• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.166-169
• /
• 2004

NDVI has been used to estimate several ecological variables including leaf area index (LAI). Global MODIS LAI data are partially produced by empirical model that is based on the assumption of high correlation between NDVI and LAI. This study attempts to evaluate the MODIS empirical model by comparing with the result obtained from field LAI measurement and Landsat ETM+ reflectance. MODIS LAI product and ancillary data were analyzed over a small forest watershed near the Seoul metropolitan area. The relationship between NDVI of ETM+ and field measured LAI did not correspond to MODIS LAI estimation. Since the study area is mostly covered by very dense and fully closed forest, the correlation between NDVI and LAI might not be high. Although MODIS LAI product has great potential for global environment studies, it needs to be cautious to use them in regional and local area in particular for the forest of dense canopy situation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.842-845
• /
• 2000

The purpose of this paper is to investigate the influences on mechanical properties of motor pistons manufactured by casting, conventional forging and powder forging, using the comparison of characteristics like microstructure, hardness, tensile strength, and elongation. To form conventional forging piston, the experiment of visioplasticity was performed. As the model material, plasticine was used. To form powder forging piston, the shape of piston was simplified as simple cup shape. Material properties like workability, density variation before and after forging, and strain loci of material during forging were investigated. Powder forging and conventional forging technologies were effective to gain dense microstructure. In powder forging, distribution of such dense microstructuer was uniform. For hardness, pistons from powder forging and conventional forging technologies were much better than that from casting. For tensile strength and elongation, powder forging and conventional forging technologies were also advantageous.

• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1169-1175
• /
• 1994

Five Al2O3/SiC/metal composites with four different particle sizes of green SiC abrasive grains are grown by the directed oxidation of an commercially available Al-alloy. Oxidation was conducted in air at 100$0^{\circ}C$, 96 hours long. Slip casted SiC-fillers were placed on the alloy or SiC powder deposited up to the required layer thickness. Their microstructures are described and measurements of density, elastic constants, frexural strength, fracture toughness and work of fracture are reported. The results are compared with those of commercial dense sintered Al2O3. The properties of produced materials have a strong relationship to not only the properties of Al2O3, SiC, Al and Si but also to the phase share and phase distribution. The composite materials are dense (0.5% porosity), tough (KIC = 3.4~6.4 MPa{{{{ SQRT { m} }}), strong ({{{{ sigma }}B = 170~345 MPa) and reasonably shrinkage free producible. The reinforcements is attained mainly through the plastic deformation of ductile metal phase.

• Journal of the Korean Ceramic Society
• /
• v.36 no.9
• /
• pp.991-996
• /
• 1999

Effect of solution property on the weight varation and microstructural change of film was studied by electrophoretic deposition in order to obtain a homogeneous and dense zirconia film. As a result of weight kinetics of film which obtained in alcohol or aqueous solution having different polarity experimental data showed large deviation from theoretical ones calculated by Zhang's kinetic model. It had been shown that the weight affecting factors was largely dependent on properties other than dielectric constant and viscosity of solvent zeta potential appiled field and time. In initial stage a main factor of the drastic weight increase was the capillary drag of porous substrate. The cause of weight decrease with time in aqueous solution after 300 s was attributed to the defect of film by sagging and electrolytic reaction. The electrolyte film which prepared in alcohol solution with good wetting for substrate had better homogeneous and dense microstructure than one in aqueous solution with high surface tension.

• Journal of the Korean Ceramic Society
• /
• v.45 no.10
• /
• pp.594-599
• /
• 2008

Hydroxyapatite(HA) was prepared from waste tuna bone, and its sintering property and dissolution behavior were investigated. Tuna bone derived-HA powder consisted of mainly HA and small amount of MgO. Porous HA ceramics with sintered density of 79% was obtained by pressureless sintering at $1200^{\circ}C$. Meanwhile, HA ceramics prepared by hot pressing at $1000^{\circ}C$ showed dense microstructure with sintered density of 95%. Immersion test revealed that both porous and dense HA ceramics were stable in liquid environment without distinct evidence of surface dissolution. It may be assumed that the presence of Mg in tuna bone-derived HA may improve dissolution resistance of HA.

• Journal of the Korean Ceramic Society
• /
• v.47 no.1
• /
• pp.71-74
• /
• 2010

We have investigated protonic conduction in highly dense (>98%) polycrystalline Y-doepd $BaZrO_3$ (BYZ) ceramic with an average grain size of ~85 nm. It is observed that the protonic conductivity across the grain boundaries in this nano-crystallilne BYZ (n-BYZ) is significantly higher than the microcrystalline counterpart. Such a remarkable enhancement in grain boundary conductivity results in high overall conductivity that may allow this chemically stable protonic conductor to serve as a solid electrolyte for low-temperature solid oxide fuel cell applications.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.6
• /
• pp.249-252
• /
• 2010

The ground amorphous powder was consolidated into a dense sintered body with a typical ultrafine $Al_2O_3-GdAlO_3$ eutectic structure by spark plasma sintering (SPS). Sintered material with ultrafine and dense eutectic structure was obtained by an appropriate combination of rapid quenching and SPS at lower temperature and more quickly than by conventional sintering. The $Al_2O_3$-based rare earth eutectic ceramics for solar cell emitters are believed to have a higher efficiency and the $Al_2O_3$ based eutectic ceramics with ultrafine grains will be one of the promising materials showing excellent selective emitter characteristics.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.1
• /
• pp.41-44
• /
• 2014

We employed UV-Ozone treatment method for the fabrication of dense and highly conductive nanoparticle thin films. We demonstrated the UV-Ozone treatment effect on the silver nanoparticle thin films as a function of time and temperature. The capping layers of nanoparticles were decomposed after UV-Ozone treatment and dense nanoparticle thin films were obtained. Moreover, electrical and mechanical properties of the thin films after UV-Ozone treatment were measured by using resistance measurements under tension in an in-situ tensile tester. The initial resistance of nanoparticle thin films was decreased by 82.6% with optimized UV-Ozone treatment condition of $150^{\circ}C$ for 20 minutes.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.642-647
• /
• 2003

Palladium is widely used for several applications and recovery of palladium from secondary sources becomes increasingly important since palladium is one of maldistributed platinum group metals. Electrochemical recovery of dense palladium metal sheet from Pd leaching solution is a simple and easily controlled method. The surface morphology of the recovered Pd metal was significantly affected by current density and temperature. Dense deposit morphology was in higher stress state regardless of preparation condition under $55^{\circ}C$. Rising temperature up to $70^{\circ}C$ had a stress releasing effect besides densification of Pd deposit.

• Applied Microscopy
• /
• v.25 no.4
• /
• pp.115-123
• /
• 1995

This study was carried out to observe the functional ultrastructures of photoreceptor cells in frog(Rana catesbeiana) retina using transmission electron microscope. The photoreceptor cells are divided into two types-rod and cone cells-consist of outer and inner segment. The long outer segment of rod cell contains dense stacks of membrane and formed vertical and horizontal folds. The outer segment of cone cell is small, and vertical and horizontal folds are not exist. The electron dense cytoplasm of rod cell contains compact mitochondria, Golgi complexes, and endoplasmic reticula. The inner segment of cone cell shows low electron density and contains a large lipid droplet in the upper part of inner segment. In addition, cone cell contains many mitochondria, Golgi complexes. rough endoplasmic reticula, ribosomes and numerous glycogen particles. It is believed that these ultrastructural characteristics are closely associated with photoreceptive function of photoreceptor cells in frog retina.