• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.9
• /
• pp.2477-2485
• /
• 1994

Air damper has a great advantage that is independent of temperature change. This paper presents an analysis approach and an application for designing nonviscous air damper with a piston and a cylinder. The objective functions for optimum design is damping coefficient and is maximized by changing two design variables that are length between piston and cylinder and orifice diameter. A digital computer program was developed which determines optimal air damper configuration for maximum damping coefficients. The results were applied to the automatic washer and are confirmed to be valid for the range of operating conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.1
• /
• pp.42-51
• /
• 1998

A 150 m$\^$3//hr, 30 kg/cm$\^$2/, air-cooled 3-stage reciprocating air compressor is designed to be used in starting large diesel engines of ships. A basic design procedure is presented to meet the targeted pressure and flow rate, and especially a volumetric efficiency of 80%. Temperature and stress analysis of the 1st stage cylinder are performed using axisymmetric FEM modelings. The dynamics of valve system is analyzed and stress at the 1st stage valve seat caused by valve impact is evaluated. To reduce friction loss and wear at the compressor engine system tribological design issues are reviewed and good design practices are suggested. Finally, forced-air pin-type interstage coolers are designed to dissipate generated compression heat at each stage.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.645-649
• /
• 1997

In case of swash plate type axial piston hydraulic motor, hydrostatic bearing used to achieve the lubrication effect on the mechanical sliding contact areas between the following parirs ; sliooer-pad and swash plate,piston and cylinder bore,valve plate and cylinder block, etc. This study discussed the basic charateristic for the hydrostatic slipper-pad bearings with the capillary or orifice restrictor under static load condition. And, we also development of hydrostatic bearing tester for hydrostatic balancing test of pistion & slipper-pad assembly, and some experimental data on supply pressure step responce are reported.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.10a
• /
• pp.184-188
• /
• 2000

The improved Green integral equation of overdetermined type applied to the radiation problem for an oscillating cylinder in the presence of weak current is presented. A two-dimensional Green function for the weak current is also presented. The present numerical solution of the Improved Green integral equation by the B-spline higher order Kelvin panel method is shown to be free of irregular frequencies which are present in the usual Green integral equation.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.4
• /
• pp.130-140
• /
• 1997

원형주상체 주위의 유동을 규명하기 위해 회류수조에서 원주방향으로 24개의 위치에 대하여 압력을 계측하였으며, laser sheet을 이용하여 유동을 가시화 하였다. Reynolds수가 4800에서 40000인 범위에 대하여 실험을 수행하였다. 또한, 원형단면체 주위의 비정상 층류유동에 대한 Navier-Stokes방정식의 해를 구하는 수치해석기법을 개발하였다. 효과적인 격자배치를 위하여 H와 O-type의 중첩격자를 사용하였고, 이산화 방법으로는 정규격자시스템에서 유한차분법을 적용하였다. 실험과 수치해석결과에서 뚜렷한 와류박리현상을 볼 수 있었으며, 압력계수 (C$_{p}$ ), 항력계수(C$_{D}$), 스트로얼수(St)를 정량적으로 비교하였을 때, 비교적 잘 일치하는 것을 확인하였다.다.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.86-87
• /
• 2011

In this paper, a conjugate heat transfer around cylinder with heat generation was investigated. Both forced convection and conduction was considered in the present finite element simulation. A finite element formulation based on SIMPLE type algorithm was adopted for the solution of the incompressible Navier-Stokes equations. We compared the finite element solution with that of Ansys fluent 12.0, in which finite volume method was employed for spatial discretization. It was found that the finite element method gave more accurate solution than Ansys fluent 12.0. Further, it was found that the maximum temperature inside cylinder is positioned at the rear side due to the flow separation.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.6
• /
• pp.35-42
• /
• 1999

This paper concentrates on the position control of a pneumatic cylinder under parameter variation. A closed-loop control is proposed to design the different controllers(P, PI, PID, PD controller) in order to choose the best con-troller based on the fast and accurate control of the system. It is shown that the control algorithm, is robust and effective in attaining the fast and accurate position control of system under time-dependent parameter variation. Experimental results showed that PD controller law is effective to obtain the fast response and to increase that sta-blity of the system The method is a useful control algorithm which always automatically adjusts the position con-trol in accordance with the error using carrier wave of triangle type regardless of changes on the operating condi-tion and physical differences between components.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.917-922
• /
• 2008

In order to reduce energy consumption, secondary controlled system has been applied to many types of equipments. In lifting equipments or press machines using hydraulic cylinder, a hydraulic transformer is used as a control component instead of a valve for motion control and a component for recovering potential energy of load. The transformer is combination of a variable displacement pump/motor as a secondary controlled element and a fixed displacement pump/motor. Based on the nominal model derived from mathematical model, the feedback type two-degree-of-freedom controller is designed and implemented. From simulation results, the disturbances including nonlinear friction torque, leakage flow and load force can be compensated and good positioning accuracy is obtained. It show that the proposed controller is effective.

• 한국전산유체공학회:학술대회논문집
• /
• 1998.05a
• /
• pp.138-144
• /
• 1998

The BGK equation, which is the kinetic model equation of Boltzmann equation, is solved using FDDO(finite difference with the discrete-ordinate method) to compute the rarefied flow of monatomic gas. Using reduced velocity distribution and discrete ordinate method, the scalar equation is transformed into a system of hyperbolic equations. High resolution ENO(Essentially Non-Oscillatory) scheme based on Harten-Yee's MFA(Modified Flux Approach) method with Strang-type explicit time integration is applied to solve the system equations. The calculated results are well compared with the experimental density field of NACA0012 airfoil, validating the developed computer code. Next. the computed results of circular cylinder flow for various Knudsen numbers are compared with the DSMC(Direct Simulation Monte Carlo) results by Vogenitz et al. The present scheme is found to be useful and efficient far the analysis of two-dimensional rarefied gas flows, especially in the transitional flow regime, when compared with the DSMC method.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.66-74
• /
• 1990

Friction between piston-ring assembly and cylinder wall of a spark ignition engine was evaluated under various engine operating conditions utilizing a grasshopper linkage system. The friction force was estimated by the force balance relation at the small end of connecting rod. Three forces were chosen to be measured for the objective. They were gas pressure inside the cylinder, inertia force of the piston-ring assembly, and the force exerted by the connecting rod. These forces were measured by a piezo type pressure sensor, an accelerometer and strain gauges, respectively. Comparisons were made with the frictional force evaluated by the conventional method where the assumption of constant rotational speed of engines was adopted. Due to the variation of rotational speed of engines, the conventional method was found to lead to a large error in the evaluation of the frictional force.