• Progress in Superconductivity and Cryogenics
• /
• v.12 no.2
• /
• pp.5-8
• /
• 2010

In this study, the effect of bending strain on the transport property and critical current of lap and butt-jointed (non-laminated) BSCCO tapes has been investigated. The samples were joined using a mechanically controlled jointing procedure. To achieve a uniform thickness at the joint a single point loading contact has been devised. GFRP mandrels with different bending radii which support the sample during bending have been used. $I_c$ have been measured at 77 K and self field. In the case of easy bending test for jointed BSCCO tapes, sudden degradation of $I_c$ is caused by the local strain concentration due to non uniform deformation at the edge parts of the joint. In the case of hard bending test of jointed BSCCO tapes transverse macroscopic crack at specific subsection caused a large $I_c$ degradation. The transport property of jointed BSCCO tapes in each bending mode was discussed with the damage morphology occurred.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1422-1430
• /
• 1995

Al6061 alloy reinforced with 15 volume% of Saffil fibers was fabricated by squeeze infiltration method. Uniform distribution of reinforcements and good bondings between reinforcements and matrix alloy were found in the microstructure of composites. Comparing with A16061 matrix alloy, tensile strength and elastic modulus of $Al_{2}$O$_{3}$/Al composites were increased up to 26% and 31%, respectively. Cyclic deformation and fatigue behavior of $Al_{2}$O$_{3}$/Al metal matrix composites were studied. The specimens were cycled using tension-tension(R=0.1) loading and under load controlled fatigue test. Cyclic stress-displacement curve through fatigue test was obtained. Fatigue strength of $Al_{2}$O$_{3}$/Al composites was about 200 MPa, i.e.0.55 of applied stress level(q). During fatigue test, $Al_{2}$O$_{3}$/Al composites displayed cyclic hardening at all applied stress levels. The most of resultant displacement due to permanent plastic deformation occurred in less than the first 5% of fatigue life. Displacement-to-failure of the fatigue test was smaller than that of the tensile test because of accumulative damage by cumulative plastic deformation.

• Journal of Biosystems Engineering
• /
• v.41 no.1
• /
• pp.12-20
• /
• 2016

Purpose: Pepper prices have risen continuously because of a decrease in cultivation area; therefore, mechanical harvesting systems for peppers should be developed to reduce cost, time, and labor during harvest. In this study, a screw type picking head for a self-propelled pepper harvester was developed, and the optimal working conditions were evaluated considering helix types, winding directions of helix, and rotational speeds of the helix. Methods: The screw type was selected for the picking head after analyzing previous studies, and the device consisted of helices and a feed chain mechanism for conveying pepper branches. A double helix and a triple helix were manufactured, and rotational speeds of 200, 300, and 400 rpm were tested. The device was controlled by a variable speed (VS) motor and an inverter. Both the forward and reverse directions were tested for the winding and rotating directions of the helix. An experiment crop (cultivar: Longgreenmat) was cultivated in a plastic greenhouse. The test results were analyzed using the SAS program with ANOVA to examine the relationship between each factor and the performance of the picking head. Results: The results of the double and triple helix tests in the reverse direction showed gross harvest efficiency levels of 60-95%, mechanical damage rates of 8-20%, and net marketable portion rates of 50-80%. The dividing ratio was highest at a rotational speed of 400 rpm. Gross harvest efficiency was influenced by the types of helix and rotational speed. Net marketable portion was influenced by rotational speed but not influenced by the type of helix. Mechanical damage was not influenced by the type of helix or rotational speed. Conclusions: Best gross harvest efficiency was obtained at a rotational speed of 400 rpm; however, operating the device at that speed resulted in vibration, which should be reduced.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.6
• /
• pp.600-606
• /
• 2012

Upon investigation of the damaged wheels for high speed train it was determined that the damage was caused by rolling contact fatigue during operation of train. The major problems that railway vehicle system using wheel-rail has to face during operation of railway vehicle are rolling contact fatigue, cracks in wheels, cracks in rails and wheel-rail profile wear. If these deficiencies are not controlled at early stages the huge economical problems due to unexpected maintenance cost in railway vehicle can be happened. Also, If the accurate knowledge of contact conditions between wheel and rail can be evaluated, the damage of wheel can be prevented and the maintenance operation can save money. This paper presents the applicability of electro-magnetic technique to the detection and sizing of defects in wheel. Under the condition of continuous rolling contact fatigue the damage of wheel has continuously monitored using the applied sensor. It was shown that the usefulness of the applied sensor was verified by twin disc test and the measured damaged sizes showed good agreement with the damaged sizes estimated by electro-magnetic technique.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.5
• /
• pp.431-438
• /
• 2016

This research investigated the relationship between the corrosion damage characteristics of offshore wind steel substructure and the time of current density application by electrochemical accelerated short-term corrosion test. The galvanostatic corrosion was conducted on the steel specimens in natural seawater with a constant current density ranging from $1mA/cm^2$ to $200mA/cm^2$ for 1 ~ 180 min. Macro and micro observation was carried out on the surface of the corrosion damaged area using SEM and 3-dimensional analysis microscope. The weight loss of the specimens before and after was calculated as the difference between the initial weight prior to corrosion and weight after removal of the corrosion product. It was shown that during galvanostaic corrosion process, the corrosion behavior could be characterized by the onset of pitting corrosion in the early stage and the uniform corrosion in the late stage, showing damage development in the depth direction with the time of current application. The result of the 3D analysis revealed that both damage depth and surface roughness increased with increasing time of current application. The weight loss curves with time showed that a coefficient of determination ($R^2$) was relatively high for the relationship between the time of current application and weight loss. As a result, the degree of corrosion can be controlled by simply varying the time of current application.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.63-70
• /
• 2005

This study presents the thermal cracking on a commercial vehicle ventilated brake disk. Distributions of temperature and thermal stress of the disk were analysed, using FEM analysis, under the several driving conditions with actual vehicle specifications. The results from the fatigue tests on the disk material were compared with those from FEM analysis. In case of deceleration of 0.6 g with initial vehicle speed of 97, 140, and 160 km/h, the maximum compressive stress at the disk surface of disk due to braking was 224, 318, and 362 MPa, respectively. It was estimated that each damage fraction of 0.00005, 0.00050, 0.00136 per full stop was imposed on the brake disk in case of deceleration of 0.6 g with initial vehicle speed of 97, 140, and 160 km/h, respectively.

• Geomechanics and Engineering
• /
• v.20 no.3
• /
• pp.243-254
• /
• 2020

Due to the permanent damage to structures during earthquakes, soil liquefaction is an important issue in geotechnical earthquake engineering that needs to be investigated. Typical examples of soil liquefaction have been observed in many earthquakes, particularly in Alaska, Niigata (1964), San Fernando (1971), Loma Prieta (1989), Kobe (1995) and Izmit (1999) earthquakes. In this study, liquefaction behavior of uniform sands of different grain sizes was investigated by using the energy-based method. For this purpose, a total of 36 deformation-controlled tests were conducted on water-saturated samples in undrained conditions by using the cyclic simple shear test method and considering the relative density, effective stress and mean grain size parameters that affect the cumulative liquefaction energy. The results showed that as the mean grain size decreases, the liquefaction potential of the sand increases. In addition, with increasing effective stress and relative density, the resistance of sand against liquefaction decreases. Multiple regression analysis was performed on the test results and separate correlations were proposed for the samples with mean grain size of 0.11-0.26 mm and for the ones with 0.45-0.85 mm. The recommended relationships were compared to the ones existing in the literature and compatible results were obtained.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.259-262
• /
• 2009

The influence of pre-strain in low-cycle fatigue behavior of Fe-18Mn-0.05Al-0.6C TWIP steel was studied by conducting axial strain-controlled tests. As-received plates were deformed by rolling with reduction ratios of 10 and 30%, respectively. A triangular waveform with a constant frequency of 1 Hz was employed for low cycle fatigue test at the strain amplitudes in the range of ${\pm}0.4{\sim}{\pm}0.6$ pct. The results showed that low-cycle fatigue life was strongly dependent on the amount of pre-strain as well as the strain amplitude. Increasing the amount of prestrain, the number of reversals to failure was significantly decreased at high strain amplitudes, but the effect was negilgible at low strain amplitudes. A new model for predicting fatigue life of pre-strained body has been devised adding a correction term of ${\Delta}E_{pre-strain}$ to the energy-based fatigue damage parameter.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.839-843
• /
• 2001

For robotic endoscope, some researchers suggest pneumatic actuators based on inchworm motion. But, the existing endoscopes are not seemed to be replaced completely because human intestine is very sensitive and susceptible to damage. We design and test a new locomotion of robotic endoscope able to maneuver safely in the human intestine. The actuating mechanism is composed of two solenoids at each side and a single permanent magnet. When the current direction is reversed, repulsive force and attractive at the opposition side propels permanent magnet. Impact force against robotic endoscope transfer momentum from moving magnet to endoscope capsule. The direction and moving speed of the actuator can be controlled by adjusting impact force. Modeling and simulation experiments are carried out to predict the performance of the actuator. Simulation experiments show that force profile of permanent magnet is the dominant factor for the characteristic of the actuator. The results of simulations are verified by comparing with the experimental results.

• Journal of Biosystems Engineering
• /
• v.18 no.1
• /
• pp.21-29
• /
• 1993

The purpose of this study was to develope a potato combine which can be attached to and controlled by three-point hitch of tractors. A vibrating mechanism was designed and constructed to dig potatoes, and to evaluate the effects of vibration on the potato harvesting performance of the test machine, potato separation from soil, harvesting loss, and damage to the potatoes. Three types of potato pick-up mechanisms were constructed and tested. Digging performance and material flow on the blade were improved as the vibrating amplitude and frequency increased and as the travel speed decreased. The sum of unrecovered and damaged potatoes was up to 7.8%. Three pick-up devices were not found to be useful by failing to elevate about 30% of dug potatoes to a given height.