• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.248-253
• /
• 2016

Two substrate integrated waveguide (SIW)-based antennas for the application of software-defined radar are proposed and investigated herein. It is usually well known that SIWs are easily integrated, lightweight, have low insertion loss, and low interference levels compared to conventional microstrip structures. The primary function of the proposed antennas is to transmit continuous waves for indoor motion detection, with the lowest amount of loss and an appropriate amount of gain. Moreover, the results of this study show that the size of the antenna can be reduced significantly (i.e., by about 40%) by applying a meander line structure. The operating frequencies of the proposed antennas are both within the industrial, scientific, and medical band (i.e., 2.4-2.4835 GHz). Measured results of return loss are -16 dB and -20 dB at 2.435 GHz and 2.43 GHz, respectively, and the measured gain is 8.2 dBi and 5.5 dBi, respectively. Antenna design and verification are undertaken through commercially available full electromagnetic software.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.3
• /
• pp.47-52
• /
• 2012

This paper is in regard to design and experiment about the radar's circular polarization antenna operating in the Ku band. By using the Post to manufacture the circular polarization antenna using the linear antenna, it could reduce the structural size of an antenna. 3 Posts were used in order to broaden the Axial ration Bandwidth of the circular polarization antenna. The distance and length between Posts and Post were appropriately selected for the axial ratio optimization and applied in the design. It was verified that the designed antenna has the impedence bandwidth of 12.7%, axial ratio performance less than 2dB and gain of 7.8dBi.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.312-318
• /
• 2010

A small reconfigurable patch antenna is proposed to achieve polarization diversity for digital multimedia broadcasting systems at 2.6 GHz. To obtain polarization diversity, a pair of on-slit PIN diodes is inserted in each diagonal of a cross-shaped patch. Thus, four PIN-diodes on these slits are utilized to change the connection of the slits and thus achieve polarization. Bias circuits for the diodes are allocated in the cutting corner of the cross-shaped patch to minimize the antenna size. The antenna produces left-hand circular polarization, right-hand circular polarization, or linear polarization, depending on the PIN-diode status. Analysis of circular polarization operation is explicated. Measurements show a gain of about 1.5 dB, a cross polarization of about -20 dB, and an axial ratio of about 2.5 dB.

• ETRI Journal
• /
• v.45 no.4
• /
• pp.581-593
• /
• 2023

This paper proposes four-ring slot resonator-based MIMO antennas of 75×150 mm² without and with CSRR structures in the sub-6-GHz range. These orthogonal-fed antennas have shown diverse characteristics with dual polarization. L-shaped parasitic structures have increased the isolation (i.e., >40 dB) in the single-element antenna over the band of 3.4 GHz-3.8 GHz. A set of three CSRR structures in the MIMO antenna reduced the coupling between antenna ports placed in an inline arrangement and enhanced the isolation from 12 dB to 20 dB and the diversity characteristics. The S-parameters of both MIMO antennas are measured and used to evaluate MIMO parameters like ECC, TARC, MEG, and channel capacity loss. The simulation results show the variations in the gain and directivity on exciting linear and dual polarizations. The diversity performance of the reported MIMO antennas is suitable for 5G applications.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.443-444
• /
• 2008

A double-balanced frequency up-converter using the Gilbert cell structure has been designed with the TSMC $0.18\;{\mu}m$ CMOS library. The frequency up-converter consists of a Mixer core and IF / LO balun. Frequency Up-converter exhibits a 3.4 dB conversion gain with a - 7.6 dBm $P_{1dB}$ for IF power of -10 dBm and LO power of 0 dBm inputs. It also exhibits 92.2 % modulation depth as a ASK modulator.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.7
• /
• pp.1044-1052
• /
• 1999

A 2-stage 1 watt MMIC(Monolithic Microwave Integrated Circuits) HPA(High Power Amplifiers) at 20 GHz band has been designed and fabricated. The $0.15\mu\textrm{m}$ with the width of $400\mu\textrm{m}$for single device pHEMT technology was used for the fabrication of this MMIC HPA. Due to the series feedback technique from source to ground, bias circuits and stabilization circuits on the main microstrip line, the stability factors(Ks) are more than one at full frequency. The independent operation for each stage and excellent S11, S22 less than -20 dB have been obtained by using lange couplers. For beginning the easy design, linear S-parameters have been extracted from the nonlinear equivalent circuit in foundry library, and equivalent circuits of devices at in/output ports were calculated from this S-parameters. The measured performances, which are in well agreement with the predicted ones, showed the MMIC HPA in this paper has the minimum 15 dB of linear gain, -20 dB of reflection coefficients and 31 dBm of output power over 17~25 GHz.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.12
• /
• pp.80-87
• /
• 2013

A novel instrumentation amplifier(IA) using positive polarity current-conveyor(CCII+) for electronic measurement systems with low cost, wideband, and gain control with wide range is designed. The IA consists of two CCII+, three resistor, and an operational amplifier(op-amp). The principal of the operating is that the difference of two input voltages applied into two CCII+ used voltage and current follower converts into same currents, and then these current drive resistor of (+) terminal and feedback resistor of op-amp to obtain output voltage. To verify operating principal of the IA, we designed the CCII+ and used commercial op-amp LF356. Simulation results show that voltage follower used CCII+ has offset voltage of 0.21mV at linear range of ${\pm}$4V. The IA had wide gain range from -20dB to 60dB by variation of only one resistor and -3dB frequency for the gain of 60dB was 400kHz. The IA also has merits without matching of external resistor and controllable offset voltage using the other resistor. The power dissipation of the IA is 130mW at supply voltage of ${\pm}$5V.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.91-99
• /
• 2018

This paper has proposed a low-noise and high-linear RF receiver supporting TV white space from 470 MHz to 698 MHz), which is implemented in $0.13-{\mu}m$ CMOS technology. It consists of a low-noise amplifier, a RF band-pass filter, a RF amplifier, a passive down-conversion mixer, and a channel-selection low-pass filter. A low-noise amplifier and RF amplifier provide a high voltage gain to improve the sensitivity level. To suppress strong and nearby interferers, two RF filtering schemes have been performed by using a RF BPF and a down-conversion mixer. The proposed LPF has been based on the common-gate topology and adopted a bi-quad cell to achieve -24dB/oct characteristics. In addition, the RF receiver can support the overall TV band by controlling a LO frequency. The simulated results show a voltage gain of 56 dB, a noise figure of less than 2 dB, and an out-of-channel IIP3 of -2.3 dBm. It consumes 37 mA from a 1.5 V supply voltage.

• Journal of Advanced Navigation Technology
• /
• v.11 no.3
• /
• pp.288-295
• /
• 2007

In this paper, we proposed two systems, STTC scheme and STBC-TCM scheme, to enhance the reliability of HDR-WPAN system and analyzed BER(bit error rate) performance of the proposed systems over the slow fading channel. The proposed systems had a diversity gain and coding gain without increasing an additional channel bandwidth. However, in terms of reliability, about 4dB improvement at BER=$10^{-4}$ was obtained by the STBC-TCM scheme. In addition, HDR-WPAN system with STBC-TCM scheme had a linear rise in system complexity of ML(maximum likelihood). From the results, STBC-TCM scheme was more appropriate to improve the reliability and channel efficiency and to reduce complexity of HDR-WPAN system.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.9
• /
• pp.6-12
• /
• 1999

It is difficult to realize adaptive main carrier rejection circuit in feedforward-type LPA(Linear Power Amplifier) because the gain and nonlinear characteristics of power amplifier are changed according to operating frequency, voltage, temperature. Usually, pilot tones are used for adaptive LPA operation. but in this paper, the relative phase, which in obtained through I&Q demodulator using input signals as LO signals and main-path & sub-path signals as RF signals, and the magnitude of main-path & sub-path signals are compared, so main carrier rejection is obtained. The proposed method rejects main carriers by 28.34 ~ 34.66dB (@Po=36.2 ~ 28.2 dBm/tone) with two tones at 877MHz, 882MHz and also rejects main carriers by 31.3dB despite changing condition of operating voltage.