• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.1
• /
• pp.97-103
• /
• 2000

This paper deals with residual stresses induced at the viscoelastic adhesive layer between the semiconductor chip and the leadframe during adhesion process. The adhesive layer has been assumed to be“thermorheologically simple”. The time-domain boundary element method(BEM) has been employed to investigate the behavior of interface stresses. Numerical results show that very large stress gradients are present at the interface corner and such singularity might lead to local yielding or edge delamination.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3202-3218
• /
• 1994

Mode shapes and natural frequencies of vibrating laminated composite plates are taken using real-time and time-average holographic interferometry. Debonds and delamination in the laminated plates are measured nondestructively. During holographic testing of composite plates, it has been found that the conditions for the local resonance in debonds are strongly dependent on the frequency of excitation. A membrane resonance model was proposed to describe this behavior. Relations between characteristic length according to the size, shape of debonds and membrane resonance frequency are presented. Several experiments were performed to verify the membrane resonance model. The agreements between the predicted excitation frequency and the observed resonance frequency are good. The experimental results show that higher stresses and strains due to local resonance lead to the debond detection.

• Elastomers and Composites
• /
• v.51 no.4
• /
• pp.280-285
• /
• 2016

The purpose of this study is to get optimum design and operation conditions of the heating rubber roller for laminating process. The cause of performance degradation of heating rubber roller is delamination of rubber on metal tube, rubber aging due to high temperature. We measured the material properties of thermal expansion, thermal conductivity, specific heat and density and analyzed thermal distributions of rubber layer using finite element method. As a result of heat/flow analysis, the density distribution of heating coil must shorten the stabilization time by reducing the temperature deviation on the length direction at the temperature rising section after increasing the density of the area contacting with the laminate film at the center part which is an opposite of the current composition while enabling to maintain the temperature of heater to be consistent while maintaining the temperature deviation to be low when heat loss is created. Finally, we determined optimum heating method of heating rubber roller.

• Advanced Composite Materials
• /
• v.16 no.2
• /
• pp.115-134
• /
• 2007

This study proposes two new approaches for identifying damage patterns in a holed CFRP cross-ply laminate using an embedded fiber Bragg grating (FBG) sensor. It was experimentally confirmed that the reflection spectrum from the embedded FBG sensor was significantly deformed as the damage near the hole (i.e. splits, transverse cracks and delamination) extended. The damage patterns were predicted using forward analysis (a damage analysis and an optical analysis) with strain estimation and the proposed damage-identification method as well as the forward analysis only. Forward analysis with strain estimation provided the most accurate damage-pattern estimation and the highest computational efficiency. Furthermore, the proposed damage identification significantly reduced computation time with the equivalent accuracy compared to the conventional identification procedure, by using damage analysis as the initial estimation.

• Advanced Composite Materials
• /
• v.16 no.2
• /
• pp.135-149
• /
• 2007

In the automobile industry, structural health monitoring of fiber reinforced polymer composite parts is a widespread need for maintenance before breakdown of the functional elements or a complete vehicle. High performance sensors are generally used in many of the structural health monitoring operations. Within this study, a carbon fiber sewing thread has been used as a low cost laminate failure sensing element. The experimentation plan was set up according to the electrical conductance and flexibility of carbon fiber threads, advantages of preforming operations, and sewing mechanisms. The influence of the single thread damages by changing the electrical resistance and monitoring the impact location by using carbon thread sensors has been performed. Innovative utilization of relatively cost-effective carbon threads for monitoring the delamination of metallic inserts from the basic composite laminate structure is a highlighting feature of this study.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.519-522
• /
• 2005

Ka-Hwa highway bridge, located in a corrosive marine environment, had been examined the current condition of reinforcement corrosion in concrete throughout half-cell potentials, electrical resistivity, chloride contamination of concrete, and visual observation. According to the test, the chloride corrosion reinforced concrete structure is not only the protecting film around the reinforcement is deteriorated but also corrosion activity develops, for example, delamination areas of concrete. The purpose of this paper is to report the effects of Ka-Hwa highway bridge damaged by chlodide attack and to present the results of repair of Ka-Hwa highway concrete bridge in domestic marine environment.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.2
• /
• pp.35-41
• /
• 1996

This paper is aimed to solve local buckling problem that can frequently occur when the high speed ship's hull of sandwich structural type is crushed by rarbour and cargo. Experiment is performed on 36 specimens cut of 4-plates that made of sandwich type(Kevlar-Epoxy, Klegecell foam) and 16-Edgewise compressive test specimen, 16-Flatwise test specimen were tested by A.S.T.M. test method. The result of this study is analyzed and compared in test method and test jig to perorm Edgewise compressive test and Flatwise test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.322-322
• /
• 2008

Low-temperature co-fired ceramics (LTCC) have turned out to be very promising technology in accordance with the rapid developments in semiconductor technology. The demands for compact electrical assemblies, smaller power loss as well as high signal density can be fulfilled by LTCC. And for the multi-layered ceramic devices with embedded passive components such as high dielectric constant decoupling capacitor, LTCC materials require the several conditions to avoid delamination and internal cracks. For the present study, diopside-based glass is chosen as the LTCC substrate material in view of its high coefficient of thermal expansion (CTE). From the experimental resultsn the influence of each element on the CTE change can be revealed.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.37-44
• /
• 2003

In this proposed work, computational, finite element model far multi-delaminated plates will be developed. In the current analysis procedures of multi-delaminated plates, different elements are used at delaminated and undelaminated region separately. In the undelaminated region, plate element based on Mindlin plate theory is used in order to obtain accurate results of out-of-plane displacement of thick plate. And for delaminated region, plate element based on Kirchhoff plate theory is considered. To satisfy the displacement continuity conditions, displacement vector based on Kirchhoff theory is transformed to displacement of transition element. Element mass and stiffness matrices of each region (delaminated, undelaminated and transition region) will be assembled for global matrix.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.143-146
• /
• 2004

Fiber reinforced plastic material should be inspected in fabrication process in order to enhance quality by prevent defects such as delamination and void. Generally, ultrasonic technique is widely used to evaluate FRP. In conventional ultrasonic techniques, transducer should be contacted on FRP. However, conventional contacting method could not be applied in fabrication process and novel non-contact evaluating technique was required. Laser-based ultrasonic technique was tried to evaluate FRP plate. Laser-based ultrasonic waves propagated on CFRP were received with various transducers such as accelerometer and AE sensor in order to evaluated the properties of waves due to the variation of frequency. Velocities of laser-based ultrasonic waves were evaluated for various fiber orientation.