• Earthquakes and Structures
• /
• 제26권1호
• /
• pp.1-15
• /
• 2024

Isolation technology has been proven effective in reducing the seismic response of superstructures, where most of the deformation is concentrated in the isolation layer. However, in cases of earthquakes with intensities surpassing the fortification level of the area, or severe near-fault earthquakes, the isolation layer may experience excessive deformation, resulting in damage to the isolation bearings or collisions with the retaining wall or surrounding buildings. In this study, a finite element model using ABAQUS is established and compared with experimental test results to deeply investigate the influence of limit devices on the isolation layer and its response to the superstructure. The findings reveal that a larger limiter stiffness and a smaller reserved gap can achieve a more effective limiting effect. Nevertheless, a smaller reserved gap and a larger limiter stiffness may result in increased response of the superstructure. Therefore, rational selection of the reserved gap and limiter stiffness is crucial to reduce the acceleration response.

• Structural Engineering and Mechanics
• /
• 제35권1호
• /
• pp.67-82
• /
• 2010

The beam string structure (BSS) has been widely applied in large span roof structures, while no analytical solutions of BSS were derived for it in the existing literature. In the first part of this paper, calculation formulas of displacement and internal forces were obtained by the Ritz-method for the most commonly used arc-shaped BSS under the vertical uniformly distributed load and the prestressing force. Then, the failure mode of BSS was proposed based on the static equilibrium. On condition the structural stability was reliable, BSS under the uniformly distributed load would fail by tensile strength failure of the string, and the beam remained in the elastic or semi-plastic range. On this basis, the limit load of BSS was given in virtue of the elastic solutions. In order to verify the linear elastic and limit state solutions proposed in this paper, three BSS modal were tested and the corresponding elastoplastic large deformation analysis was performed by the ANSYS program. The proposed failure mode of BSS was proved to be correct, and the analytical results for the linear elastic and limit state were in good agreement with the experimental and FEM results.

• 콘크리트학회지
• /
• 제9권3호
• /
• pp.179-187
• /
• 1997

콘크리트는 여러 구성 성분들이 불규칙적인 배열을 이루어 형성된 복합재료이지만, 과거에는 이 재료를 하나의 단종재료로 간주하여 해석하였기 때문에, LEFM에서 사용되는 파괴인성계수만으로는 콘크리트의 파괴역학적 접근이 어렵다는 것 이외에는 파괴인성계수들의 크기의존성에 대한 이유라든가, 실험을 통해서 관측된 구조물 두께 방향으로의 서로 다른 깊이의 균열 진행 현상에 대해서는 설명하기가 어려웠다. 따라서 본 연구는 콘크리트를 하나의 복합재료로써 각각의 구성요소들이 차지하고 있는 체적비 및 배열상의 효과를 고려하여 복합재료의 파괴거동을 해석하고, 구성재료의 수와 파괴인성계수와의 상관관계를 분석하였다. 각각의 구성요소들을 연립변형모드( SD mode)로 배열시킨 조건에서 복합재료역학개념에 입각하여 해석한 결과, 일반적으로 실험이나 비선형파괴역학 해석과 같이 하중-변위곡선 상단부에서 비선형 거동이 관측되었다. 또한 임계응력확대계수( $K_IC$)나 파괴에너지($G_r$)는 구성원의 수나 보의 크기에 대해서 거의 무관한 값을 나타내지만, 임계군열선단개구변위 ($CTOD_c$)는 크기에 영향을 받음을 보여 주었다. 균열의 진행속도는 균열이 진행될수록 감소하며, 파괴인성이 작은 구성원에서부터 균열이 발생되어 결과적으로 보의 두께 방향으로 서로 다른 크기의 균열길이가 생성됨이 관측되었다.

• 한국농공학회논문집
• /
• 제46권1호
• /
• pp.41-51
• /
• 2004

FRP re-bar in concrete structures could be used as a substitute of steel re-bars for that cases in which aggressive environment produce high steel corrosion, or lightweight is an important design factor, or transportation cost increase significantly with the weight of the materials. But FRP fibers have only linearly elastic stress-strain behavior; whereas, steel re-bar has linear elastic behavior up to the yield point followed by large plastic deformation and strain hardening. Thus, the current FRP re-bars are not suitable concrete reinforcement where a large amount of plastic deformation prior to collapse is required. The main objectives of this study in to evaluate the tensile behavior and the fracture mode of hybrid FRP re-bar. Fracture mode of hybrid FRP re-bar is unique. The only feature common to the failure of the hybrid FRP re-bars and the composite is the random fiber fracture and multilevel fracture of sleeve fibers, and the resin laceration behavior in both the sleeve and the core areas. Also, the result of the tensile and interlaminar shear stress test results of hybrid FRP re-bar can provide its excellent tensile strength-strain and interlaminar stress-strain behavior.

• 콘크리트학회논문집
• /
• 제26권4호
• /
• pp.545-553
• /
• 2014

이 연구는 PC 보-기둥 접합부의 일반적인 거동의 접합 상세에 따른 통합적 평가 방안을 제안하였다. 이 연구는 접합부의 파괴 패턴과 이에 연관된 접합부 상세의 특징을 정량적으로 표현하기 위해 접합부와 각 요소들이 보유한 변형기여분을 사용할 것을 제안하였다. 이에 따라 PC 접합부는 '일체식 접합부'와 '연결식 접합부'로 크게 분류되었다. 접합부의 분류를 위한 기준 사항의 제안 및 검증을 위해 네 개의 보-기둥 실험체의 실험을 수행하였다. 실험은 일반적인 보-기둥 접합부의 실험 방법과 같은 방법으로 진행되었다. 가력은 접합부 상부 기둥의 끝단에서 수행되었으며, 보 양단은 힌지로 고정되었다. 변형기여분의 평가를 위해 총 34개의 LVDT가 주요 변형이 발생할 것으로 예상되는 곳에 설치되었다. 실험 결과 세 개의 실험체에서 나타난 각 요소들의 변형기여분은 수치적으로 다른 특성을 가지고 있는 것을 확인할 수 있었다. 실험 결과를 기반으로 접합부의 변형 정도와 다른 요소들의 변형 정도에 의거하여, 접합부의 변형이 적고 보의 휨 변형이 크게 나타나는 강한 접합부와 접합부의 변형이 용인되는 연성 접합부로 일체식 접합부를 분류할 수 있었다.

• 한국정밀공학회지
• /
• 제10권4호
• /
• pp.109-117
• /
• 1993

Force balance method is employed to predict forging information such as forging load, tool pressure and normal stress at the surface of tangential velocity discontinuity. The incipient stages of deformation for the plane strain forging of rectangular billets in V-shaped dies of different semi-angles are analysed. To construct an approximate model for the analysis of deformation by the force balance method in the incipient deformation stages, slip-line field is used. When the deformation mode by slip-line method is the same as that by force balance method, the slip-line method and the force balance method give identical solutions. The effects of die angle, coefficient of friction, billet geometries and deforma- tion characteristics are also investigated. In order to verify the validity of force balance analysis, the rigid-plastic finite element simulation for the various forgig parameters are performed and performed and find to be in good agreement.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.1225-1228
• /
• 2004

We have studied the Polymer Stabilized Continuous Director Rotation (PSCDR) mode to solve the thermal shock problem which is core and main problem in CDR mode. The cell filled 95wt. % R2301 FLC and 5wt. % UCL-001 polymer is applied a low DC voltage only near the phase transition temperature from cholesteric to chiral smectic C phase transition to get defect-free alignment. In the previous work, we also confirmed layer deformation induced by an applied DC field only near the phase transition temperature from Ch to $SmC^{\ast}$. Results of layer structure, and characteristics of electro-optical properties between CDR and PSCDR mode will be discussed in this paper. We are also in progress to finalize the layer structures compared between CDR and PSCDR mode by x-ray measurements.

• Journal of Information Display
• /
• 제5권2호
• /
• pp.39-42
• /
• 2004

A novel fast-switching LCD with dual-domain bend (DDB) mode is described. DDB alignment is achieved using antiparallel-rubbed cell filled with chiral-doped LC. Initial alignment is mono-domain 180-degree twist. Tilt direction is controlled by oblique electric field to be counter direction in each domain. Twist-to-DDB deformation occurs continuously so that DDB mode does not require high-voltage initialization which is inevitable in Optically Compen sated Bend (OCB) mode. DDB gives wide and symmetric viewing angle in contrast to mono-domain bend formed from 180-degree twist showing strong asymmetry.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권4호
• /
• pp.21-25
• /
• 2005

In the dynamic analysis of a mechanism, if one or more of the components are flexible, then the simulation will not be accurate because of the violation of the rigid body assumption. Mode shapes are used to represent the dynamic behavior of an elastic structure. A modal synthesis method which uses a combination of normal modes, constraint modes, and attachment modes, was used to represent effectively the elastic deformation of a flexible multibody. Since the combination of these modes should be different for each type of connecting part, the modal synthesis method was studied for the various types of interconnecting joints. In addition, the analysis procedure for the flexible body was explained. A satellite system with flexible solar panels was chosen as an example to show the effectiveness of the proposed method.

• 한국전산구조공학회논문집
• /
• 제25권3호
• /
• pp.185-194
• /
• 2012

이 연구는 회전관성과 전단변형을 동시에 고려한 변단면 Timoshenko 보의 자유진동에 관한 연구이다. 변단면 보의 단면은 폭이 포물선 함수로 변화하는 변화폭 직사각형 단면으로 채택하였다. 이러한 보의 자유진동을 지배하는 수직변위에 대한 4계 상미분방정식을 유도하였다. 이 상미분방정식을 수치해석하여 고유진동수와 진동형을 산출하였다. 수치해석 예에서는 회전-회전, 회전-고정, 고정-고정 지점을 고려하였다. 진동형은 변위의 진동형뿐만 아니라 합응력의 진동형도 산출하여 그림에 나타내었다. 휨 회전각과 전단변형에 의한 수직변위 및 전단면 회전각의 구성비율을 산정하였다.