• 대한조선학회논문집
• /
• 제36권3호
• /
• pp.122-133
• /
• 1999

완성되어진 블록을 이용한 탑재의 과정에서 발생하는 블록 경계간의 판재 겹쳐짐 현상, 과도한 간격 및 단차의 발생현상은 선박의 건조비용과 공수를 증가시키는 요인이 된다. 본 논문에서는 블록의 조립 및 탑재에 관한 시뮬레이션 시스템을 제안하고 이중 조립에 관한 시뮬레이션을 용접순서에 따라 용접변형 및 자중을 고려하여 유한요소해석을 ANSYS를 이용하여 수행하였다. 용접에 의한 변형은 실험에 의한 변형량을 이용한 등가강성에 따른 등가 하중을 사용하여 탄성적인 해석법을 수행하여 예측하였으며 선체 이중저 평블록을 패널 조립법에 근거한 조립순서에 따라 시뮬레이션을 수행하였다. 시뮬레이션을 통한 변형으로부터 조립순서에 따른 중간 제품의 형상의 변화에 의한 강성의 변화에 기인한 변형량의 차이를 확인 할 수 있었으며, 자중의 효과를 반드시 고려하여야 함을 확인 할 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.102-103
• /
• 2014

Due to the nature of the existing load, the criteria of assessing the intensity of the lightweight wall's impact resistance has been though of as obscure. The current study, therefore, focuses on the standardized assessment of the impact resistance to the force of the large soft body applying to the lightweight wall. The gypsum board wall showed a low level of the maximum residual displacement. It is, however, required to be careful about the selection of the finishing process since the high level of the maximum displacement is likely to cause harm to finishing materials. Unlike the gypsum board, the ALC block wall displayed a considerable rigidity while showing almost no maximum residual displacement. Even with the low level of the maximum displacement due to the stiffness, the ALC block wall is still likely to be affected by the vibration derived from any impact on the surface, which demands a need for additional study. The future experimental study, accordingly, will focus on the impact of the vibration on finishing materials, consequently leading to the accurate prediction of the possibility of potential damage to the lightweight wall caused by the large soft body.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.730-737
• /
• 2004

In this paper, in order to examine cyclic hehavior characteristics and safety of underground flexible pipes for electric cables subject to cyclic vehicle load, FEM analysis and cyclic soil box test were carried out. As results of the test, it was revealed that the vertical displacement of the test was larger than that of FEM analysis because thermal effect arising from power cables made reduction of rigidity of the pipe so that large deformation of the pipe induced by the heat occured. Moreover, it was shown that the final vertical displacement under about 0.4 million times of the cyclic load test was not satisfied with elastic allowable displacement of the pipe, and long term stability of the pipe was not stable since behavior characteristics of the pipe exists plastic strain range pasted clastic strain range.

• 동력기계공학회지
• /
• 제17권1호
• /
• pp.97-103
• /
• 2013

Press machine has advantages over other manufacturing machine which can produce large quantities of products in short time so it is widely used in lots of industrial sectors. To obtain the vehicle's weight lightening and rigidity of the body-frame by applying 'Hot stamping' technique is increasing in the automotive field. In this paper, to improve the irregular vibration arose by 800Ton hot stamping press, the research was continued. Bed, slide and main frame are the key part of working precision, so perform structural analysis was conducted, and based on the analyzing results, structural changes were done on the parts where structural deformation occurred.

• 한국기계가공학회지
• /
• 제19권1호
• /
• pp.100-107
• /
• 2020

As demand for high value-added products with hard materials increases, the line center is used for producing high value-added products in many industries such as aerospace, automobile fields. The line center is a key device for smart factory automation that can improve the production efficiency and the productivity. Therefore, the development of a mill-turn line center is necessary to produce high value-added products with complex shapes flexibly. In the mill-turn process, a milling process and a turning process are combined. In particular, the turning process needs to increase the rigidity of the spindle. The purpose of this study is to analyze the thermal-structural stability through thermo-structural coupled analysis for a mill-turn spindle with a curvic coupling. The maximum temperature and thermal stability of the spindle were analyzed by thermal distribution. In addition, the thermal deformation and thermal-structural stability of the spindle were analyzed through thermo-structural coupled analysis.

• 정보저장시스템학회논문집
• /
• 제2권4호
• /
• pp.245-250
• /
• 2006

Organizations such as broadcasting stations and libraries which deal with huge amount of information require high-capacity storage systems for archiving their materials and information. It is necessary and urgent for the storage people to develop a compact, high capacity, and low-cost data storage systems. Even though the Blue-ray technology is commercialized and now it is on the market, demand for the compact and low-cost system is still increasing. A flexible disk system has been introduced recently to satisfy above mentioned requirements. The system uses multiple of thin disks and is expected to achieve technical requirements. However, decreasing the disk thickness makes it difficult to read and write data because it decreases the disk rigidity so that the transverse vibration of the rotating disk increases easily due to both the interaction with surrounding air and the vibration characteristics of thin flexible disk itself. In this study, flat-type stabilizer is proposed to suppress the transverse vibration of a $95{\mu}m$-thick polycarbonate disk. Characteristics of disk vibration have been studied through the results of numerical analysis from the fluid mechanics point of view. Numerical simulation is verified through the experiment by measuring the gap between the rotating disk and the stationary flat stabilizer. The axial deflections of the disk are computed for various rotating speeds and reference gap sizes and then a method of regression is applied to those data. As a result, an empirical relation is proposed for the steady deformation shape of the rotating disk.

• Structural Engineering and Mechanics
• /
• 제37권3호
• /
• pp.309-320
• /
• 2011

As a new type of large-span space structure, suspendome is composited of the upper single-layer reticulated shell and the lower cable-strut system. It has better mechanical properties compared to single-layer reticulated shell, and the overall stiffness of suspendome structure increases greatly due to the prestress of cable. Consequently, it can cross a larger span reasonably, economically and grandly with high rigidity, good stability and simple construction. For a better assessment of the advantages of mechanical characteristic of suspendome quantitatively, the static behavior of Kiewitt6 suspendome was studied by using finite element method, and ADINA was the software application to implement the analysis. By studying a certain suspendome, the internal forces, deformation and support constrained forces of the structure were obtained in this paper. Furthermore, the influences of parameters including prestress, stay bar length, cross-sectional area and rise-to-span ratio were also discussed. The results show that the increase of prestress and vertical stay bar length can improve the stiffness of suspendome; Cross-sectional area has nearly no impact on the static behavior, and the rise-to-span ratio is the most sensitive parameter.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 봄 학술발표회 논문집
• /
• pp.93-100
• /
• 1998

The basic systems of spatial structures such as shells, membrane, cable-nets and tensegrity structure have been developed to create the large spaces without column. These structures may have large freedom in scale and form, and especially tensegrity structures are received much attention from the view points of their light weight and aesthetics. But There re some difficulties concerning structural stability, surface formation and construction method. One of the way to solve these problems reasonably is a combination of tensile members and rigid members. A structural system based on this concept is referred to as the "HTS ( Hybrid Tension Structure )". This is a type of flexible structural system which is unstable initially, because the cable material has little initial rigidity. As cable - dome hybrid structures is a type of HTS, the initial stress for the self- equilibrated system having stable state have to be introduced. To determine initial stress having stable state, the shape finding analysis is required before the stress - deformation analysis. In this paper, the primary objective is to derive the nonlinear finite element formula of cable and truss members considering geometric nonlinearity for shape finding of cable-dome, and to propose the method to decide the initial stress by the shape analysis of cable-dome hybrid structure with the self-equilibrated state.

• 복합신소재구조학회 논문집
• /
• 제2권3호
• /
• pp.12-17
• /
• 2011

본 논문은 노후교량바닥판 대체용으로서 하이브리드 GFRP-강재 바닥판의 휨거동을 구조적 거동특성을 기술하고 있다. 하이브리드 GFRP-강재 바닥판의 구조적 특성을 조사하기 위해 정적하중의 실험적 연구를 수행하였다. 하이브리드 바닥판의 파괴모드는 초기항복을 지나서 연성거동을 나타내었다. 결과는 유한요소프로그램 ANSYS의 값과 비교하였다. 제안된 하이브리드 바닥판이 교량적용에 유용함을 확인하였다. 하이브리드 바닥판의 두께는 유사한 휨 강성을 갖는 완전복합신소재 바닥판께와 비교하였을 때 감소될 수 있었다.

• Steel and Composite Structures
• /
• 제20권2호
• /
• pp.431-445
• /
• 2016

Seismic behavior of new composite structural system with a fabricated floor was studied. A two-bay and three-story structural model with the scale ratio of 1/4 was consequently designed. Based on the proposed model, multiple factors including energy dissipation capacity, stiffness degradation and deformation performance were analyzed through equivalent single degree of freedom pseudo-dynamic test with different earthquake levels. The results show that, structural integrity as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without concrete topping. It is proved that the cast-in-place floor in areas with high seismic intensity can be replaced by the prefabricated floor without pouring surface layer. The results provide a reliable theoretical basis for the seismic design of the similar structural systems in engineering application.