• Journal of Sericultural and Entomological Science
• /
• v.25 no.1
• /
• pp.44-50
• /
• 1983

The study was carried out to suggest on opinion of the standardization of size deviation in the existing raw silk testing method. 1. The present grade A of size deviation stipulates 4.61 to 5.80 of standard deviation for 50 to 69 denier of mean value, however, the 5.80 standard deviation with the mean values of 50 and 69 denier belong to different distribution. 2. It is reasonable that the variation coefficients of grade 2A should be lower than that of grade A. However, the present testing method shows larger variation in grade 2A than in grade A. This is illustrated 9.00 for 69 denier in grade 2A and 8.41 for 70 denier in grade A. 3. The size deviation value compares the quality of raw silk with different mean value. Therefore, the standard deviation is recommended to be replaced by the C.V. value in determining the grade of silk. 4. The C.V. have a tendency to increase with lower grades below 6A for the size deviation below 33 denier with some inconsistencies. The figures should be adjusted so that the C.V. inconsistencies size deviation below 33 denier will be corrected. 5. The standard deviation increases with size under the same grade for the size deviations above 33 denier, however, the C.V. does not vary greatly with size deviation. 6. To rectify the above-mentioned inconsistencies the C.V. conversion and curvilinear regresion correction is recommended to improve the present silk testing method 7. The table of size deviation standard are as follows: Suggested standard of size deviation, unit: C.V. Value

• Journal of the Korean Society of Tobacco Science
• /
• v.5 no.2
• /
• pp.77-82
• /
• 1983

The ventilation of cigarette samples made by the combination of various acetate tow denier and porous plug wrapping paper have been investigated The ventilation rate increased no longer in the acetate tow with high mono denier and low total denier but changed slightly in that with low mono denier and high total denier when the porosity of plug wrapping paper was more than 6500cm/min. cbar. Tip pressure drop ratio, Y, was significantly influenced by tip ventilation rate, X. i. e., Y = 1.0880-0.0042x The relationships of ventilation rate, $X_v$. and smoke delivery, Y, were as follows; Tar : $Y_r$= -14.0458-0.1650$X_v$ Nicotine : $Y_N$= - 1.1045-0.0125$X_v$ CO : $Y_{co}$=17.2806-0.2090$X_v$

• Journal of Fashion Business
• /
• v.10 no.3
• /
• pp.23-30
• /
• 2006

Various high-touch textile products have been developed recently including ultra-fine denier filament yarn fabrics. The touch or hand of high value-added products is of prime importance. Physical and mechanical properties of fabric specimens, ultra-fine denier filament yarn fabric specimen, 100% wool fabric and wool/polyester 50:50 fabric,were measured using the KES. Compressibility of the ultra-fine denier fabric is recommendable, possibly due to the good bulk property of the specimen. Overall, the THV of the ultra-fine denier fabric is positioned between those of the 100% wool fabric and wool/polyester 50:50 fabric. Observed differences in the physical and mechanical properties explain the fabric specimen characteristics reasonably.

• Textile Coloration and Finishing
• /
• v.25 no.4
• /
• pp.303-313
• /
• 2013

Alkali hydrolysis of sea-island PET 0.02denier microfiber were compared to those on the fabrics of the 0.06denier microfiber. In the dissolution of the sea component out of sea island type ultra-microfiber, it is important to determine the optimum division and divided material. Weight reduction of sea island ultra-micro sea island fiber was faster than regular PET about 10 times. Also 0.2denier sea-island ultra-micro sea island fiber has better color fastness (washing, friction, and daylight) than 0.06denier level sea-island ultra-microfiber. In this study, 0.2denier ultra-micro sea island fiber shows the possibility of high value product.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.10a
• /
• pp.145-146
• /
• 2008

This is studies about light and thin PET fabric having downproof properties using low denier filament yarn. We study how the manufacturing fabric effect on downproof properties according to conditions of low denier yarn, fabricataion, and dyeing and finishing.

• Journal of Sericultural and Entomological Science
• /
• v.3
• /
• pp.61-67
• /
• 1963

This report is prepared to find how the filament of cocoon bave size deviation relates with the raw silk made by them which are intensively cultured in this country. Three recommended hybrid varieties and two varieties under working at Suwon Sericultural Experiment Station were selected as specimens. The cocoons were reeled as an individual filament of every fifty meters long skein with a wrap reel to weigh the denier and to investigate the relationship of the above statement so that it may be used for the quality estimation before processing it into raw silk. The conclusions obtained are as follows. (1) The variation of Pk${\times}$Sn was found as best cocoon for 21 denier raw silk use, but the number of cocoon to make the denier has to be eight which might cause more labor cost. (2) Baektoo-Kumkang and Myohiang-Chongchon were found as economical varieties for 21 denier use. (3) Seulak-Soyang is a proper variety for the use of 14 or 28 denier silk use. (4) Myohiang-Chongchon did not confirm a good property from the aspect of denier deviation. (5) It was found that there was a fairly strong corelationship between the mean cocoon bave size deviation as indicated by Ono's report. (6) Three graphs were prepared to estimate the cocoon quality before processing into various sizes of raw silk using the mean cocoon bave size and the raw silk size to be prepared. (7) Mean time, the graph which is able to estimate the expectable grade of the raw silk size deviation was designed for the practical use. (8) The expectable grade of the varieties used in this report were found as following data. Notice (A......cocoon number to make raw silk (B......total cocoon bave size deviation (C......expectable silk grade (9) The result of the work concerning the expectable denier deviation on 21 denier silk was the same with the statistical actual testing result as 1.25 D while the distribution showed farther necessity of improvement in technically.

• Fashion & Textile Research Journal
• /
• v.16 no.6
• /
• pp.1008-1016
• /
• 2014

This study aims to analyze the changes in the mechanical properties of woven fabrics(cotton, linen, wool, silk, and polyester) by bonding fusible interlinings with varying deniers(10D, 20D, and 30D) for a 3D virtual try-on system(one that a user to try garments through screens using Avatar) developed over the last decade. We experimented with four mechanical properties and thicknesses of twenty-three specimens of interlining bonded fabrics including face fabrics and interlinings by using the KES-FB-AUTO system. The results showed that the tensile property increased(LT and RT increased and WT decreased) as the denier of the interlining increased; however, the change was slight. In contrast, the bending and shear properties increased significantly as the denier of the interlining increased on both the warp and the weft. This showed evidence that the interlining gives the fabrics size stability. The compression property was slight changed as the tensile property varies depending on the fibers and the denier of interlining. As expected, the thickness increased by bonding the interlining as the denier of interlining increased. From these results, we conclude that 3D users need to reflect these changes of woven fabrics by bonding interlinings when they try screen fittings to accurately express the fabric reality of manufactured garment.

• Journal of Fashion Business
• /
• v.13 no.1
• /
• pp.82-90
• /
• 2009

This research was made to manufacture the fabric for interior uses by spinning a low melting mono 4 denier PET staple fiber with a soluble 1.4 denier fine PET fiber. The blended yarn has a thickness ranging from 10's to 14's, and the soluble PET fine fiber was dissolved to make a pore in the polymer. Thereby a snap property was decreased and a resilience property was improved to be suitable for a functional synthetic leather. In order to attain the optimum condition, a mechanical property according to fineness, and mixing ratio of low melting polymer, warp density, weft density and blending ratio, and a heat contraction ratio according to blending ratio were experimented. The warp density, 220 T/inch of fine denier PET and the weft density, 64 T/inch of thick denier PET were generated to 4/4 both twill weave fabric having constant tensile property and thickness.

• Textile Coloration and Finishing
• /
• v.33 no.4
• /
• pp.269-279
• /
• 2021

In this study, the laminating of TPU film after coating of primer adhesive on the fabrics was applied in order to secure the strength to withstand a fall from a higher altitude by increasing the adhesion between the fabric and the film layer. It seems that the fineness of the yarn and the weave construction have a greater effect than the type of the laminating films. The order of superiority of the laminated fabrics by film type and thickness was the same for 1000 denier and 210 denier fabrics, and the tendency was consistent with the order of superiority in the film properties and peel strength tests. The tear strength of laminating fabrics increased three to four times for 1000 denier fabrics compared to the fabric alone, but it decreased by 2 times for the 210 denier fabrics. Summarizing the above results, it is most appropriate to combine 1000d fabric with three types of laminating films(100~200㎛ thickness) of A(0.2T) or B(0.15T) or D(0.1T) considering the air pressure resistance, the impact resistance during the fall, and the durability against damage during use.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.19 no.1
• /
• pp.187-192
• /
• 2009

Silk filament progression study applying backcross breeding with recipient parent Jata and donor parent Daba ecoraces of tropical tasar silkworm, Antheraea mylitta Drury conducted during 2006 to 2008, revealed introgression of filament denier (10.2 d) superior to both parents at BC4 level. Also, the silk waste (0.35%) and filament breaks (2.6 nos) were reduced compared to both parents, while the filament length (973 m) and non break filament (296 m) improved over donor and could attain closer to recipient parent. The best performance of Jata $\times$ Daba at F1 level, with highest silk filament length (1646 m) of 12.5 d denier, denotes heterosis impact on silk trait with parental heterogenousity, an advantage to exploit silk filament yield. The progression of quality in terms of finer filament denier, less silk waste and least number of filament breaks over both parents and improvement in filament length and non break filament over donor parent except for a marginal shortage against recipient at BC4 level indicates the prospects of Jata and Daba ecoraces as source of breeding material for qualitative improvement of tasar silk filament. The study suggests that the commercially important finer denier of tasar silk filament can be attained with minor reduction in silk yield of wild Jata ecorace by adopting repeated backcrossing for four generations with semi domesticated Daba ecorace.