• 한국지반공학회논문집
• /
• 제29권8호
• /
• pp.37-51
• /
• 2013

에너지파일은 말뚝 내부에 열교환을 위한 순환파이프를 설치하여 파이프 내에 열전달 유체를 순환시킴으로써 주변 지반의 열에너지와 말뚝 간의 열교환을 가능하게 한 구조물이다. 에너지파일은 기존의 지중 열교환기와 비교하여 경제적, 시공적인 측면에서 많은 장점을 가지고 있다. 본 논문에서는 코일형 PHC 에너지파일을 시공하여 그 열적거동을 실험 및 수치해석을 통하여 평가하였으며, 해당 에너지파일의 예비설계를 수행하였다. 현장 시공된 코일형 PHC 에너지파일에 대한 현장 열응답시험(thermal response test, TRT)를 실시하고, 이 결과를 Man et al.(2010)이 제안한 개선된 원통형 열원 모델(solid cylinder source model) 결과와 비교하였다. 또한 현장 열응답 시험 결과를 FLUENT를 이용한 전산유체(computational fluid dynamics, CFD) 수치해석을 통해 모사함으로써, 대상 지반의 열전도도를 역해석을 통해 산정하였다. 코일형 PHC 에너지파일에 설치된 코일형 열교환 파이프의 파이프 루프 간 간격에 따른 열간섭을 평가하기 위하여 코일피치에 변화를 주며 수치해석을 수행하였으며, 결과를 통해 코일피치에 따른 에너지파일의 열거동 및 열교환 효율을 평가하였다. 마지막으로 수치해석을 통해 코일형 PHC 에너지파일과 일반적인 복합 U-형 열교환 파이프가 삽입된 PHC 에너지파일 간의 열교환 효율을 비교하여 코일형 PHC 에너지파일의 등가 열교환율(또는 등가 환산계수)을 제시하였고, 이를 PILESIM2를 이용한 설계 알고리즘에 적용함으로써 해당 에너지파일의 예비설계를 수행하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1410-1415
• /
• 2000

This paper introduces the experimental analysis of the resonator in the rolling piston type compressor for air conditioner. The resonator located between cylinder and bearing is a major factor in the noise reduction of the rotary compressor. Several shapes for the resonator which can be built in the space limitations are derived. Then optimal resonator type for the noise reduction is determined by noise tests. 6 design parameters of the type are found and optimal level for each design factor is deduced from Taguchi method.

• Agricultural and Biosystems Engineering
• /
• 제2권2호
• /
• pp.63-68
• /
• 2001

The objective of this study was to develop a real-time soil moisture meter using RF impedance. The impedance suchas capacitance and resistance (or conductance) was analyzed using parallel cylinder type capacitance probe(C-probe) and Q-meter (HP4342). The capacitance and conductance of soil increased as volumetric water content increased. The 5 MHz of modified Colpitts type crystal oscillator was designed to detect the capacitance change of the C-probe with moist soil. A third order polynomial regression model was proposed to describe the relationship between RF impedance and volumetric water content. The prototype real time moisture meter consisted of the C-probe, sample container, oscillator, frequency counter and related signal processing units. The calibration equation for measurement of volumetric moisture content of soil was developed and validated. The correlation coefficient and root mean square error between measured volumetric water content by oven method and predicted values by prototype moisture meter for unknown soil samples were 0.984 and 0.032$cm^3$$cm\^3$, respectively.

• Journal of Biosystems Engineering
• /
• 제18권4호
• /
• pp.371-381
• /
• 1993

Threshing operation is performed by impact, compression and friction forces inside the thresher. These values should be appropriate to the crop condition to enhance the threshing and separating efficiency and to decrease the grain damage. To analyze the threshing process inside the rasp-bar type thresher, impact, friction and compression forces were measured using transducers with strain gage circuits. To measure the impact forces and friction forces between the rasp-bar and crop, full bridge strain gage circuit was built on the rasp-bar holder. To measure the compression forces and circumferential friction forces between the concave and crop, two sets of full bridge strain gage circuits were built on the T-type concave transducer. Threshing work of wheat crop with 12% of moisture content was performed at 3 levels of compression ratio and with 3 replications. Each transducer could not measure the exact forces continuously because the transducer oscillates with the forces. However they could measure maximum forces and force distribution according to the time. Average friction coefficients between crop and concave was 0.61 not showing any significant difference according to the compression ratio. Average acceleration of the crop in the cylinder appeared from $70.6m/s^2$ to $140.8m/s^2$ according to the compression ratio. The velocity of the crop at the exit of the cylinder appeared from 10.7m/s to 15.0m/s according to the compression ratio.

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.175-182
• /
• 1997

The purpose of this study is to investigate the effects of intake manifold shapes to improve the engine performance in a 3-cylinder LPG engine with a closed loop fuel supply system. To know the flow resistance of intake manifolds with shape, the intake negative pressure of each runner in intake manifolds were measured by using the digital pressure meter at each driving condition. And, the engine torque and power have been measured with an engine dynamometer while adjusting the optimal fuel consumption ratio with a solenoid driver. As 속 results form this experiment, the torque characteris- tics were more improved with the plenum chamber(B type intake manifold) than with the banana type(A type intake manifold). The torque characteristics were improved at mid-engine speed(rpm) range as the inner diameter of the intake manifold became smaller. And also the optimum volume among the examined plenum chamber volume was 0.74 times(590cc) the displacement of the test engine.

• Nuclear Engineering and Technology
• /
• 제41권10호
• /
• pp.1323-1332
• /
• 2009

The IHX (Intermediate Heat eXchanger) for a pool-type SFR (Sodium-cooled Fast Reactor) system transfers heat from the primary high temperature sodium to the intermediate cold temperature sodium. The upper structure of the IHX is a coaxial structure designed to form a flow path for both the secondary high temperature and low temperature sodium. The coaxial structure of the IHX consists of a central downcomer and riser for the incoming and outgoing intermediate sodium, respectively. The IHX of a pool-type SFR is supported at the upper surface of the reactor head with an IHX support structure that connects the IHX riser cylinder to the reactor head. The reactor head is generally maintained at the low temperature regime, but the riser cylinder is exposed in the elevated temperature region. The resultant complicated temperature distribution of the co-axial structure including the IHX support structure may induce a severe thermal stress distribution. In this study, the structural feasibility of the current upper support structure concept is investigated through a preliminary stress analysis and an alternative design concept to accommodate the IHTS (Intermediate Heat Transport System) piping expansion loads and severe thermal stress is proposed. Through the structural analysis it is found that the alternative design concept is effective in reducing the thermal stress and acquiring structural integrity.

• 한국의류산업학회지
• /
• 제11권6호
• /
• pp.904-910
• /
• 2009

The aim of this study is to help out-size consumers purchase the ready-made clothes and improve clothing fitness by classifying the lower bodies of abdomen-obese adult males and by setting up some size system according to each size interval of obesity types. The including criteria for subjects in this study was over 25 kg/$m^2$ of the BMI, over 90 cm of waist, and over 0.85 of WHR, and a total of 538 adult males satisfying them were enrolled. Results are as follows; 1st, the higher the age bracket was, the more increase in each age bracket's lower-degree obesity rate there was along with the more decrease in moderate-degree, while the higher the age bracket was, the more increasing tendency toward each age bracket's abdominal obesity there was. 2nd, 3 clusters were categorized by cluster analysis, into abdominal obesity, high-degree-type, trapezoid-type and cylinder-type. And 3rd, as a consequence of size system establishment according to lower-body types, the basic body sizes and reference body sizes were different according to types even in commonly-appeared size names at sections of respective types. The research findings above suggests that it is necessary to figure out the obesity types according to waist and hip sizes representing basic sizes and to design the patterns in consideration of the characteristics of obese body shapes when lower-half body clothes are designed among obesity groups. And it may be used as a basic data to decide the desirable output of production according to respective body types.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.210-219
• /
• 2014

The MPI dual injection engine can enhance the fuel efficiency and engine power. By using one injector per one intake port, MPI dual injection engine has an excellent fuel atomization and targeting injection. As the basic research for the MPI Dual injection engine design, this research was investigated in order to understand the characteristic of the in-cylinder flow and fuel behavior according to engine temperature condition and the fuel type in the MPI dual injection engines. The 3D unsteady CFD simulation for the MPI Dual injection engine was performed using STAR-CD. The engine operating condition was 2,000 rpm/WOT. The parameters for this study were fuel types, fuel temperatures and wall temperatures. As a result, the intake air amount, evaporated fuel in the cylinder and the fuel film on the wall were presented according to parameters that depend on the fuel properties and engine wall temperature. Also, the results were influenced by in-cylinder flow such as the intake flow, back flow and so on.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2015년도 추계학술대회
• /
• pp.910-912
• /
• 2015

본 논문에서는 중장비나 댐의 수문 등의 적용된 유압 실린더의 변위(stroke)를 검출하여 유압 실린더의 정밀제어 또는 자동화를 위한 정전용량 센서(Capacitive Sensor) 및 변위 검출 시스템을 설계하였다. 기존 실린더의 변위 검출 방식인 코일을 이용한 자기장 센서, LVDT 센서 등은 높은 정확도에 비해 충격 및 진동 완화 또는 센서 보호 하우징(Housing) 등 부수적인 설비에 따른 높은 비용, 큰 부피와 같은 문제가 있다. 따라서 이러한 개선하기 위해 유압 실린더 내의 직접 적용되어 실린더의 변위 검출이 가능한 정전용량 센서를 설계하였으며, 설계한 정전용량 센서를 통하여 실린더의 변위에 따른 커패시턴스 값을 검출하여 실린더 위치 측정이 가능한 시스템을 설계 및 검증 하였다.

• 한국지반공학회논문집
• /
• 제39권1호
• /
• pp.5-14
• /
• 2023

말뚝이 근입된 지반의 융기는 말뚝에 추가적인 상향 주면 마찰력을 발생시켜 말뚝의 안정성을 저해할 수 있다. 본 연구에서는 말뚝의 일부에 지반 변형에 능동적으로 대응 가능한 부재가 삽입되어 말뚝에 작용하는 상향 주면 마찰력을 감소시킬 수 있는 새로운 말뚝 기초 양식을 제안하였다. 제안된 말뚝의 실효성을 검증하기 위하여 지반 변형 대응 부재로서 유압 실린더가 적용된 말뚝을 설계 및 제작하였다. 일반 말뚝과 제안된 말뚝을 대상으로 지반 융기 모사 실험을 수행하여 선단 하중, 주면 마찰력과 지반 변형 대응 부재의 팽창량에 따른 선단 하중의 변화를 분석하였다. 실험 결과, 매우 적은 양의 실린더 부재의 팽창에도 말뚝에 작용하는 인발 마찰력이 완전히 상쇄되며 이에 따라 선단 하중이 증가하였다. 그러나 실린더 부재의 과도한 팽창은 상향 마찰력의 감소를 넘어 부주면 마찰력을 발생시키므로 지반 팽창량 및 말뚝의 허용 변위를 고려한 적절한 지반 변형 대응 부재의 팽챵량 산정이 필요하다.