• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.5
• /
• pp.67-76
• /
• 2013

In this study, the inhibitive effect of electrochemical treatment subjected to fresh and hardened concrete and literature reviews in terms of the treatment were performed. In hardened concrete, chloride ions are mixed during casting to destroy the passivity of steel, and then the current was provided for 2 weeks with 250, 500 and $750mA/m^2$. After completion of electrochemical treatment, the extraction of chloride ions was quantified and repassivation of steel was observed. Simultaneously, the equated levels of current density for 2 weeks were applied to fresh concrete. Steel-concrete interface in concrete was observed by BSE image analysis and the concrete properties in terms of the diffusivity of chloride ions and the resistance of steel corrosion was measured. As the result, electrochemical treatment is very effectiveness to rehabilitate the passive film on the steel surface and 63-73% of chloride ions in concrete were extracted by the treatment. As the treatment was applied to fresh concrete, the resistance of steel corrosion was improved due to the densification of $Ca(OH)_2$ layers in the vicinity of steel. However, an increase in the current density resulted in an increase in surface chloride content of concrete.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.6 no.2
• /
• pp.119-128
• /
• 2008

Thermal assessment of a new CANDU spent fuel disposal system, which improves the retrievability of the spent fuel and enhances the densification factor compared with the Korean Reference disposal System, is carried out in this study. The canisters for CANDU spent fuels are stored for long term and cooled by natural convection in the proposed disposal system for the retrievability. The steady state thermal analyses for proposed CANDU disposal system are carried out with the ANSYS 10.0 CFX code. The thermal analyses are performed through two steps. At the first step, the sensitivity of the disposal tunnel spacing is analysed. The differences of maximum temperatures by several tunnel spacings are calculated at three points in the disposal tunnel. The result shows that the differences of the temperature at the three points are almost negligible because 99% of the decay heat is removed by natural convection. At the second procedure, 60m tunnel spacing with a ventilation system instead of natural convection is considered. The result is applied to the calculation of the canister surface temperature in disposal tunnel as boundary conditions. Consequently, the average and the maximum surface temperature of disposal canisters are $79.9^{\circ}C$ and $119^{\circ}C$, respectively. The inner maximum temperature of a basket in the disposal canister is calculated as $140.9^{\circ}C$. The maximum temperature of the basket meets the thermal requirement for the CANDU spent fuel cladding.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.11
• /
• pp.878-885
• /
• 2012

In this study we aims to examine the co-doping effects of 1/3 mol% $Mn_3O_4+Co_3O_4$ (1:1) on the reaction, microstructure, and electrical properties such as the bulk defects and grain boundary properties of $ZnO-Bi_2O_3-Sb_2O_3$ (ZBS; Sb/Bi=0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Mn,Co-doped ZBS, ZBS(MCo) varistors were controlled by Sb/Bi ratio. Pyrochlore ($Zn_2Bi_3Sb_3O_{14}$) was decomposed and promoted densification at lower temperature on heating in Sb/Bi=1.0 by Mn rather than Co. Pyrochlore on cooling was reproduced in all systems however, spinel (${\alpha}$- or ${\beta}$-polymorph) did not formed in Sb/Bi=0.5. More homogeneous microstructure was obtained in $Sb/Bi{\geq}1.0$ In ZBS(MCo), the varistor characteristics were improved drastically (non-linear coefficient, ${\alpha}$=30~49), and seemed to form $Zn_i^{..}$(0.17 eV) and $V_o^{\bullet}$(0.33 eV) as dominant defects. From impedance and modulus spectroscopy (IS & MS), the grain boundaries have divided into two types, i.e. the one is tentatively assign to $ZnO/Bi_2O_3(Mn,Co)/ZnO$ (0.47 eV) and the other ZnO/ZnO (0.80~0.89 eV) homojunctions.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.258-265
• /
• 2014

By replacing the previous metal connector on the joints of timber structure, the GFRP reinforced laminated wooden pin was produced using a wooden material and Glass fiber reinforced plastic(GFRP) composite laminate. In addition, using the reinforced wooden pin, the tensile type shear strength test was conducted. Based on the result of the bending strength test of the reinforced laminated wooden pin according to the GFRP arrangement, a specimen(Type-A) with a single insertion of GFRP for each layer have shown the most favorable performance. Also, it was verified that densified specimen hot pressed for an hour at the temperature of $150^{\circ}C$ and with the oppression pressure $1.96N/mm^2$ have shown the improved performance of 1.57 times than the specimen without the densification. And in the bending strength test considering the load direction, edgewise have shown a higher performance of 3.51 times than the flatwise. A shear strength test was conducted using the Type-A reinforced laminated wooden pin which have shown a moderate performance on the test. Based on the test conducted by differentiating the type of the joint plate and the connector, compared to the specimen(Type-DS) applied with the drift pin and steel plate, the specimen( Type-WL) applied with the GFRP reinforced laminated wooden pin and GFRP reinforced wooden laminated plate have shown 1.12 times higher shear strength and also have shown an excellent toughness even after the maximum load.

• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.775-782
• /
• 1994

Influence of $TiO_{2}$ addition on sintering behavior and microstructure of MgO-$ZrO_{2}$ composites was studied. $ZrO_{2}$ containing 3mol%Y203 was existed as a c-$ZrO_{2}$ phase due to the formation of solubility of MgO, $TiO_{2}$ and $ZrO_{2}$ when sintered $1400^{\circ}C$ for 2h. All the compositions employed exhibited a similar shrinkage behavior with an end-point shrinkage between 8.58 and 11.00%. The additlon of $TiO_{2}$ promoted densification and the bulk density of specimen containing 1.67wt% $TiO_{2}$ was 3.75g/$\textrm{cm}^3$(98% TD) when $1600^{\circ}C$ for 2h. The amount of solubilities of MgO and TiOz in $ZrO_{2}$ were 5.ti7wt% and 2.62wt%,respectively. They were partially segregated near $ZrO_{2}$ grain boundary in the form of Ti-compounds during cooling. This segregation resulted in the formation microcracks which decreased the bending strength.

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1245-1251
• /
• 1999

Phase-change optical disk very rapid recording, high densification of data, resulting in high feedback rate and good C/N(carrier to noise) ratio of a feedback signal. However, repetitive thermal energy may cause the deformation of a disk or the lowering of an eliminability and a cyclability of the recording. The lowering of the cyclability can be reduced by insertion of thin layer of ZnS-$SiO_2$ dielectric thin film in appropriate disk structure between the upper and lower part of the recording film. Using the Taguchi method, optimum conditions satisfying both the optimized quality characteristic values and the scattering values for film formation were found to be the target R.F. power of 200W, the substrate R.F. power of 20W, the Ar pressure of 6mTorr, and the electrode distance of 6cm. From the refractive index data, the existence of the strong interaction between the electrode distance and Ar pressure was confirmed, and so was the large effect of the electrode distance on transmittance. According to the analysis of TEM and XRD, the closer the electrode distance was, the finer was the grain size due to the high deposition rate. However, the closer electrode distance brought the negative effect on the morphology of the film and caused the reduction of transmittance. AFM and SEM analyses showed that the closer the electrode distance was, the worse was the morphology due to the high rate of the deposition. Under optimum condition, the deposited thin film showed a good morphology and dense microstructure with less defects.

• Applied Chemistry for Engineering
• /
• v.32 no.5
• /
• pp.569-573
• /
• 2021

In this study, high-density carbon blocks were manufactured using coke, binder pitch, and impregnated pitch, then the effect of pitch fluidity on the densification of carbon blocks during the impregnation process was investigated. A green block was manufactured through high-pressure figuration of coke and binder pitch, and a carbon block was obtained through a heat treatment process. An impregnation process was performed to remove pores generated by volatilization of the binder pitch during the heat treatment process. The impregnation process was carried out the high-pressure reaction step of impregnating the pitch into the carbon block followed by the pretreatment step of melting the impregnation pitch. Melting of the impregnation pitch was carried out at 140~200 ℃, and the viscosity of the impregnation pitch decreased as the heat treatment temperature increased. The decrease in the viscosity of the impregnation pitch improved the fluidity and effectively impregnated the pores inside the carbon block, reducing the porosity of the carbon block by 83% and increasing the apparent density by 5%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.2
• /
• pp.61-70
• /
• 2019

Geopolymer is an eco-friendly construction material that has various advantages such as reduced $CO_2$ emission, fire resistance and low thermal conductivity compared to cement. However, it has not been many studies on the thermal behavior of the surface of the geopolymer panel when flame is applied to the surface. In this study, surface characteristics of hardened geopolymer on flame exposure was investigated to observe its characteristics as heat-resistant architectural materials. External structure changes and crack due to the heat shock were not observed during the exposure on flame. According to the residue of calcite and halo pattern of aluminosilicate gel, decarboxylation and dehydration were extremely limited to the surface and, therefore, it is thought that durability of hardened geopolymer was sustained. Gehlenite and calcium silicate portion was inversely proportional to quartz and calcite and significantly directly proportional to BFS replacement ratio. Microstructure changes due to the thermal shock caused decarboxylation and dehydration of crystallization and it was developed the pore and new crystalline phase like calcium silicate and gehlenite. It is thought that those crystalline phase worked as a densification and strengthening mechanism on geopolymer panel surface.