• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.874-877
• /
• 2004

We carried out this subject to observe electrochemical properties of 1,2-dioleoyl-sn- glycero-3-phosphocholine(DOPC) mixed with fatty acid containing azobenzene group by using cyclic voltammetry with a three-electrode system, An Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode in $NaClO_4$ solution. We investigated the photoisomerization and electrochemical property of the organic ultra thin film of fatty acid containing azobenzene was prepared on the hydrophilic ITO(idium tin oxide) glass plate by LB method. As a result, the absorption spectra of BASH and DOPC of mixture LB films was induced to photoisomerization by alternating irradiation of ultraviolet and visible light. A measuring range was reduced from initial potential to -1350mV, continuously oxidized to 1650 mV and measured to the initial point. The scan rate were 50, 100, 150 and 200 mV/s. As a results, LB films of BASH-DMPC appeared reversible process caused by the reduction-oxidation current from the cyclic voltammogram.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.1
• /
• pp.30-38
• /
• 2013

In this study, a catalyst slurry was prepared with a Pt/C catalyst, Nafion ionomer solution as a binder, an ionic liquid (IL) (1-butyl-3-methylimidazolium tetrafluoroborate), deionized water and ethanol as a solvent for the application to polymer electrolyte fuel cells (PEFCs) at high-temperatures. The effect of the IL in the electrode of each design was investigated by performing a cyclic voltammetry (CV) measurement. Electrodes with different IL distributions inside and on the surface of the catalyst electrode were examined. During the CV test, the electrochemical surface area (ESA) obtained for the Pt/C electrode without ILs gradually decreased owing to three mechanisms: Pt dissolution/redeposition, carbon corrosion, and place exchange. As the IL content increased in the electrode, an ESA decrement was observed because ILs leaked from the Nafion polymer in the electrode. In addition, the CVs under conditions simulating leakage of ILs from the electrode and electrolyte were evaluated. When the ILs leaked from the electrode, minor significant changes in the CV were observed. On the other hand, when the leakage of ILs originated from the electrolyte, the CVs showed different features. It was also observed that the ESA decreased significantly. Thus, leakage of ILs from the polymer electrolyte caused a performance loss for the PEFCs by reducing the ESA. As a result, greater entrapment stability of ILs in the polymer matrix is needed to improve electrode performance.

• Particle and aerosol research
• /
• v.10 no.2
• /
• pp.53-59
• /
• 2014

Palladium (Pd) nanoparticles attached graphene (GR) composite was synthesized for an enhanced glucose biosensor. Aerosol spray pyrolysis (ASP) was employed to synthesize the GR-Pd composite using a colloidal mixture of graphene oxide (GO) and palladium chloride ($PdCl_2$) precursor. The effects of the weight ratio of the Pd/GR on the particle properties including the morphology and crystal structure were investigated. The morphology of GR-Pd composites was generally the shape of a crumpled paper ball, and the average composite size was about $1{\mu}m$. Pd nanoparticles less than 20 nm in diameter were deposited on GR sheets and the Pd nanoparticles showed clear crystallinity. The characteristic of the glucose biosensor fabricated with the as-prepared GR-Pd composite was tested through cyclic voltammetry measurements. The biosensor exhibited a high current flow as well as clear redox peaks, which resulted in a superior ability of the catalyst in terms of an electrochemical reaction. The highest sensitivity obtained from the amperometric response of the glucose biosensor was $14.4{\mu}A/mM{\cdot}cm^2$.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.540-544
• /
• 2015

A bath for electrodeposition of platinum nanoparitcles on low-cost graphite substrates was developed to attach nanoparticles directly onto a substrate, and electrochemical characteristics of the electrodeposition of platinum nanoparticles were investigated. The reaction mechanism was examined by the analysis of polarization behavior. Cyclic voltammetry measurements revealed that the elecrodeposition of platinum nanoparticles was limited by mass transfer. The chronoamperometric study showed an instantaneous nucleation mechanism during the electrodeposition of platinum nanoparticles on graphite. Because graphite is much cheaper than other carbon-based substrates, the electrodeposition of platinum nanoparticles on the graphite is expected to have useful applications.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.4
• /
• pp.239-244
• /
• 2011

In this study, $Fe_3O_4$/graphene and CuO/graphene composites were synthesized by the polyol reduction method using ethylene glycol, and their performances as the anodes of lithium ion batteries were evaluated. The physical characteristics of the synthesized composites were analyzed by SEM, XRD, and TGA. In addition, their electrochemical properties were examined by the electrochemical analysis techniques such as charge/discharge performance, cyclic voltammetry, and AC impedance spectroscopy. The cells composed of $Fe_3O_4$/graphene and CuO/graphene composites showed better performance than the graphene electrode, due to the dispersion of nanosized $Fe_3O_4$ or CuO on the surface of graphene and the formation of good electrical network in the electrode. Their composites kept the reversible capacity more than 600 mAh/g even after the charging/discharging of 30 cycles.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.146.2-146.2
• /
• 2010

PEMFC를 구성하는 여러 부품 중 핵심부품은 MEA(Membrane Electrode Assembly)으로서 실제 연료전지 반응이 일어나며 연료전지의 성능을 결정하는 부품이다. 그러나 PEMFC의 특성 상 촉매로 귀금속인 Pt가 사용됨에 따라 경제성이 확보된 MEA의 성능을 얻기 위해선 현재 Pt 담지량을 0.3mg/$cm^2$ 이하로 크게 감소시키면서 Pt촉매의 고분산화와 미반응 사이트의 감소가 필요하다. 본 연구에서는 Pt 촉매의 미반응 사이트를 줄이고자 전기영동법에 의해 카본전극(carbon black + GDL) 상에 Pt 나노입자를 직접 석출시켜 Pt/C 촉매 전극을 제조 하였다. 본 실험에서는 가장 좋은 Pt 나노입자의 석출거동을 나타낸 30mA/$cm^2$, pH 2, duty cycle 25% 조건을 기준으로 하여 electro-deposition time을 통한 석출량 제어와 carbon paper의 wet proofing 정도에 따른 Pt의 석출거동을 조사하였으며, 종래의 방법으로 제조한 Pt/C 촉매전극의 전기화학적 특성과 비교 분석하였다. 전기영동 석출법에 사용된 Pt나노입자는 $H_2PtCl_6{\cdot}6H_2O$로부터 화학적 환원법으로 합성한 2~3nm 입경을 갖는 Pt콜로이드를 사용하였으며, magnetic stirring과 항온 ($20^{\circ}C$)을 유지하여 실험하였다. 전기영동 석출량 제어는 electro-deposition time을 5~25분까지 5분 간격으로 나누어 실험하였고 카본전극을 구성하는 carbon paper의 wet proofing 정도가 Pt 나노입자 석출거동에 미치는 영향을 조사하기 위하여 20, 40, 60%의 서로 다른 wet proofing 값을 갖는 carbon paper를 사용하여 Pt/C 촉매 전극을 제조하였다. 전기영동법으로 석출된 카본블랙 전극 상 Pt나노입자의 분산도와 담지량는 각각 FE-SEM과 TGA 장비를 사용하여 측정하였고, 제조된 Pt/C 촉매 전극의 전기화학적 촉매 특성은 cyclic voltammetry(CV)법으로 측정하였다.

• Resources Recycling
• /
• v.25 no.4
• /
• pp.49-53
• /
• 2016

The electro-refining process was performed to purify the casted tin crude metal from waste tin in methanesulfonic acid. The surface morphologies of electrodeposited tin on cathode were observed, the dendrite and delamination were inhibited by glycol group of organic additive. The impurity concentrations of tin crude metal and deposited metal were analyzed using ICP-OES. Quantitative analysis on casted tin crude metal showed that it consists of tin with 97.280 wt.% and several impurity metals of Ag, Cu, Pb, Ni, and etc. After tin electro-refining, the purity of tin increased up to 99.956 wt.%. Reduction current by cyclic voltammetry seems to be closely related to behavior of impurity in tin electro-refining.

• Applied Chemistry for Engineering
• /
• v.27 no.4
• /
• pp.449-454
• /
• 2016

In this study, highly monodispersed porous carbon microcapsules with a hollow core were synthesized using polystyrene (PS) beads as a hard template. The surface of PS was first modified with polyvinylpyrollidone (PVP) for the easy attachment of inorganic silica sol. After coating the surface of PVP modified PS microspheres with SBA-16 sol, the carbon microcapsules with a hollow macroporous core were fabricated through reverse replication method by filling carbon sources in the mesopores of silica mold. The hollow carbons having a mesoporous shell structure and narrow particle size distribution could be obtained after the carbonization of carbon source and the dissolution of silica mold by HF solution. The mesoporous characteristics and electrochemical properties of hollow carbon microcapsules were characterized by XRD, SEM, TEM, $N_2$ adsorption/desorption analysis and cyclic voltammetry. They showed the high electric conductivity and capability for use as efficient electro-materials such as a supercapacitor.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.2
• /
• pp.113-118
• /
• 2003

Processible polyaniline (PAM) dispersions consisting of polyaniline micro-particles, cyclohexanone, and a polymeric surfactant were prepared in a micro-milling machine with various mixing conditions. The electrochemical properties of the dispersion film coated on Pt electrode were investigated by cyclic voltammetry (CV). The electrochemistry of the PAM dispersion coatings was basically similar to a pure PAM coating based on the results of CV. The results of polarization measurements and open circuit potential measurements carried out in $3\;wt.\%$ NaCI solution showed increase in corrosion potential when the PANI dispersion coatings applied on steel surface. Variation of open circuit potential $(OCP,\;V_{OC})$ of the dispersion coating/steel electrodes was observed, which differed with milling conditions. The results demonstrated practical use of the conducting polymer dispersion as a coating material for corrosion prevention of steel.

• Membrane Journal
• /
• v.20 no.1
• /
• pp.8-12
• /
• 2010

Poly(3,4-ethylenedioxythiophene) (PEDOT), which has the highest stability in conducting polymer was employed to electrochromic (EC) film and studied about electrochromic properties according to the film fabrication method. PEDOT films were coated by two different methods, electropolymerization (EP) and vapor phase polymerization (VPP). Both of PEDOT films showed dark blue color at dedoped neutral state. Spectroelectrochemistry, switching ability and stability of the devices were investigated by UV-Vis Spectrophotometer and Cyclic voltammetry. Surface morphologies of the PEDOT VPP film at oxidized and reduced state were obtained by AFM. The average surface roughness of the PEDOT-VPP film was 50 nm and more homogeneous than that of the PEDOT-EP. The EC property from the PEDOT-VPP film was improved compared to that of the PEDOT-EP film, to show a response time of 1.5 sec, transmittancechange of 49%, and coloration efficiency of 402.