• Journal of the Optical Society of Korea
• /
• v.16 no.2
• /
• pp.181-184
• /
• 2012

We report, for the first time, operation frequency dependence of current density-voltage ($J_{OLED}-V_{OLED}$) shift for multi-layer organic light-emitting diodes (OLEDs). When the OLEDs were electrically stressed for 21 hours with 50% duty voltage pulses at 60, 120, 240, and 360 Hz, the JOLED-VOLED shifts were suppressed by half for 360 Hz operation compared with 60 Hz operation, but with little change in emission efficiencies. This frequency dependent $J_{OLED}-V_{OLED}$ shift is believed to be commonly observed for typical multi-layer OLEDs and can be used to further improve lifetime of digitally-driven active-matrix OLED displays.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.701-709
• /
• 2002

Aluminium foam material is highly porous material, which has the complicated cellular structure defined by randomly distributed pores in metallic matrix. This structure gives the characteristic properties which cannot be achieved by any other conventional processes. As the properties of aluminium foam material significantly depend on its porosity, a desired profile of properties can be tailored by changing the foam density. But various defects lead to undesirable effects on the mechanical properties. Mechanical properties are dependent on cell sizes and aspect ratios. Therefore, this paper presents the effects of various processing parameters of various parameters on the mechanical properties. For the sake of this, combined stirring was used to fabricate aluminum foam materials by the parameters. Compression and bending tests were performed to investigate the effects of cell sizes and aspect ratios on the mechanical properties.

• Journal of Electrochemical Science and Technology
• /
• v.1 no.2
• /
• pp.69-74
• /
• 2010

Methodologies to improve photovoltaic performance of dye-sensitized solar cell (DSSC) are reviewed. DSSC is usually composed of a dye-adsorbed $TiO_2$ photoanode, a tri-iodide/iodide redox electrolyte and a Pt counter electrode. Among the photovoltaic parameters of short-circuit photocurrent density, open-circuit voltage and fill factor, short-circuit photocurrent density is the collective measure of light harvesting, charge separation and charge collection efficiencies. Internal quantum efficiency is known to reach almost 100%, which indicates that charge separation occurs without loss by recombination. Thus, light harvesting efficiency plays an important role in improvement of photocurrent. In this paper, technologies to improve light harvesting efficiency, including surface area improvement by nano-dispersion, size-dependent light scattering efficiency, bi-functional nano material, panchromatic absorption by selective positioning of three different dyes and transparent conductive oxide (TCO)-less DSSC, are introduced.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.8-11
• /
• 2007

The new technologies in mobile display developed in SEC are briefly reviewed. For a differentiation, SEC's LTPS line is based on SLS (Sequential Lateral Solidification) technology. In this paper, the characteristics of SEC's SLS in recent and future mobile displays were discussed. The microstructure produced by SLS crystallization is dependent on SLS process conditions such as mask design, laser energy density, and pulse duration time. The microstructure and TFT (Thin Film Transistor) performance are closely related. For an optimization of TFT performance, SLS process condition should be adjusted. Other fabrication processes except crystallization such as blocking layer, gate insulator deposition and cleaning also affect TFT performance. Optimized process condition and tailoring mask design can make it possible to produce high quality AMOLED devices. The TFT non-uniformity caused by laser energy density fluctuation could be successfully diminished by mixing technology.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1739-1741
• /
• 2000

DC current density-voltage and impedance spectroscopy studies have been performed on indium-tin-oxide(ITO)/para-sexiphenyl(6p)/aluminium organic electroluminescent device. The device exhibited a blue color emission, The turn-on voltage of the device is observed at 5V from the current density-voltage measurements. The impedance spectroscopy measurements show that a resonance frequency shift with applied DC bias is observed and a single semi-circle Cole-Cole plot is confirmed. The bias-dependent bulk resistance and bias-independent bulk capacitance is observed.

• 전기의세계
• /
• v.28 no.9
• /
• pp.43-50
• /
• 1979

Silicon nitride films were chemically deposited on silicon substrates by reacting SiCl$_{4}$ and NH$_{3}$ in a nitrogen atmosphere at 700~1100 .deg.C. The deposition rate increased rapidly with deposition temperature upto about 1000 .deg.C, and became less temperature dependent above this temperature. The etch rate of films in buffered HF solution decreased, with an increase of deposition temperature, and a heat treatment at a temperature higher than that of the deposition considerably reduced the etch rate. It indicates that the heat treatment resulted in a densification of the films. Surface charge density of 3~4 * 10$^{11}$ /cm$^{2}$ was determined from the C-V characteristics of MNS diode, and it was also found that surface charge density depended on deposition temperature, but not film thickness. The current-voltage characteristics displayed a logI-V$^{1}$2/ dependence in the temperature range of 300~500.deg.K. Measurement of the slope of this characteristics and its dependence on temperature and bias polarity suggest that conduction in sili con nitride films arises from the Poole-Frenkel mechanism.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.29-32
• /
• 2000

In this paper, an analytical model for I-V characteristics of a HEMTs is Proposed. The developed model takes into account the temperature dependence of drain current. In high-speed ICs for optical communication systems and mobile communication systems, temperature variation affects performance; for example the gain, efficiency in analog circuits and the delay time, power consumption and noise mrgin in digital circuits. To design such a circuit taking into account the temperature dependence of the current-voltage characteristic is indispensible. This model based on the analytical relation between surface carrier density and Fermi potential including temperature dependent coefficients.

• 한국전기화학회:학술대회논문집
• /
• 2004.06a
• /
• pp.287-292
• /
• 2004

In order to understand the relationship between molecular structure of Metal-Organic Framework(MOF) and capacity of hydrogen absorption, quantum mechanical calculations and grand canonical Monte Carlo simulations have been carried out on a series of MOF-5 having various organic linkers. The calculation results about specific surface area and electron density for various frameworks indicated that the capacity of the hydrogen storage is largely dependent on effective surface area rather than the free volume. Based on the iso-electrostatic potential surface from density functional calculation and the amount of adsorbed hydrogens from grand canonical Monte Carlo calculation, it was also found that the electron localization ground organic linker plays an important role in hydrogen capacity of MOFs.

• Journal of Sensor Science and Technology
• /
• v.18 no.3
• /
• pp.226-233
• /
• 2009

In this study, the optical properties of localized surface plasmon resonance sensor using optical fiber was analyzed as the variation of a size and surface density of gold nano particles on the etched optical fiber surface. It is shown that a size and surface density of gold nano particles on optical fiber surface are controlled by $Na_3$ citrate quantity and pH of gold colloid solution. To measure the sensitivity, peak wavelength of absorbance spectrum was detected as the reflective index of the solution. The sensor sensitivity is linearly dependent on the size and surface densities of gold nano particles from the results of optical experiments.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.529-530
• /
• 2006

This paper concerned with SPS (spark plasma sintering), hot pressing of sinter nanometer WC-Co powder and discussed the density, hardness, microstructures and grain sizes of the alloys sintered. The results showed that the two sintered techniques could produce high density alloys and play well on the grain growth, but SPS could lower the sintering temperature and shorten sintering time. Besides, the hardness of the sintered cemented alloys that was dependent on the grain size and densification could also be improved.