제12권2호
• /
• pp.227-236
• /
• 2003

Electrokinetic remediation technique offers the opportunity to extract heavy metals from soils with high plasticity. The experiment demonstrated the applicability of electrokinetic remediation on metal-mining deposit and the decision of the enhancement method for four kinds of bench-scale studies. According to the sequential extraction of heavy metals in the "I" mining deposit, Pb and Cu were mostly associated with residual fraction and Zn and Cd were associated with water soluble and residual fraction. Therefore, removable fractions by electrokinetic technology was determined by the sum of the fraction of water soluble and exchangeable, which is Cu : 19.53%, Pb : 1.42%, Cd : 52.82%, Zn : 57.28%, respectively. When considering electrical potential, volume of effluent, soil pH, and eliminated rate of contaminant, results determined by sum of each weight were Citric aic+SDS (13) > 0.1N $HNO_3$ (10) > HAc (8) > DDW (4). Therefore, citric acid and SDS mixed solution was determined the best enhancing agent for the remediation of metal mining deposit.g deposit.

• 한국수산과학회지
• /
• 제28권6호
• /
• pp.793-804
• /
• 1995

Polychaetous community survey in Tomioka Bay was carried out 5 times seasonally from May 1991 to March 1992 by quantitative grab sampling (0.05m2) at 11 stations. Based on the granulometric composition and environmental factors, a homogeneous soft bottom was found in St.5-10. The species of the polychaete were classified into three feeding groups using the Fauchald and Jumars' feeding guild system. According to polychaetous community composition data, deposit feeders predominate in sandy silt area where the silt-clay content is $60-69.3\%.$ These deposit feeders were subdivided into surface deposit feeders and subsurface deposit feeders by their living position and mode. Also, suspension feeding group comes as the third dominant group. Seasonal changes of each feeding group were described in terms of numerical density and biomass. Feeding layer and types of dominant species (Lumbrineris longifolia: surface deposit feeder; Praxillella pacifica: subsurface deposit feeder; Chone duneri; suspension filter feeder, etc.) were examined in the intact sediment core samples. Also, longterm density change among the three dominant species during 10 years was disussed.

• 정보관리학회지
• /
• 제25권4호
• /
• pp.5-23
• /
• 2008

국립중앙도서관에서 인쇄 출판물을 대상으로 운영 중인 납본체계와는 달리 웹 아카이빙인 OASIS (Online Archiving & Searching Internet Sources)는 웹 사이트, 웹 자원 등의 온라인 디지털 자원을 대상으로 자원 수집, 관리 및 보존하기 위한 과정이 필요하다. 이에 본 논문에서는 웹 아카이빙을 위한 디지털 자원 납본 프로세스를 개발하기 위해 디지털 자원 납본 주체와 대상을 정의하였고, 납본프로세스를 위한 단계별 정의와 기능을 명시하였다. 또한 디지털 납본 시스템 구성을 위한 업무 흐름도와 단위 업무에 따른 기능 정의와 정보 흐름을 위한 구조를 제시하였다.