• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.407-414
• /
• 2000

This paper presents measured deformation of geomembrane installed on slopes of a landfill. The layout of geosynthetics installed on landfill slopes as required by regulations is composed of, in typical, geocomposite, geomembrane, geosynthetic clay liner in turn from the slope. An effort was made to better understand the sources of external forces acting on geosynthetics and their interactions. The results of a field observation indicated that tensile stresses induced on geomebrane were far less in magnitude than predicted by the design method employing mass equilibrium of waste. This was mainly because external forces acting on slopes were not transferred from geocomposite to underlying geomembrane. A simple, but rather rational method for assessing the stability of geosynthetics against tensile stresses was proposed. This method is based on a hypothesis that external forces acting on geosynthetics are the results of downdrag of waste during waste compaction.

• Journal of Ocean Engineering and Technology
• /
• v.2 no.1
• /
• pp.163-169
• /
• 1988

A beach nourishment method can be used as one of the beach. The beach nourishment is affected br a natural condition and an artificial condition; a natural condtion include conditions of bottom slope, diameter of bottom materials and wave, and an artificial condition include deposit position, method, diameter and quantity of the nourishing sand. To obtain and the best diameter of the nourishing sand a two-dimensional hydraulic model test, which simulates the erosional beach, has been accmplished. In this study the protection of the beach erosion can be maximized when the nourishing sand of 0.84mm in diameter, which is about 2.5-3.5 times of the natural bottom materials in diameter.

• Agricultural and Biosystems Engineering
• /
• v.1 no.1
• /
• pp.38-42
• /
• 2000

Though the freshness for agricultural products is an important factor related to their quality management, this terminology is being used restrictedly because it is very subjective. In this study, a dimensionless index which had the span of the maximum of 1 through the minimum of 0 was proposed to describe freshness of the product with time-variant quality and was applied to Tsugaru and Fuji apples. First, the compressive properties having the linearity in their change regarding time elapsed after harvest were selected. For Tsugaru apple, bio-yield and rupture forces had high correlation with time while for Fuji, bio-yield and rupture deformations had high correlations. When the slope, or ratio of force to deformation, was considered, the effect of cultivar could be neglected. When the linearly time-variant compressive properties for Tsugaru and Fuji apples were involved in the freshness indices, they described well freshness of apples. Also, the freshness decay constant depicted a characteristic which related to freshness decay rate. Therefore, the freshness index can be utilized to manage the quality during storage and distribution of apples.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.924-927
• /
• 2007

In this study, adaptation of two-way shape memory effect of SMA wire to the actuator is examined. Therefore the SMA characteristics which are training, material properties, response time at different thermal cycling rates are tested. During training, permanent deformation is accumulated till a certain number of cycle and then saturated. The amount of two-way strain is unchangeable over all cycle and the slope of strain(or stress)-temperature curve is slower as the increase of applied stress. The rate effect is observed resulted from the thermal distribution which heating profile differs from cooling as thermal cycling time. Using the estimated SMA properties, an experimental test for the simple smart wing is performed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.145-148
• /
• 2005

In this study, adaptation of two-way shape memory effect of SMA wire to the actuator is examined . Therefore the SMA characteristics which are training, material properties, response time at different thermal cycling rates are tested. During training, permanent deformation is accumulated till a certain number of cycle and then saturated. The amow1t of two-way strain is unchangeable over all cycle and the slope of strain(or stress)-temperature curve is slower as the increase of applied stress. The rate effect is observed resulted from the thermal distribution which heating profile differs from cooling as thermal cycling time. Using the estimated SMA properties, an experimental test for the simple smart wing is performed.

• Structural Engineering and Mechanics
• /
• v.19 no.6
• /
• pp.749-755
• /
• 2005

In this work, thermo-elastic stability behavior of laminated cross-ply elliptical cylindrical shells subjected to uniform temperature rise is studied employing the finite element approach based on higher-order theory that accounts for the transverse shear and transverse normal deformations, and nonlinear in-plane displacement approximations through the thickness with slope discontinuity at the layer interfaces. The combined influence of higher-order shear deformation, shell geometry and non-circularity on the prebuckling thermal stress distribution and critical temperature parameter of laminated elliptical cylindrical shells is examined.

• Computational Structural Engineering
• /
• v.4 no.3
• /
• pp.129-135
• /
• 1991

This paper reports the application study of the ground reinforcement under a buried pipeline subjected to differential settlement via a finite element modeling. The soil-reinforcement interaction helps to minimize the differential settlement between the adjoining pipe segments. The settlement pattern and deformation slope of a pipeline have been evaluated for a boundary condition at the joint between a rigid structure and a pipeline. The analysis results are compared for both non-reinforced and reinforced cases to numerically evaluate the stress transfer mechanism and the effectiveness of the soil reinforcement for restraining the settlement of the pipeline.

• Tunnel and Underground Space
• /
• v.17 no.5
• /
• pp.350-359
• /
• 2007

Most large cut slopes of open pit mines, roadways, and railways are steeply inclined and composed with rocks that do not contain soils. However, these rock slopes suffer both weathering and fragmentation. In the case of steep slopes, falling rock and collapse of a slope may often occur due to surface erosion. Cast-in place concrete and rubble work are the most widely used earth structure-based pressure supports that act as restraints against the collapse of the rock slope. In order to overcome the shortcomings of conventional retaining walls, a segmental grid retaining wall is being used with connects precasted segments to construct the wall. In this study, laboratory model test was conducted to estimate deformation behavior of segmental grid retaining wall with configuration of rear strecher, height and inclination of the wall. In order to examine the behavior characteristics of a segmental grid retaining wall, this research analyzes the aspects of spacial displacement through relative displacement according to change in the inclination of the wall. Also, the walls behavior according to the formation and status of the rear stretcher which serves the role of transferring the load from the header and the stretcher which make up the wall, the displacement of backfill materials in the wall, and the location of the maximum load were surveyed and the characteristics of displacement in the segmental grid retaining wall were observed. The test results of the segmental grid retaining wall showed that there was a sudden increase in failure load according to the decrease in the wall's height and the size of the in was greatly decreased. Furthermore, it revealed that with identical inclination and height, the structure of the rear stitcher did not greatly affect the starting point or size of maximum horizontal displacement, but rather had a stronger effect on the inclination of the wall.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.523-534
• /
• 2010

A hybrid system of soil-nailing and compression anchor is proposed in this paper; the system is composed of an anchor bar (installed at the tip) with two PC strands and a steel bar. After drilling a hole, installing proposed hybrid systems, and filling the hole with grouting material, prestress is applied to the anchor bar to restrict the deformation at the head and/or to prevent shallow slope failures. However, since the elongation rate of PC strand is much larger than that of steel bar, yield at the steel bar will occur much earlier than the PC strand. It means that the yield load of the hybrid system will be overestimated if we simply add yield loads of the two - anchor bar and PC strands. It might be needed to try to match the yielding time of the two materials by applying the prestress to the anchor bar. It means that the main purpose of applying prestress to the anchor bar should be two-fold: to restrict the deformation at the nail head; and more importantly, to maximize the design load of the hybrid system by utilizing load transfer mechanism that transfers the prestress applied at the tip to the head through anchor bar. In order to study the load transfer mechanism in a systematic way, in-situ pullout tests were performed with the following conditions: soil-nailing only; hybrid system with the variation of prestress stresses from 0kN to 196kN. It was found that the prestress applied to the anchor system will induce the compressive stress to the steel bar; it will result in decrease in the slope of load-displacement curve of the steel bar. Then, the elongation at which the steel bar will reach yield stress might become similar to that of PC strands. By taking advantage of prestress to match elongations at yield, the pullout design load of the hybrid system can be increased up to twice that of the soil-nailing system.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.4
• /
• pp.1-10
• /
• 2022

In this study, to evaluate the possibility of using a steel spring as a displacement-dependent damping device, tensile loading and cyclic loading tests were performed. The main experimental variables were the type of steel (SAE9254 and SS275), the spring constant (700 N/mm, 1,000 N/mm, and 1,400 N/mm), and the presence or absence of heat treatment for SAE9254. As a result of the tensile test, the ratios of the measured spring constant to the design spring constant of the steel springs made with SAE9254 ranged from 1.08 to 1.13, while the ratios of the design spring constant and the measured spring constant of the steel springs made with SS275 ranged from 0.86 to 0.97. After yielding, the slope values of the load-displacement curve of the SAE9254 with/without heat treatment were about 240~251 N/mm and 92 N/mm, respectively, but the slope values of the load-displacement response of SS275 were almost zero. According to the uniaxial cyclic loading test results, all specimens were satisfied with three conditions for a displacement-dependent damping device in KDS 41 17 00 (2019): the maximum force and minimum force at zero displacement, the maximum force and minimum force at the maximum displacement, and the energy dissipation capacity. In addition, the equivalent damping ratios of steel springs made with SAE9254(non-heat treatment) and SS275 were approximately 2.8 times and 1.9 times greater, respectively, than that of steel springs made with SAE9254.