• 한국표면공학회지
• /
• 제34권5호
• /
• pp.391-394
• /
• 2001

A new type plasma reactor is proposed to decompose CF4 diluted with N2 gas in atmospheric pressure. The arc plasmas is surrounded with a waterwall which acts as a source of water vapor, the solvent of HF, resultant product after decomposition, and conveyer to take away fluorine compound from exhaust gas. Abatement more than 99% is achieved by small size plasmas such as 1 cm in diameter, 25cm in length and 3.4KW of DC discharge power in such gas as the mixture of 100 sccm of CF4 and 15 slm of N2. Reactors of this type are to be expanded to such a system as Nitrogen flow of 50 slm with 200 sccm of CF4 and 7-8 KW discharge power.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.37-40
• /
• 1996

Cable-In-Conduit Conductor(CICC) is widely accepted as an advanced superconductor configuration for large scale applications such as tokamak fusion reactors, MAGLEV (MAGnetic LEVitation), and SMES (Superconducting Magnetic Energy Storage). The stability of CICC cooled with supercritical helium can be very high if it is operated below a certain limiting current. This limiting current can be determined by Stekly type heat balance equation. The stability characteristic of CICC for AC operation is more complicated than that of DC because there are additional instability sources which are associated with local flux change. Ramp-rate limitation is a phenomenon discovered during US-DPC (United States-Demonstration Poloidal Coil) program, which showed apparent quench current degradation associated with high dB/dt. This paper describes recent experimental investigation results on the ramp-rate limitation and discusses current imbalance, induced current, current redistribution due to local quench of the strand in the cable.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(1)
• /
• pp.464-470
• /
• 1997

Severe accident analysis has been performed for the Wolsung nuclear power plants in Korea to investigate severe accident phenomena of CANDU-600 reactors as a part of Level II PSA study. The accident sequence analyzed in this paper is loss of active heat sinks(LOAH) which is caused by loss of off-site power, diesel generators, and DC power. ISAAC (Integrated Severe Accident Analysis Code)computer code developed by KAERI (Korea Atomic Energy Research Institute) was used in this analysis. This paper describes the important thermal-hydraulics and source term behaviors in the primary system and inside containment, and the failure mechanism of calandria vessel and containment. In addition, some insights for accident management program(AMP) are also given.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.556-558
• /
• 1994

This paper proposes a new converter that can reduce the harmonics like conventional 12-pulse dual thyrister converters with the input transformers. Both the bridges are controlled with the shifted firing angle and connected through current sharing reactors. Using the center tapped reactor, the DC link current is controlled with the different two values in order to make the input current waveform 12 pulses.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2002년도 동계연구발표회 논문개요집
• /
• pp.202-203
• /
• 2002

Ribbon type nanocrystalline alloy cores have shown excellent soft magnetic properties in the high frequency range because of small crystalline anisotropy and nearly zero magnetostriction[1]. In present, however ribbon alloys gives some limit in applications such as a large inductor and reactors of PFC circuit, which are required good DC bias property and low loss in the high frequency. Powder alloys with ultra fine grain structure can be an important way to overcome this kind of disadvantage, and to improve the high frequency soft magnetic properties in conventional metallic powder cores[2]. (omitted)

• 한국철도학회논문집
• /
• 제7권1호
• /
• pp.1-8
• /
• 2004

A newly-built inverter has to undergo a series of stress tests in the final stage of production line. This can be achieved by connecting it to a dynamometer consisting of a three-phase machine joined by a rigid shaft to a DC load machine. The latter is controlled to create some specific load characteristic needed for the test. In this paper a test method is proposed, in which no mechanical equipment is needed. The suggested test stand consists only of a inverter to be tested and a simulator converter. Both devices are connected back-to-back on the AC-side via smoothing reactors. The simulator operates in real-time as an equivalent load circuit, so that the device under test will only notice the behaviour of a three-phase machine under consideration of the load. In oder to prove rightness of the suggested test method, the simulation and actural experiment carried out emulation for a 2.2kW induction motor.

• 한국결정성장학회지
• /
• 제18권3호
• /
• pp.101-104
• /
• 2008

GaN films were grown on the vertical and horizontal reactors by the hydride vapour phase epitaxy (HVPE). The structural and optical characteristics of the GaN films were investigated depending on the reactor-type. GaN epilayers were characterized by double crystal X-ray diffraction (DC-XRD), transmission electron microscopy (TEM) and photoluminescence (PL). Surface defects of two kinds of the GaN films were revealed by the wet chemical etching method, using $H_3PO_4$ acid at $200^{\circ}C$ for 8 minutes. Hexagonal etch pits were analyzed by optical microscopy and SEM. Etch pit densities were calculated to be approximately $1.4{\times}10^7$ and $1.2{\times}10^6\;cm^{-2}$ for GaN layers grown on horizontal and vertical reactors, respectively. Those results show GaN grown in the vertical reactor having a better quality of optical properties and crystallinity than that in the horizontal reactor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.983-985
• /
• 2002

This paper is the machine that is able to estimate a new built power convertor in a production line. Generally, this machine test can be achieved by connecting it to a dynamometer consisting of a three-phase machine joined by a rigid shaft to a DC load machine. But the proposal system is controlled to create some specific load characteristic needed for the test without any mechanical equipment. The suggested test stand consists only of a converter to be test and a simulator converter. Both devices are connected back-to-back on the AC-side via smoothing reactors. The simulator operates in real-time as an equivalent load circuit, so that the device under test will only notice the behaviour of a three-phase machine under consideration of the load. And then, to obtain a superior characteristic for dynamic reference used the feedforward control.

• Nuclear Engineering and Technology
• /
• 제41권8호
• /
• pp.989-994
• /
• 2009

We at Mitsubishi have lined up Gen-III+ solutions for a wide variety of global customers: ATMEA1 of the 1100MWe class, and an APWR with the largest capacity of 1700MWe. In this paper, we would like to introduce the APWR. With an increased requirement for nuclear power generation as an effective countermeasure against global warming, we have established the APWR plant, a large-capacity Mitsubishi standard reactor combining our accumulated experience and technology as an integrated PWR plant supplier. The APWR plant has achieved high reliability, safety and enhanced economy based on a technology that has been developed with the support of the government and utilities through improvement and standardization programs of light water reactors. Currently, Tsuruga Units 3 and 4, the first two APWRs, are undergoing licensing, while we are making efforts to obtain the standard design certification (DC) of US-APWR and preparing for the European Utility Requirements (EUR) compliance assessment of EU-APWR. Mitsubishi Heavy Industries, Ltd. (MHI) positions the APWR as a core technology that will contribute to the prevention of global warming and meet worldwide requirements.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.765-768
• /
• 2003

In the end of a production line a new built power converter has to undergo a series of stress tests. This can be achieved by connecting it to a dynamometer consisting of a three-phase machine joined by a rigid shaft to a DC load machine. The latter is controlled to create some specific load characteristic needed for the test. In this paper a test method is proposed, in which no mechanical equipment is needed. The suggested test stand consists only of a converter to be tested and a simulator converter. Both devices are connected back-to-back on the AC-side via smoothing reactors. The simulator operates in real-time as an equivalent load circuit, so that the device under test will only notice the behaviour of a three-phase machine under consideration of the load.