• Journal of the Korea Society for Simulation
• /
• v.3 no.1
• /
• pp.89-98
• /
• 1994

In this paper, a criteria for selecting an appropriate load redistribution algorithm is devised so that a fault-tolerance distributed system can operte at its optimal efficience. To present the guideline for selecting redistributing algorithms, simulation models of fault-tolerant system including redistribution algorithms are developed using SLAM II. The job arrival rate, service rate, failure and repair rate of nodes, and communication delay time due to load migration are used as parameters of simulation. The result of simulation shows that the job arrival rate and the failure rate of nodes are not deciding factors in affecting the relative efficiency of algorithms. Algorithm B shows relatively a consistent performance under various environments, although its performance is between those of other algorithms. If the communication delay time is longer than average job processing time, the performance of algorithm B is better than others. If the repair rate is relatively small or communication delay time is longer than service time, algorithm A leads to good performance. But in opposite environments, algorithm C is superior to other algorithms.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.1
• /
• pp.43-53
• /
• 1997

A robust stability condition for linear systems with time delay in all variables and parameter uncertainties in all system matrices is derived. Robust performance condition that accounts for robust model-matching of closed loop system and disturbance rejection is also derived. Using the robust performance condition, robust $H^{\infty}$ controller and .mu.(sgructured singular value) controller with two-degree-of-freedom(2DOF) are designed. The controller structure is considered for $H^{\infty}$ controller, while uncertainity structure is considered for .mu. controller. Using the proposed method, $H^{\infty}$ and .mu. controllers for underwater vehicle with time delay and parameter variations are designed. Simulations of a design example with hydrodynamic parameter variations and disturbance are presented to demonstrate the achievement of good robust performance.ce.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.837-843
• /
• 2006

As environmental vibration requirements on precision equipment become more stringent, use of pneumatic isolators has become more popular and their performance is subsequently required to be further improved. Performance of passive pneumatic isolators is related to various design parameters in a complicated manner and, hence, is very limited especially in low frequency range by chamber volume. In this study, transmissibility behavior of the pneumatic isolators depending on frequency and dynamic amplitude are presented. Then, an active control technique, time delay control, which is adequate for a low frequency nonlinear system, is applied. A procedure of applying the time delay control law to a pneumatic isolator is presented and it's effectiveness in the transmissibility performance is shown. Comparison between passive and active pneumatic isolators is made based on simulation.

• Proceedings of the KOR-KST Conference
• /
• 2002.02a
• /
• pp.143-159
• /
• 2002

The performance of two single-barrier three-phase actuated control systems at diamond interchanges was evaluated for various traffic conditions. To emulate the actuated signal control, hardware-in-the-loop system combined with CORSIM simulation program was used. Two performance measures, average delay and total stops, were used for the evaluation process. Results showed that the two three-phase systems gave similar performance in terms of average delay, but not stops. The delay performance of each phasing system was generally dependent on the traffic pattern and ramp spacing. The total stops decreased as the spacing increased, and it was the most sensitive variable that can differentiate between the two three-phase systems. It was also shown that the hardware-in-the-loop control could provide a good method to overcome the limitations of current simulation technology.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.2
• /
• pp.351-356
• /
• 2022

The parity function can be implemented with XOR (exclusive-OR) and XNOR (exclusive NOR) circuit. In this paper we propose a high performance XOR-XNOR circuit. The proposed circuitreduced the internal load capacitance on critical path and implemented with 8 transistors. The circuit produces a perfect output signals for all input combinations. Compared with the previous circuits, the proposed circuit presents the improved characteristics in average propagation delay time, power dissipation, power-delay product (PDP), and energy-delay-product (EDP). The proposed circuits are implemented with standard CMOS 0.18um technology. Computer simulations using SPICE show that the proposed circuit realizes the expected logic functions and achieves a reasonable performance.

• IE interfaces
• /
• v.11 no.3
• /
• pp.77-87
• /
• 1998

Intelligent Peripheral(IP) system is to provide specialized resource functions (SRF) such as playing announcement, collecting user information, and receiving messages in the Advanced Intelligent Network (AIN). We analyze the call processing capacity of an AIN IP system being developed in ETRI through an extensive simulation using SLAM II under a variety of AIN service scenarios. We consider televoting (VOT) and universal personal telecommunication (UPT) services which are to be provided at the fit implementation of the AIN in Korea. As the performance criteria to determine the call processing capacity, processor utilization, delay and call loss probability are considered. It turns out that the major processor called SAMP is the bottleneck processor, the service response delay dominates the delay performance, and the call loss probability becomes the primary criterion in determining the call processing capacity of the AIN IP system. It is also shown that the call processing capacity of the AIN IP system is determined by the utilization of the processor and the delay performance when the VOT ratio is below 70 percent but it is determined by the call loss probability due to the lack of service channels for providing the SRF operations.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.2
• /
• pp.36.2-36.2
• /
• 2016

In mm-VLBI, the quality of observation data is largely affected by atmospheric effect. The most challenging matter is that the phase of correlator output fluctuates rapidly resulting from a variation of atmospheric propagation delay. Consequently, it is demanding to achieve high Signal-to-Noise ratio by integrating data in time domain before calibrating atmospheric delay. However, Korean VLBI Network (KVN) has a unique system to make a 4-frequency (22/43/86/129 GHz) simultaneous observation in mm-wavelength and Frequency Phase Transfer (FPT) calibration technique has effectively removed atmospheric delay in the simultaneous multi-frequency observation of the KVN. For astrometric and astrophysical studies, we evaluated the FPT performance of KVN in various observing conditions. Using the total 38 bright AGNs, we have compared atmospheric conditions such as ground-based weather information, system temperature, atmospheric delay with the calibration results of FPT at 22/43/86/129 GHz during the five experiments in 2013, and quantified its performance in terms of coherence function and Allan variance. We present the analysis result of the relation between the FPT performance and observing conditions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.5
• /
• pp.546-551
• /
• 2016

The objective of this study is to investigate the response delays between piezo-stack actuator and the displacement magnifier of jetting dispenser and to reduce its falling time in terms of displacement optimization. The dispenser is driven by the dual piezo-stack actuators with a hinge lever mechanism to precisely control flow rate of the working fluid (3000 cP). It is commonly found that piezo actuator-driven jetting dispensers involving viscous working fluids have displacement optimization problem for ideal performance. The response delay of the system is caused by the phenomenon that the displacement magnifier cannot exactly follow the motion of the piezo actuators. The response delay may lower the performance of the system due to the inaccurate discharge of working fluid or even damages to the system itself due to inharmonious motion of piezo actuators with lever system. To reduce its response delay, a new displacement profile obtained from displacement optimization is suggested; its performance is tested through finite element analysis; and experiments are carried out to verify the performance of the obtained displacement profile.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.79-84
• /
• 2017

This paper is a multi-input multi-path (Multiple-input multiple-output: MIMO) using a space-alternating generalized expectation maximization(SAGE) algorithm in the parameter channel and determine the channel estimation performance. Estimated by the algorithm, SAGE time-varying channel environment, the channel parameters estimated from the parameters of the channel measured in the island region 781 of the band in order to compare the performance and compares the original data. This allows you to check the performance of the algorithm SAGE and is highly stable to delay spread (Delay Spread), the diffusion angle of arrival (Arrive of Angular Spread) performance in terms of accuracy down through the SAGE algorithm for estimating a more general calculation parameters.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12C
• /
• pp.199-207
• /
• 2001

We propose an adaptive shaping controller equipped with the technologies of shaping and buffering VoIP packets arriving at the receiving end by the CAM-type controller. In order to conceal interarrival packet delay variation, the conventional jitter buffers force them to be too large, thereby causing the audio quality to suffer excessive delay. However, by using our proposed method, the delay caused by shaping operation dynamically increases or decreases on the level of jitter that exists with in the IP network. This makes the delay accommodates adaptively the network jitter condition. The less jitter network has the fewer delay the shaping controller requires for jitter elimination. And the CAM-type method generally makes the shaping operation faster and leads to processing packets in as little time as can. We analyse the packet loss and delay performance dependency on the average talk ratio and the number of jitter buffer entries in shaping controller. Surprising, we show that the average delay using our shaping controller is about 70msec. This performance is much better than with the delay equalization method which forces the receiving end to delay about 60msec.